A pilot study on the design and validation of a hybrid exoskeleton robotic device for hand rehabilitation

Design, modeling, and preliminary evaluation of a simple wrist-hand stretching orthosis for neurologically impaired patients

This work studies upper-limb impairment resulting from stroke or traumatic brain injury and presents a simple technological solution for a subset of patients: a soft, active stretching aid for at-home use. To better understand the issues associated with existing associated rehabilitation devices, customer discovery conversations were conducted with 153 people in the healthcare ecosystem (60 patients, 30 caregivers, and 63 medical providers). These patients fell into two populations: spastic (stiff, clenched hands) and flaccid (limp hands). Focusing on the first category, a set of design constraints was developed based on the information collected from the customer discovery. With these constraints in mind, a powered wrist-hand stretching orthosis (exoskeleton) was designed and prototyped as a preclinical study (T0 basic science research) to aid in recovery. The orthosis was tested on two patients for proof-of-concept, one survivor of stroke and one of traumatic brain injury. The prototype was able to consistently open both patients' hands. A mathematical model was developed to characterize joint stiffness based on experimental testing. Donning and doffing times for the prototype averaged 76 and 12.5 s, respectively, for each subject unassisted. This compared favorably to times shown in the literature. This device benefits from simple construction and low-cost materials and is envisioned to become a therapy device accessible to patients in the home. This work lays the foundation for phase 1 clinical trials and further device development.

The Design and Adaptive Control of a Parallel Chambered Pneumatic Muscle-Driven Soft Hand Robot for Grasping Rehabilitation

The widespread application of exoskeletons driven by soft actuators in motion assistance and medical rehabilitation has proven effective for patients who struggle with precise object grasping and suffer from insufficient hand strength due to strokes or other conditions. Repetitive passive flexion/extension exercises and active grasp training are known to aid in the restoration of motor nerve function. However, conventional pneumatic artificial muscles (PAMs) used for hand rehabilitation typically allow for bending in only one direction, thereby limiting multi-degree-of-freedom movements. Moreover, establishing precise models for PAMs is challenging, making accurate control difficult to achieve. To address these challenges, we explored the design and fabrication of a bidirectionally bending PAM. The design parameters were optimized based on actual rehabilitation needs and a finite element analysis. Additionally, a dynamic model for the PAM was established using elastic strain energy and the Lagrange equation. Building on this, an adaptive position control method employing a radial basis function neural network, optimized for parameters and hidden layer nodes, was developed to enhance the accuracy of these soft PAMs in assisting patients with hand grasping. Finally, a wearable soft hand rehabilitation exoskeleton was designed, offering two modes, passive training and active grasp, aimed at helping patients regain their grasp ability.

Design, modeling, and preliminary evaluation of a 3D-printed wrist-hand grasping orthosis for stroke survivors

Stroke causes neurological and physical impairment in millions of people around the world every year. To better comprehend the upper-limb needs and challenges stroke survivors face and the issues associated with existing technology and formulate ideas for a technological solution, the authors conversed with 153 members of the ecosystem (60 neuro patients, 30 caregivers, and 63 medical providers). Patients fell into two populations depending on their upper-limb impairment: spastic (stiff, clenched hands) and flaccid (limp hands). For this work, the authors chose to focus on the second category and developed a set of design constraints based on the information collected through customer discovery. With these in mind, they designed and prototyped a 3D-printed powered wrist-hand grasping orthosis (exoskeleton) to aid in recovery. The orthosis is easily custom-sized based on two parameters and derived anatomical relationships. The researchers tested the prototype on a survivor of stroke and modeled the kinematic behavior of the orthosis with and without load. The prototype neared or exceeded the target design constraints and was able to grasp objects consistently and stably, as well as exercise the patients' hands. In particular, donning time was only 42 s, as compared to the next fastest time of 3 min reported in literature. This device has the potential for effective neurorehabilitation in a home setting, and it lays the foundation for clinical trials and further device development.

Modular soft pneumatic actuator mimics elephant trunk locomotion

Robots support and facilitate tasks in all life fields. Soft robots specifically have the advantages of inherent compliance, safe interaction and flexible deformability. Soft pneumatic network (Pneu-Net) is a soft pneumatic actuator (SPA) composed of network of chambers that is actuated by pneumatic power. Soft Pneu-Net fits the human interface applications perfectly. In this paper, a bio-inspired modular based design for Pneu-Net actuator is developed. The actuator mimics the elephant trunk curling to be employed for rehabilitation of human hand fingers. The actuator is an integrated four Pneu-Net modules actuator which is attached to hand's finger. The main introduced advantages in the new developed actuator are: providing four degrees of freedom (DoF) essential for finger's motion by single compound actuator and developing a methodology for a modular soft Pneu-Net actuator that is efficiently reproducible. The actuator's design is developed using computer aided design (CAD) software SOLIDWORKS. The design is simulated using finite element modeling (FEM) software ABAQUS. Fabrication process uses 3D printed molds. Soft material is molded in the 3D printed molds, forming actuator's modules. Actuator's modules are integrated by adhesion using the soft material. A proposed non-standard hyper-elastic material biaxial tension test is introduced as a quick material properties identification method that can produce a test table used for material identification in the FEM. Enhanced version for the actuator uses reinforcement fibers. Results show advances for the reinforced actuator, as it limits the unwanted actuator's strain and deformation. The reinforced actuator shows improved energy efficiency reaches to 46%.

