Mesoporous cerium oxide-anchored magnetic polyhedrons derived from MIL-100(Fe) for enhanced removal of arsenite from aqueous solution

Effective oxidation and adsorption of As(III) in water by nanoconfined Ce-Mn binary oxides with excellent reusability

Herein, a highly efficient As(III) purifier Ce-Mn@N201 with excellent reusability was developed by stepwise precipitating hydrated cerium(IV) oxides (HCO) and hydrated manganese(IV) oxides (HMO) inside N201, a widely-used gel-type anion exchange resin. Owing to confinement of unique nanopores in N201, the in-situ generated nanoparticles (NPs) inside Ce-Mn@N201 were highly dispersed with ultra-small sizes of around 2.6 nm. Results demonstrated that HMO NPs effectively oxidized As(III) to As(V) with the conversion of Mn(IV) to Mn(II), while the generated Mn2+ was mostly re-adsorbed onto the negatively-charged surface of HMO NPs. During the regeneration process by simple alkaline treatment, the re-adsorbed Mn2+ was firstly precipitated as (hydr)oxides of Mn(II) and then oxidized to HMO NPs by dissolved oxygen to fully refresh its oxidation capacity. Though HCO NPs mainly served as adsorbent for arsenic, they could partially oxidize As(III) to As(V) at the beginning, while the oxidation capacities continuously diminished with the irreversible conversion of Ce(IV) to Ce(III). In 10 consecutive adsorption-regeneration cycle, Ce-Mn@N201 efficiently decontaminated As(III) from 500 μg/L to below 5 μg/L with Mn2+ leaching less than 0.3% per batch. During 3 cyclic fixed-bed adsorptions, Ce-Mn@N201 steadily produced 8500-9150 bed volume (BV) and 3150-3350 BV drinkable water from the synthesized and real groundwater, respectively, with Mn leaching in effluent constantly < 100 μg/L.

Fe-based MOFs as promising adsorbents and photocatalysts for re-use water contained arsenic: Strategies and challenges

Arsenic (As) contaminated water, especially groundwater reservoirs, is a major issue worldwide owing to its hazardous consequences on human health and the global environment issues. Also, irrigating agricultural fields with As-contaminated water not only produces an accumulation of As in the soil but also compromises food safety due to As entering into agricultural products. Hence, there is an urgent need to develop an efficient method for As removal in water. Fe-based MOFs have attained special attention due to their low toxicity, high water stability, better physical and chemical properties, and high abundance of iron. The arsenic species removal by Fe-MOF follows the adsorption and oxidation mechanism where As (III) converts into As (V). Moreover, the adsorption mechanism is facilitated by electrostatic interactions, H-bonding, acid-base interaction, hydrophobic interactions, van der Waals forces, π-π stacking interactions, and coordinative bindings responsible for Fe-O-As bond generation. This review thoroughly recapitulates and analyses recent advancements in the facile synthesis and potential application of Fe-based MOF adsorbents for the elimination of As ions. The most commonly employed hydro/solvothermal, ultrasonic, microwave-assisted, mechanochemical, and electrochemical synthesis for Fe-MOF has been discussed along with their adsorptive and oxidative mechanisms involved in arsenic removal. The effects of factors like pH and coexisting ions have also been discussed. Lastly, the article also proposed the prospects for developing the application of Fe-based MOF in treating As-contaminated water.

MOFs@POMs-derived bimetallic oxide Fe2(MoO4)3 nanoparticles for sensitive colorimetric detection of salicylic acid in aspirin

A colorimetric sensing method for salicylic acid (SA) was developed by designing and fabricating bimetallic oxide nanozymes. Firstly, by calcinating MIL-100(Fe)@PMo12 (MOFs@POMs) at different temperature, Fe2(MoO4)3-Ts (T = 400℃, 500℃, 600℃, 700℃) nanoparticles (NPs) were successfully prepared. Secondly, by evaluating the peroxidase-like activities, Fe2(MoO4)3-600 NPs shows the best peroxidase-like activity attributed to the Fenton-like effect and the synergistic coupling interaction between Mo and Fe. Finally, based on the specific complexation between SA and Fe3+, a sensitive colorimetric sensor for SA was established, which exhibits superior selectivity and interference with a detection limit of 0.11 μM and a linear range of 10 to 100 μM, the lowest LOD for SA to date, to the best of our knowledge.

Ce(IV)-Based Metal-Organic Gel for Ultrafast Removal of Trace Arsenate from Water

As a potential replacement for metal-organic frameworks (MOFs), constructing metal-organic gels (MOGs) is an appealing but challenging topic since MOGs are a kind of shapeable MOF gels. Also, the rapid adsorption of trace heavy metal ions in aqueous media remains a serious challenge. Herein, a simple strategy for the synthesis of Ce(IV)-based metal-organic gel (Ce-MOG) was first developed for the rapid adsorption of trace As(V). The (NH₄)₂Ce(NO₃)₆ obtains hydroxide bridges after adding apposite NaOH, leading to [Ce₆O₄(OH)₄]¹²⁺ clustering and inducing fast and excessive nucleation rates, which also leads to coordination disturbance of MOF nanocrystals to obtain Ce-MOG. The Ce-OH groups are the key to gel formation through hydrogen bonding and are the active site for the ultrafast adsorption of As(V). As expected, the resultant Ce-MOG has an excellent adsorption rate, making it possible to effectively decontaminate 500 ppb of As(V) to below the World Health Organization (WHO) recommended threshold for drinking water (10 ppb) within 1 min. It achieves equilibrium adsorption in 10 min, and the final arsenate-removing efficiency reaches 99.8%. For Ce-MOF, the effluent concentration of As(V) is higher than the drinking water standard, while equilibrium adsorption takes 60 min. The initial adsorption rate of Ce-MOG, h(k₂q_e²) is calculated and indicated to be 67.67 mg g^-1 min^-1, about 19.96 times that of Ce-MOF (3.39 mg g^-1 min^-1). As such, the excellent As(V) decontamination rate, selectivity, and reusability of Ce-MOG indicate its great potential for practical drinking water purification.

