Emerging waste valorisation techniques to moderate the hazardous impacts, and their path towards sustainability

Perspectives on the use of biochar in the valorization of mining wastes from sulfide minerals flotation: Recovery of metals and effects on toxicity

This study aims to evaluate the use of two biochars obtained by pyrolysis of sugarcane-bagasse and compare it with commercial activated carbons as catalysts for the recovery of metals from one mining waste from sulfide minerals flotation (MW). It is also intended to determine the influence of carbon materials on the toxicity of the final residues. Leaching tests were performed in 250 mL erlenmeyer flasks using plates with magnetic stirrers during 24 h, at 90 °C and a stirring speed of 350 rpm. For each test, 5 g of MW were mixed with carbon material in two ratios of MW/carbon material (1/0.1 and 1/0.2 wt/wt) and 100 mL of leaching agent (H2SO4 solution at pH = 0.8-0.9 and 5 gL-1 of Fe3+). The experimental results showed that the addition of biochar and activated carbon enhances the recovery of Cu and Zn. The use of commercial activated carbons in ratios of 1/0.1 and 1/0.2 MW/carbon material leads to the extraction of more than 91 % of Cu and 97 % of Zn, after 24 h of leaching. For biochars, the highest recovery values of Cu (82.9 %) and Zn (98.1 %) were achieved with biochar prepared at 750 °C and used in the ratio of 1/0.2. However, the addition of carbon materials does not improve the recovery of Co. The presence of carbon materials decreased the electrical conductivity and pH of the final residue. The leaching of samples MW + W35 (1/0.1) and MW + BC550 (1/0.1) leads to a germination index higher than 90 %. For two biochars, all samples showed non-phytotoxicity.

Amorphous RuO2 Catalyst for Medium Size Carboxylic Acid to Alkane Dimer Selective Kolbe Electrolysis in an Aqueous Environment

The catalytic transformation of biomass-derived volatile carboxylic acids in an aqueous environment is crucial to developing a sustainable biorefinery. To date, Kolbe electrolysis remains arguably the most effective means to convert energy-diluted aliphatic carboxylic acids (carboxylate) to alkane for biofuel production. This paper reports the use of a structurally disordered amorphous RuO2 (a-RuO2 ) that is synthesized facilely in a hydrothermal method. The a-RuO2 is highly effective towards electrocatalytic oxidative decarboxylation of hexanoic acid and is able to produce the Kolbe product, decane, with a yield 5.4 times greater than that of commercial RuO2 . A systematic study of the reaction temperature, current intensity, and electrolyte concentration reveals the enhanced Kolbe product yield is attributable to the more efficient oxidation of the carboxylate anions for the alkane dimer formation. Our work showcases a new design idea for establishing an efficient electrocatalysts for decarboxylation coupling reaction, providing a new electrocatalyst candidate for Kolbe electrolysis.

Preparation, characterisation and applications of bone char, a food waste-derived sustainable material: A review

The production of increasing quantities of by-products is a key challenge for modern society; their valorisation - turning them into valuable compounds with technological applications - is the way forward, in line with circular economy principles. In this review, the conversion of bones (by-products of the agro-food industry) into bone char is described. Bone char is obtained with a process of pyrolysis, which converts the organic carbon into an inorganic graphitic one. Differently from standard biochar of plant origin, however, bone char also contains calcium phosphates, the main component of bone (often hydroxyapatite). The combination of calcium phosphate and graphitic carbon makes bone char a unique material, with different possible uses. Here bone chars' applications in environmental remediation, sustainable agriculture, catalysis and electrochemistry are discussed; several aspects are considered, including the bones used to prepare bone char, the preparation conditions, how these affect the properties of the materials (i.e. porosity, surface area) and its functional properties. The advantages and limitations of bone chars in comparison to traditional biochar are discussed, highlighting the directions the research should take for bone chars' performances to improve. Moreover, an analysis on the sustainability of bone chars' preparation and use is also included.

Building risk mitigation strategies for circularity adoption in Indian textile supply chains

