Copper removal and recovery from electroplating effluent with wide pH ranges through hybrid capacitive deionization using CuSe electrode

Confinement-induced Ni-based MOF formed on Ti3C2Tx MXene support for enhanced capacitive deionization of chromium(VI)

MXenes, as a novel two-dimensional lamellar material, has attracted much attention. However, MXenes lamellar are prone to collapse and stacking under hydrogen bonding and interlayer van der Waals forces, which affects their electrochemical and capacitive deionization performance. A three-dimensional Ni-1,3,5-benzenetricarboxylate/Ti3C2Tx (Ni-BTC/Ti3C2Tx) composite electrode material was developed to enhance the electrochemical and capacitive deionization performance. The uniformly decorated Ni-BTC can prevent MXenes from aggregation and provide a large specific surface area and rich pore structure. As a substrate supporting Ni-BTC, MXenes can effectively disperse the growth of Ni-BTC and enhance the ion transport rate. In addition, the unique three-dimensional structure of Ni-BTC/Ti3C2Tx provides horizontal charge transfer paths like two-dimensional nanosheets and has unique vertical charge transfer paths between nanosheets. Therefore, the Ni-BTC/Ti3C2Tx exhibits an exceptional chromium(VI) removal rate of 94.1%. The electrosorption capacity of the Ni-BTC/Ti3C2Tx for chromium(VI) is 124.5 mg g-1, much higher than that of the pure Ti3C2Tx (55.5 mg g-1). The superior CDI efficiency accomplished through the Ni-BTC/Ti3C2Tx electrode is due to the unique three-dimensional network structure and synergistic effect of the pseudocapacitance generated by the unique assembly of Ni-BTC and Ti3C2Tx. Ni-BTC/Ti3C2Tx is a promising CDI electrode material that can be used for capacitive deionization.

Simultaneous Cu(II)-EDTA decomplexation and Cu(II) recovery using integrated contact-electro-catalysis and capacitive deionization from electroplating wastewater

The complex of heavy metals and organic acids leads to high difficulty in heavy metals separation by traditional technologies. Meanwhile, alkaline precipitation commonly used in industry causes the great consumption of resources and extra pollution. Herein, the effective decomplexation of Cu(Ⅱ)-EDTA and synchronous recycling of Cu2+ were realized by contact-electro-catalysis (CEC) coupled with capacitive deionization (CDI) innovatively. In particular, fluorinated ethylene propylene (FEP) as dielectric powders could generate reactive oxygen species under ultrasonic stimulation, realizing continuous deaminization and decarboxylation of Cu(Ⅱ)-EDTA and accelerating the totally breakage of Cu-O and Cu-N bonds. Additionally, the degradation pathway and intermediates evolution of Cu(Ⅱ)-EDTA were investigated using various characterization methods. It was confirmed that decarboxylation predominantly governed the degradation process of Cu(Ⅱ)-EDTA in CEC. During the course of treatment, the degradation ratio of Cu(Ⅱ)-EDTA reached 86.4 % within 150 min. Impressively, this strategy had satisfactory applicability to other metal combinations and excellent cycle stability. Subsequently, the released Cu ions were captured by CuSe cathode electrode through CDI. This research elucidated the degradation mechanism of persistent organic pollutant during CEC, and provided a novel approach for efficiently treating industrial wastewater containing metal complexes and advancing the exploitation and utilization of new technologies for metal recovery.

Electrochemical processes for the treatment of contaminant-rich wastewater: A comprehensive review

Global water demand and environmental concerns related to climate change require industries to develop high-efficiency wastewater treatment methods to remove pollutants. Likewise, toxic pollutants present in wastewater negatively affect the environment and human health, requiring effective treatment. Although conventional treatment processes remove carbon and nutrients, they are insufficient to remove pharmaceuticals, pesticides, and plasticizers. Electrochemical processes effectively remove pollutants from wastewater through the mineralization of non-biodegradable pollutants with consequent conversion into biodegradable compounds. Its advantages include easy operation, versatility, and short reaction time. In this way, this review initially provides a global water scenario with a view to the future. It comprises global demand, treatment methods, and pollution of water resources, addressing various contaminants such as heavy metals, nutrients, organic compounds, and emerging contaminants. Subsequently, the fundamentals of electrochemical treatments are presented as well as electrochemical treatments, highlighting the latest studies involving electrocoagulation, electroflocculation, electroflotation, capacitive deionization and its derivatives, eletrodeionization, and electrochemical advanced oxidation process. Finally, the challenges and perspectives were discussed. In this context, electrochemical processes have proven promising and effective for the treatment of water and wastewater, allowing safe reuse practices and purification with high contaminant removal.