Deep remediation of As(III) in water by La-Ce bimetal oxide modified carbon framework

Arsenic contamination of groundwater harms the health of millions of people, especially As(III), which is extremely toxic and difficult to remediate. Herein, we fabricated a reliable La-Ce binary oxide-anchored carbon framework foam (La-Ce/CFF) adsorbent for As(III) deep removal. Its open 3D macroporous structure ensures fast adsorption kinetic. The incorporation of an appropriate amount of La could enhance the affinity of La-Ce/CFF for As(III). The adsorption capacity of La-Ce₁₀/CFF reached 40.01 mg/g. It could purify the As(III) concentrations to drinking standard level (< 10 μg/L) over the pH ranges 3-10. It also possessed excellent anti-interference ability to the interfering ions. In addition, it worked reliably in the simulated As(III)-contaminated groundwater and river water. La-Ce₁₀/CFF could easily apply in fixed-bed, and La-Ce₁₀/CFF (1 g) packed column could purify 4580 BV (36.0 L) of As(III)-contaminated groundwater. When further considering the excellent reusability of La-Ce₁₀/CFF, it is a promising and reliable adsorbent for As(III) deep remediation.

Experimental investigation of the dehumidification and decarburization performance of metal-organic frameworks in solid adsorption air conditioning

Solid adsorption air conditioning systems use solid adsorption materials to co-adsorb water vapor and carbon dioxide, allowing the humidity and carbon dioxide concentration in the air-conditioned room to be controlled. Exploring the co-adsorption mechanism of H₂O and CO₂ is essential for the screening of adsorbent materials, system design, and system optimization in solid adsorption air conditioning systems. A fixed-bed adsorption-desorption device was built, and the dynamic adsorption properties of three MIL adsorbent materials MIL-101(Cr), MIL-101(Fe), and MIL-100(Fe) for co-adsorption of H₂O and CO₂ were studied. The results showed that all three MIL adsorbent materials are capable of performing co-adsorption of H₂O and CO₂ and meet the requirements of solid adsorption air conditioning systems. MIL-101(Cr) is recommended for solid adsorption air conditioners where dehumidification is the main focus, while MIL-100(Fe) is recommended for solid adsorption air conditioners where carbon removal is the main focus.

Cr-Based MOF for Efficient Adsorption of Au at Low Concentrations

The efficient enrichment and selection of Au are crucial for gold recovery. The adsorption technology is considered to have potential due to the advantages of operation simplicity and green processability. Nevertheless, the poor Au selectivity at low concentrations in complex solutions limits the further application of the adsorption technology. In this work, a novel Cr-based MOF adsorbent was successfully synthesized using 1,2,4-triazole and 4-aminobenzoic acid as ligands. Benefitting from the surface positive charge and extensive chelation and reduction sites, the novel Cr-based MOF exhibited a total adsorption capacity of up to 357 mg/g and excellent adsorption selectivity toward Au(III) in the complex metal mixed solutions, such as simulated sewage ash waste liquid and actual e-waste leachate. Furthermore, the adsorption kinetics, isotherms, and thermodynamics were discussed in depth for investigating the adsorption mechanisms of the MOF. The PXRD and XPS analyses reveal that the adsorption process involves complexation, redox, and electrostatic interactions. We believe that this study of novel Cr-based MOF adsorbents for efficient Au adsorption is meaningful for further application in the gold recovery technology from e-waste.

Collaborative Construction of a Silver Nanocluster Fluorescent Probe Using the Pyridinium-Based Ionic Liquid [C4py][DCA]

A silver nanocluster fluorescent probe was synthesized by using the pyridinium-based ionic liquid [C₄py][DCA] as the protective agent, AgNO₃ as the precursor, and NaBH₄ as the reducing agent. The presence of pyridine group enhanced the fluorescence intensity of Ag nanoclusters and facilitated the coordination interaction between Ag nanoclusters and AsO₃ ^3-. Therefore, the collaborative construction of a silver nanocluster probe using the pyridinium-based ionic liquid [C₄py][DCA] offered outstanding selectivity and sensitivity to detect AsO₃ ^3- in water. More interestingly, the fluorescent probe quenched by AsO₃ ^3- could be recovered with the addition of H₂O₂. This fluorescent probe provided a rapid and superior method for the detection of As(III) in the linear concentration range of 0-60 ppb with the lowest detection limit of 0.60 ppb. The mechanism of fluorescence quenching was a static quenching, considered to be due to electron migration between functional groups on the surface of Ag nanoclusters constructed with [C₄py][DCA] and AsO₃ ^3-.