Textile industries are among the most polluting and demand urgent management measures to mitigate their negative environmental impact. Thus, it is imperative to incorporate the textile industry into the circular economy and to foster sustainable practices. This study aims to establish a comprehensive, compliant decision framework to analyse risk mitigation strategies for circular supply chain (CSC) adoption in India's textile industries. The Situations Actors Processes and Learnings Actions Performances (SAP-LAP) technique analyses the problem. However, interpreting the interacting associations between the SAP-LAP model-based variables is somewhat lacking in this procedure, which might skew the decision-making process. As a result, in this study, the SAP-LAP method is accompanied by a novel ranking technique, namely, the Interpretive Ranking Process (IRP), which reduces decision-making issues in the SAP-LAP method and aids in evaluating the model by determining the ranks of variables; furthermore, the study also offers causal relationships among the various risks and risk factors and various identified risk-mitigation actions by constructing Bayesian Networks (BN) based on conditional probabilities. The study's originality represents the findings using an instinctive and interpretative choice approach to address significant concerns in risk perception and mitigation techniques for CSC adoption in the Indian textile industries. The suggested SAP-LAP and the IRP-based model would assist firms in addressing risk mitigation techniques for CSC adoption concerns by providing a hierarchy of the various risks and mitigation strategies to cope with. The simultaneously proposed BN model will help visualise the conditional dependency of risks and factors with proposed mitigating actions.

Silica-derived materials from agro-industrial waste biomass: Characterization and comparative studies

The management and final disposal of agro-industrial wastes are one of the main environmental problems. Due to the presence of silica in some agricultural by-products, it is possible to convert waste into materials with advanced properties. This contribution was aimed to extract and characterize silica materials from various feedstocks including sugarcane bagasse (SCB), corn stalk (CS), and rice husk (RH). Silica yields of 17.91%, 9.39%, and 3.25% were obtained for RH, CS, and SCB. On the other hand, the textural properties show that the siliceous materials exhibited mesoporous structures, with high silica composition in the materials due to the formation of crystalline SiO₂ for SCB and CS and amorphous for RH. XPS spectra demonstrate the presence of Si⁴⁺ species in RH, and Si³⁺/Si⁴⁺ tetrahedra in SCB and CS.

Valorization of agro-industrial wastes into animal feed through microbial fermentation: A review of the global and Ghanaian case

Agricultural and industrial activities around the world lead to the production of large quantities of agro-industrial wastes (e.g., peels of cassava, pineapple, plantain, banana, and yam, as well as rice husks, rice bran , corn husks, corn cobs, palm kernel cake, soybean meal, wheat bran, etc.). These agro-industrial wastes are discarded indiscriminately, thereby polluting the environment and becoming hazardous to human and animal health. Solid-state fermentation (SSF), a microbial fermentation process, is a viable, efficient approach that transforms discarded agro-industrial wastes into a plethora of useful value-added bioproducts. There is growing interest in the application of SSF in valorizing agro-industrial wastes for the production of fermented, protein-rich animal feed within the livestock industry. SSF reduces anti-nutritional factors whose presence hinders the digestibility and bioavailability of nutrients in agro-industrial wastes. Thus, the application of SSF improves the nutrient contents and quality of valorized agro-industrial wastes as animal feed. Fermented animal feed production may be safer, cheaper and enhance the overall growth performance and health of animals. SSF, therefore, as a strategic approach in a circular bioeconomy, presents economic and practical advantages that guarantee efficient recycling and valorization of agro-industrial wastes that ameliorate environmental pollution. This paper reviews the status of global and local Ghanaian biotransformation and valorization of agro-industrial wastes through SSF for the production of nutrient-rich animal feed.

What's stopping the waste-treatment industry from adopting emerging circular technologies? An agent-based model revealing drivers and barriers

Many new circular economy technologies are gaining momentum, yet research on the complexity of adoption decisions driven by uncertainties, both at technology and ecosystem level, is lacking. In the present study, an agent-based model was developed to study factors that influence the adoption of emerging circular technologies. The case of the waste treatment industry was chosen, specifically its (non-) adoption of the so-called "Volatile Fatty Acid Platform", a circular economy technology that facilitates both the valorization of organic waste into high-end products as well as their sale on global markets. Model results show adoption rates under 60% due to effects of subsidies, market growth, technological uncertainty and social pressure. Furthermore, the conditions were revealed under which certain parameters have the most effect. An agent-based model enabled use of a systemic approach to reveal the mechanisms of circular emerging technology innovation that are most relevant for researchers and waste treatment stakeholders.

On the removal efficiency of copper ions in wastewater using calcined waste eggshells as natural adsorbents