Copper hexacyanoferrate/carbon sheet combination with high selectivity and capacity for copper removal by pseudocapacitance

The efficient capture of copper ions (Cu2+) in wastewater has dual significance in pollution control and resource recovery. Prussian blue analog (PBA)-based pseudocapacitive materials with open frameworks and abundant metal sites have attracted considerable attention as capacitive deionization (CDI) electrodes for copper removal. In this study, the efficiency of copper hexacyanoferrate (CuHCF) as CDI electrode for Cu2+ treating was evaluated for the first time upon the successful synthesis of copper hexacyanoferrate/carbon sheet combination (CuHCF/C) by introducing carbon sheet as conductive substrate. CuHCF/C exhibited significant pseudocapacitance and high specific capacitance (52.92 F g-1) through the intercalation, deintercalation, and coupling of Cu+/Cu2+ and Fe2+/Fe3+ redox pairs. At 0.8 an applied voltage and CuSO4 feed liquid concentration of 100 mg L-1, the salt adsorption capacity was 134.47 mg g-1 higher than those of most reported electrodes. Moreover, CuHCF/C demonstrated excellent Cu2+ selectivity in multi-ion coexisting solutions and in actual wastewater experiments. Density functional theory (DFT) calculations were employed to elucidate the mechanism. This study not only reveals the essence of Cu2+ deionization by PBAs pseudocapacitance with promising potential applications but also provides a new strategy for selecting efficient CDI electrodes for Cu2+ removal.

In-situ registration subtraction image segmentation algorithm for spatiotemporal visualization of copper adsorption onto corn stalk-derived pellet biochar by micro-computed tomography

The non-homogeneous structure and high-density ash composition of biochar matrix pose significant challenges in characterizing the dynamic changes of heavy metal adsorption onto biochar with micro-computed tomography (Micro-CT). A novel in-situ registration subtraction image segmentation method (IRS) was developed to enhance micro-CT characterization accuracy. The kinetics of Cu(II) adsorption onto pellet biochar derived from corn stalks were tested. Respectively, the IRS and traditional K-means algorithms were used for image segmentation to the in-situ three-dimensional (3D) visual characterization of the Cu(II) adsorption onto biochar. The results indicated that the IRS algorithm reduced interference from high-density biochar composition, and thus achieved more precise results (R2 = 0.95) than that of K-means (R2 = 0.72). The visualized dynamic migration of Cu(II) from surface adsorption to intraparticle diffusion reflexed the complex mechanism of heavy metal adsorption. The developed Micro-CT method with high generalizability has great potential for studying the process and mechanism of biochar heavy metal adsorption.

Solar reduced graphene oxide decorated with manganese dioxide nanostructures for brackish water desalination using asymmetric capacitive deionization

Capacitive deionization (CDI) has emerged as a low-cost, reagent-free technique for the desalination of water. This technique is based on the immobilization of dissolved ions on the electrically charged electrodes, by the electrosorption phenomenon. The electrosorption of dissolved ions by using CDI is limited for feed water having a low concentration of salts. To address this problem, we employ an asymmetric capacitive deionization (Asy-CDI) architecture having solar reduced graphene oxide decorated with manganese dioxide nanostructures (SRGO-MnO2 composite). The Asy-CDI possesses an SRGO-MnO2 composite as the cathode and SRGO as the anode with an anion exchange membrane. The cathode formed from the SRGO-MnO2 composite serves the purpose of immobilization of cations, whereas the anode formed from SRGO is responsible for anion removal. The crystal structure, chemical composition and morphology of the as-synthesized SRGO-MnO2 composite electrode materials are characterized by several techniques, confirming that the surface of SRGO is successfully loaded with α-MnO2 nanostructures. The electrochemical characterization reveals a high specific capacitance of the as-synthesized SRGO-MnO2 composite (419.9 F g-1) at 100 mV s-1. The Asy-CDI provides a higher salt adsorption capacity (40.2 mg g-1) compared to Sy-CDI (28.3 mg g-1) with feed water containing a salt concentration of 2000 mg L-1. These results indicate that the Asy-CDI may be employed as an efficient technique for the desalination of high concentration salt water.