Modeling multi-contact point physical interaction between the anthropomorphic finger and soft robotic exo-digit for wearable rehabilitation robotics applications

Introduction: Effective control of rehabilitation robots requires considering the distributed and multi-contact point physical human-robot interaction and users' biomechanical variation. This paper presents a quasi-static model for the motion of a soft robotic exo-digit while physically interacting with an anthropomorphic finger model for physical therapy. Methods: Quasi-static analytical models were developed for modeling the motion of the soft robot, the anthropomorphic finger, and their coupled physical interaction. An intertwining of kinematics and quasi-static motion was studied to model the distributed (multiple contact points) interaction between the robot and a human finger model. The anthropomorphic finger was modeled as an articulated multi-rigid body structure with multi-contact point interaction. The soft robot was modeled as an articulated hybrid soft-and-rigid model with a constant bending curvature and a constant length for each soft segment. A hyperelastic constitute model based on Yeoh's 3rdorder material model was used for modeling the soft elastomer. The developed models were experimentally evaluated for 1) free motion of individual soft actuators and 2) constrained motion of the soft robotic exo-digit and anthropomorphic finger model. Results and Discussion: Simulation and experimental results were compared for performance evaluations. The theoretical and experimental results were in agreement for free motion, and the deviation from the constrained motion was in the range of the experimental errors. The outcomes also provided an insight into the importance of considering lengthening for the soft actuators.

Exo Supportive Devices: Summary of Technical Aspects

Human societies have been trying to mitigate the suffering of individuals with physical impairments, with a special effort in the last century. In the 1950s, a new concept arose, finding similarities between animal exoskeletons, and with the goal of medically aiding human movement (for rehabilitation applications). There have been several studies on using exosuits with this purpose in mind. So, the current review offers a critical perspective and a detailed analysis of the steps and key decisions involved in the conception of an exoskeleton. Choices such as design aspects, base materials (structure), actuators (force and motion), energy sources (actuation), and control systems will be discussed, pointing out their advantages and disadvantages. Moreover, examples of exosuits (full-body, upper-body, and lower-body devices) will be presented and described, including their use cases and outcomes. The future of exoskeletons as possible assisted movement solutions will be discussed-pointing to the best options for rehabilitation.

Soft Robotics: A Systematic Review and Bibliometric Analysis

In recent years, soft robotics has developed considerably, especially since the year 2018 when it became a hot field among current research topics. The attention that this field receives from researchers and the public is marked by the substantial increase in both the quantity and the quality of scientific publications. In this review, in order to create a relevant and comprehensive picture of this field both quantitatively and qualitatively, the paper approaches two directions. The first direction is centered on a bibliometric analysis focused on the period 2008-2022 with the exact expression that best characterizes this field, which is "Soft Robotics", and the data were taken from a series of multidisciplinary databases and a specialized journal. The second direction focuses on the analysis of bibliographic references that were rigorously selected following a clear methodology based on a series of inclusion and exclusion criteria. After the selection of bibliographic sources, 111 papers were part of the final analysis, which have been analyzed in detail considering three different perspectives: one related to the design principle (biologically inspired soft robotics), one related to functionality (closed/open-loop control), and one from a biomedical applications perspective.

Recent advancements in digital health management using multi-modal signal monitoring

Healthcare is the method of keeping or enhancing physical and mental well-being with its aid of illness and injury prevention, diagnosis, and treatment. The majority of conventional healthcare practices involve manual management and upkeep of client demographic information, case histories, diagnoses, medications, invoicing, and drug stock upkeep, which can result in human errors that have an impact on clients. By linking all the essential parameter monitoring equipment through a network with a decision-support system, digital health management based on Internet of Things (IoT) eliminates human errors and aids the doctor in making more accurate and timely diagnoses. The term "Internet of Medical Things" (IoMT) refers to medical devices that have the ability to communicate data over a network without requiring human-to-human or human-to-computer interaction. Meanwhile, more effective monitoring gadgets have been made due to the technology advancements, and these devices can typically record a few physiological signals simultaneously, including the electrocardiogram (ECG) signal, the electroglottography (EGG) signal, the electroencephalogram (EEG) signal, and the electrooculogram (EOG) signal. Yet, there has not been much research on the connection between digital health management and multi-modal signal monitoring. To bridge the gap, this article reviews the latest advancements in digital health management using multi-modal signal monitoring. Specifically, three digital health processes, namely, lower-limb data collection, statistical analysis of lower-limb data, and lower-limb rehabilitation via digital health management, are covered in this article, with the aim to fully review the current application of digital health technology in lower-limb symptom recovery.