Eggshells offer many advantages as adsorbents, such as affordability without special preparations other than pulverization and calcination. However, the manufacturing industry generally has a severe problem with high concentrations of heavy metals in wastewater. The purpose of this study was to use eggshell byproducts and calcined eggshell treatment for the adsorption of copper in an aqueous solution. The reaction time, metal concentration, adsorbent dose, temperature, and pH were evaluated using primary factors followed by the response surface method (RSM) to investigate the optimum conditions for eggshell byproducts and calcined eggshell adsorption treatment. The results of the one-factor-at-a-time experiment showed that the optimal adsorption rate was obtained from treatment at 24 h, 25 mg/L, 10 mg, and 25 °C. In addition, the effect of pH on the adsorption rates of eggshells and eggshells with membrane were detected at pH values of 5 and 5.9 and found to be 95.2, 90.5, and 73.3%. The reaction surface experiment showed that the best adsorption rate reached 99.3% after calcination at 900 °C for 2 h and a 20 min reaction. The results showed that eggshells, eggshell membranes, eggshells with membrane, and calcined eggshells could be applied to remove copper ions from industrial wastewater. The adsorption capacity of the calcined eggshell is better than that of the non-calcined eggshell and has good neutrality in acidic industrial wastewater. Therefore, it is convenient and practical for practical production and application. Likewise, this study conveys promising findings in the context of improving wastewater treatment based on a circular economy approach to waste reuse in the food industry and represents a valuable direction for future research.

An Insight into Microbial Inoculants for Bioconversion of Waste Biomass into Sustainable "Bio-Organic" Fertilizers: A Bibliometric Analysis and Systematic Literature Review

The plant-microbe holobiont has garnered considerable attention in recent years, highlighting its importance as an ecological unit. Similarly, manipulation of the microbial entities involved in the rhizospheric microbiome for sustainable agriculture has also been in the limelight, generating several commercial bioformulations to enhance crop yield and pest resistance. These bioformulations were termed biofertilizers, with the consistent existence and evolution of different types. However, an emerging area of interest has recently focused on the application of these microorganisms for waste valorization and the production of "bio-organic" fertilizers as a result. In this study, we performed a bibliometric analysis and systematic review of the literature retrieved from Scopus and Web of Science to determine the type of microbial inoculants used for the bioconversion of waste into "bio-organic" fertilizers. The Bacillus, Acidothiobacillus species, cyanobacterial biomass species, Aspergillus sp. and Trichoderma sp. were identified to be consistently used for the recovery of nutrients and bioconversion of wastes used for the promotion of plant growth. Cyanobacterial strains were used predominantly for wastewater treatment, while Bacillus, Acidothiobacillus, and Aspergillus were used on a wide variety of wastes such as sawdust, agricultural waste, poultry bone meal, crustacean shell waste, food waste, and wastewater treatment plant (WWTP) sewage sludge ash. Several bioconversion strategies were observed such as submerged fermentation, solid-state fermentation, aerobic composting, granulation with microbiological activation, and biodegradation. Diverse groups of microorganisms (bacteria and fungi) with different enzymatic functionalities such as chitinolysis, lignocellulolytic, and proteolysis, in addition to their plant growth promoting properties being explored as a consortium for application as an inoculum waste bioconversion to fertilizers. Combining the efficiency of such functional and compatible microbial species for efficient bioconversion as well as higher plant growth and crop yield is an enticing opportunity for "bio-organic" fertilizer research.

Bio-Electrochemical Performance of a Ceramic Microbial Fuel Cell Treating Kitchen Waste Leachate: Effect of Organic Loading Rate and Anode Electrode Surface Area

Performance evaluation of a ceramic microbial fuel cell (CMFC) by varying organic strength, hydraulic retention time (HRT) and anode electrode surface area (AESA) to treat leachate generated from acidogenesis of kitchen waste (KW) was studied by the central composite design of experiment. The increase in organic loading rate (OLR) positively affected power density (PD) while negatively influencing organic removal and coulombic efficiency (CE). This behavior is possible due to substrate inhibition and the coercive effect of low HRT, i.e., substrate washout, biofilm abrasion, and reduced contact period, while at high HRT, the volatile fatty acid (VFA) degradation improved. Since acetic acid is the final product of long-chain VFAs degradation, a pseudo consumption order for VFAs was obtained: butyric > propionic > acetic. The AESA aided organics removal and PD but had a negligible effect on CE. According to ANOVA, the COD removal was linearly modeled, while PD and CE were quadratic. The validation runs (VR) proved efficient as the highest COD removal was for VR2 (83.7 ± 3.6%), while maximum PD and CE values obtained were 0.224 ± 0.02 W/m3 and 2.62 ± 0.33%, respectively, for VR3, supported by the lower anode potential.