Autonomous Exercise Generator for Upper Extremity Rehabilitation: A Fuzzy-Logic-Based Approach

In this paper, an autonomous exercise generation system based of fuzzy logic approach is presented. This work attempts to close a gap in the design of a completely autonomous robotic rehabilitation system that can recommend exercises to patients based on their data, such as shoulder range of motion (ROM) and muscle strength, from a pre-set library of exercises. The input parameters are fed into a system that uses Mamdani-style fuzzy logic rules to process them. In medical applications, the rationale behind decision making is a sophisticated process that involves a certain amount of uncertainty and ambiguity. In this instance, a fuzzy-logic-based system emerges as a viable option for dealing with the uncertainty. The system's rules have been reviewed by a therapist to ensure that it adheres to the relevant healthcare standards. Moreover, the system has been tested with a series of test data and the results obtained ensures the proposed idea's feasibility.

Design, modeling and control of an index finger exoskeleton for rehabilitation

With diverse areas of applications, wearable robotic exoskeleton devices have gained attention in the past decade. These devices cover one or more human limbs/joints and have been presented for rehabilitation, strength augmentation and interaction with virtual reality. This research is focused towards design, modeling and control of a novel series elastic actuation (SEA) based index finger exoskeleton with a targeted torque rendering capability of 0.3 Nm and a force control bandwidth of 3 Hz. The proposed design preserves the natural range of motion of the finger by incorporating five passive and two actively actuated joints and provides active control of metacarpophalangeal and proximal interphalangeal joints. Forward and inverse kinematics for both position and velocity have been solved using closed loop vector analysis by including human finger as an integral part of the system. For accurate force control, a cascaded control structure has been presented. Force controlled trajectories have been proposed to guide the finger along preprogrammed virtual paths. Such trajectories serve to gently guide the finger towards the correct rehabilitation protocol, thus acting as an effective replacement of intervention by a human therapist. Extensive computer simulations have been performed before fabricating a prototype and performing experimental validation. Results show accurate modeling and control of the proposed design.

Clinical utility of a pediatric hand exoskeleton: identifying users, practicability, and acceptance, and recommendations for design improvement

BACKGROUND

Children and adolescents with upper limb impairments can experience limited bimanual performance reducing daily-life independence. We have developed a fully wearable pediatric hand exoskeleton (PEXO) to train or compensate for impaired hand function. In this study, we investigated its appropriateness, practicability, and acceptability.

METHODS

Children and adolescents aged 6-18 years with functional limitations in at least one hand due to a neurological cause were selected for this cross-sectional evaluation. We characterized participants by various clinical tests and quantified bimanual performance with the Assisting Hand Assessment (AHA). We identified children whose AHA scaled score increased by ≥ 7 points when using the hand exoskeleton and determined clinical predictors to investigate appropriateness. The time needed to don each component and the number of technical issues were recorded to evaluate practicability. For acceptability, the experiences of the patients and the therapist with PEXO were evaluated. We further noted any adverse events.

RESULTS

Eleven children (median age 11.4 years) agreed to participate, but data was available for nine participants. The median AHA scaled score was higher with PEXO (68; IQR: 59.5-83) than without (55; IQR: 37.5-80.5; p = 0.035). The Box and Block test, the Selective Control of the Upper Extremity Scale, and finger extensor muscle strength could differentiate well between those participants who improved in AHA scaled scores by ≥ 7 points and those who did not (sensitivity and specificity varied between 0.75 and 1.00). The median times needed to don the back module, the glove, and the hand module were 62, 150, and 160 s, respectively, but all participants needed assistance. The most critical failures were the robustness of the transmission system, the electronics, and the attachment system. Acceptance was generally high, particularly in participants who improved bimanual performance with PEXO. Five participants experienced some pressure points. No adverse events occurred.

CONCLUSIONS

PEXO is a safe exoskeleton that can improve bimanual hand performance in young patients with minimal hand function. PEXO receives high acceptance. We formulated recommendations to improve technical issues and the donning before such exoskeletons can be used under daily-life conditions for therapy or as an assistive device. Trial registration Not appropriate.

Synergistic Immediate Cortical Activation on Mirror Visual Feedback Combined With a Soft Robotic Bilateral Hand Rehabilitation System: A Functional Near Infrared Spectroscopy Study

Background

Mirror visual feedback (MVF) has been widely used in neurological rehabilitation. Due to the potential gain effect of the MVF combination therapy, the related mechanisms still need be further analyzed.

Methods

Our self-controlled study recruited 20 healthy subjects (age 22.150 ± 2.661 years) were asked to perform four different visual feedback tasks with simultaneous functional near infrared spectroscopy (fNIRS) monitoring. The right hand of the subjects was set as the active hand (performing active movement), and the left hand was set as the observation hand (static or performing passive movement under soft robotic bilateral hand rehabilitation system). The four VF tasks were designed as RVF Task (real visual feedback task), MVF task (mirror visual feedback task), BRM task (bilateral robotic movement task), and MVF + BRM task (Mirror visual feedback combined with bilateral robotic movement task).

Results

The beta value of the right pre-motor cortex (PMC) of MVF task was significantly higher than the RVF task (RVF task: -0.015 ± 0.029, MVF task: 0.011 ± 0.033, P = 0.033). The beta value right primary sensorimotor cortex (SM1) in MVF + BRM task was significantly higher than MVF task (MVF task: 0.006 ± 0.040, MVF + BRM task: 0.037 ± 0.036, P = 0.016).

Conclusion

Our study used the synchronous fNIRS to compare the immediate hemodynamics cortical activation of four visual feedback tasks in healthy subjects. The results showed the synergistic gain effect on cortical activation from MVF combined with a soft robotic bilateral hand rehabilitation system for the first time, which could be used to guide the clinical application and the future studies.

Modeling and Evaluation of a Novel Hybrid-Driven Compliant Hand Exoskeleton Based on Human-Machine Coupling Model

This paper presents the modeling design method for a novel hybrid-driven compliant hand exoskeleton based on the human-machine coupling model for the patients who have requirements on training and assisting. Firstly, the human-machine coupling model is established based on the kinematics characteristics of human fingers and the Bernoulli beam formula. On this basis, the variable stiffness flexible hinge (VSFH) is used to drive the finger extension and the cable-driven mechanism is used to implement the movement of the finger flexion. Here, a hand orthosis is designed in the proposed hand exoskeleton to act as the base and maintain the function position of the hand for patients with hand dysfunction. Then, a final design prototype is fabricated to evaluate the proposed modeling method. In the end, a series of experiments based on the prototype is proceeded to evaluate its capabilities on stretching force for extension, bio-imitability, finger flexion capability, and fingertip force. The results show that the prototype has a significant improvement in all aspects of the ability mentioned above, and has good bionics. The proposed design method can be utilized to implement the rapid design of the hybrid-driven compliant hand exoskeleton with the changed requirements. The novel modeling method can be easily applied in personalized design in rehabilitation engineering.

Design of a variable stiffness index finger exoskeleton

This paper presents the design and experimentation of a variable stiffness index finger exoskeleton consisting of four-bar mechanisms actuated by a linear actuator. The lengths of the four-bar mechanism were optimized so that it can follow a recorded index fingertip trajectory. The mechanism has a fixed compliance at the coupler of the four-bar link and a variable compliance at the linear actuator that moves the four-bar. The skeletal shape of the coupler of the finger link has been optimized using FEM. The exoskeleton can apply a constant fingertip force irrespective of the position of the fingers.

Development of a Low-Cost EEG-Controlled Hand Exoskeleton 3D Printed on Textiles

Stroke survivors can be affected by motor deficits in the hand. Robotic equipment associated with brain–machine interfaces (BMI) may aid the motor rehabilitation of these patients. BMIs involving orthotic control by motor imagery practices have been successful in restoring stroke patients' movements. However, there is still little acceptance of the robotic devices available, either by patients and clinicians, mainly because of the high costs involved. Motivated by this context, this work aims to design and construct the Hand Exoskeleton for Rehabilitation Objectives (HERO) to recover extension and flexion movements of the fingers. A three-dimensional (3D) printing technique in association with textiles was used to produce a lightweight and wearable device. 3D-printed actuators have also been designed to reduce equipment costs. The actuator transforms the torque of DC motors into linear force transmitted by Bowden cables to move the fingers passively. The exoskeleton was controlled by neuroelectric signal—electroencephalography (EEG). Concept tests were performed to evaluate control performance. A healthy volunteer was submitted to a training session with the exoskeleton, according to the Graz-BCI protocol. Ergonomy was evaluated with a two-dimensional (2D) tracking software and correlation analysis. HERO can be compared to ordinary clothing. The weight over the hand was around 102 g. The participant was able to control the exoskeleton with a classification accuracy of 91.5%. HERO project resulted in a lightweight, simple, portable, ergonomic, and low-cost device. Its use is not restricted to a clinical setting. Thus, users will be able to execute motor training with the HERO at hospitals, rehabilitation clinics, and at home, increasing the rehabilitation intervention time. This may support motor rehabilitation and improve stroke survivors life quality.