Electric Current Generation by Increasing Sucrose in Papaya Waste in Microbial Fuel Cells

The accelerated increase in energy consumption by human activity has generated an increase in the search for new energies that do not pollute the environment, due to this, microbial fuel cells are shown as a promising technology. The objective of this research was to observe the influence on the generation of bioelectricity of sucrose, with different percentages (0%, 5%, 10% and 20%), in papaya waste using microbial fuel cells (MFCs). It was possible to generate voltage and current peaks of 0.955 V and 5.079 mA for the cell with 20% sucrose, which operated at an optimal pH of 4.98 on day fifteen. In the same way, the internal resistance values of all the cells were influenced by the increase in sucrose, showing that the cell without sucrose was 0.1952 ± 0.00214 KΩ and with 20% it was 0.044306 ± 0.0014 KΩ. The maximum power density was 583.09 mW/cm² at a current density of 407.13 A/cm² and with a peak voltage of 910.94 mV, while phenolic compounds are the ones with the greatest presence in the FTIR (Fourier transform infrared spectroscopy) absorbance spectrum. We were able to molecularly identify the species Achromobacter xylosoxidans (99.32%), Acinetobacter bereziniae (99.93%) and Stenotrophomonas maltophilia (100%) present in the anode electrode of the MFCs. This research gives a novel use for sucrose to increase the energy values in a microbial fuel cell, improving the existing ones and generating a novel way of generating electricity that is friendly to the environment.

Optical Analysis of Blast Furnace Gas Combustion in a Laboratory Premixed Burner

The use of blast furnace gas (BFG) as a fuel provides an alternative for waste stream valorization in the steel industry, enhancing the sustainability and decarbonization of its processes. Nevertheless, the implementation of this solution on an industrial scale requires a continuous control of the combustion due to the low calorific value of BFG. This work analyzes the combustion behavior and monitoring of BFG/CH₄ blends in a laboratory premixed fuel burner. We evaluate several stable combustion conditions by burning different BFG/CH₄ mixtures at a constant power rate over a wide range of air/fuel equivalence ratios. In addition, relevant image features and chemiluminescence emission spectra have been extracted from flames, using advanced optical devices. BFG combustion causes an increase in CO₂ and CO emissions, since those fuels are the main fuel components of the mixture. On the other hand, NO _x emissions decreased because of the low temperature of combustion of the BFG and its mixtures. Chemiluminescence shows that, in the case of CH₄ combustion, peaks associated with hydrocarbons are present, while during the substitution of CH₄ by BFG those peaks are attenuated. Image flame features extracted from both ultraviolet and visible bandwidths show a correlation with the fuel blend and air/fuel equivalence ratio. In the end, methodologies developed in this work have been proven to be valuable alternatives with a high potential for the monitoring and control of BFG cofiring for the steel industry.

Analysis of Material-Characterization Properties of Post-Production Waste—The Case of Apple Pomace

The paper presents the material-characterization properties of apple pomace—the post-production waste of juice pressing. Tests were carried out on the basic physical properties of apple pomace: color, specific-density, and energy properties. Extensive material-composition analyses based on DSC (differential scanning calorimetry) and TGA (thermogravimetry) methods were also performed. It has been shown that pomace, due to its energy value, can be a good fuel. The obtained thermal data confirm the presence of cellulose, hemicelluloses, lignins and pectins in the analyzed pomace. The results confirm that dried apple pomace is microbiologically stable with good health-promoting properties.

Application of solid-state fermentation by microbial biotechnology for bioprocessing of agro-industrial wastes from 1970 to 2020: A review and bibliometric analysis

This paper reviews the pertinent literature from 1970 to 2020 and presents a bibliometric analysis of research trends in the application of solid-state fermentation in the bioprocessing of agro-industrial wastes. A total 5630 publications of studies on solid-state fermentation that comprised of 5208 articles (92.50%), 340 book chapters (6.04%), 39 preprints (0.69%), 32 proceedings (0.56%), 8 edited books (0.14%) and 3 monographs (0.05%) were retrieved from Dimensions database. A review of the literature indicated that (i) fermentation of solid substrates is variously defined in the literature over the past 50 years, where "solid-state fermentation" is the most dominant research term used, and (ii) key products derived from the valorization of agro-industrial wastes through solid-state fermentation include, among others, enzymes, antioxidants, animal feed, biofuel, organic acids, biosurfactants, etc. Bibliometric analyses with VOSviewer revealed an astronomic increase in publications between 2000 and 2020, and further elucidated the most frequently explored core research topics, the most highly cited publications and authors, and countries/regions with the highest number of citations. The most cited publication between 2010 and 2020 had 382 citations compared to 725 citations for the most cited publication from 1970 to 2020. Ashok Pandey from India was the most published and cited author with 123 publications and 8,613 citations respectively; whereas Bioresource Technology was the most published and cited journal with 233 publications and 12,394 citations. Countries with the most publications and citations are Brazil, France, India, and Mexico. These findings suggest that research in the application of solid-state fermentation for bioprocessing of agro-industrial wastes has gained prominence over the past 50 years. Future perspectives and implications are discussed.