Biomechanical response of a novel intervertebral disc prosthesis using functionally graded polymers: A finite element study

Overloading effect on the osmo-viscoelastic and recovery behavior of the intervertebral disc

In vitro studies investigating the effect of high physiological compressive loads on the intervertebral disc mechanics as well as on its recovery are rare. Moreover, the osmolarity effect on the disc viscoelastic behavior following an overloading is far from being studied. This study aims to determine whether a compressive loading-unloading cycle exceeding physiological limits could be detrimental to the cervical disc, and to examine the chemo-mechanical dependence of this overloading effect. Cervical functional spine units were subjected to a compressive loading-unloading cycle at a high physiological level (displacement of 2.5 mm). The overloading effect on the disc viscoelastic behavior was evaluated through two relaxation tests conducted before and after cyclic loading. Afterward, the disc was unloaded in a saline bath during a rest period, and its recovery response was assessed by a third relaxation test. The chemo-mechanical coupling in the disc response was further examined by repeating this protocol with three different saline concentrations in the external fluid bath. It was found that overloading significantly alters the disc viscoelastic response, with changes statistically dependent on osmolarity conditions. The applied hyper-physiological compressive cycle does not cause damage since the disc recovers its original viscoelastic behavior following a rest period. Osmotic loading only influences the loading-unloading response; specifically, increasing fluid osmolarity leads to a decrease in disc relaxation after the applied cycle. However, the disc recovery is not impacted by the osmolarity of the external fluid.

Finite element modeling to predict the influence of anatomic variation and implant placement on performance of biological intervertebral disc implants

Background

Tissue-engineered intervertebral disc (TE-IVD) constructs are an attractive therapy for treating degenerative disc disease and have previously been investigated in vivo in both large and small animal models. The mechanical environment of the spine is notably challenging, in part due to its complex anatomy, and implants may require additional mechanical support to avoid failure in the early stages of implantation. As such, the design of suitable support implants requires rigorous validation.

Methods

We created a FE model to simulate the behavior of the IVD cages under compression specific to the anatomy of the porcine cervical spine, validated the FE model using an animal model, and predicted the effects of implant location and vertebral angle of the motion segment on implant behavior. Specifically, we tested anatomical positioning of the superior vertebra and placement of the implant. We analyzed corresponding stress and strain distributions.

Results

Results demonstrated that the anatomical geometry of the porcine cervical spine led to concentrated stress and strain on the posterior side of the cage. This stress concentration was associated with the location of failure of the cages reported in vivo, despite superior mechanical properties of the implant. Furthermore, placement of the cage was found to have profound effects on migration, while the angle of the superior vertebra affected stress concentration of the cage.

Conclusions

This model can be utilized both to inform surgical procedures and provide insight on future cage designs and can be adopted to models without the use of in vivo animal models.

Stress-dependent design and optimization methodology of gradient porous implant and application in femoral stem

Gradient porous structure made by additive manufacturing (AM) technology is potential to improve the long-term stability of orthopaedic implants through bone ingrowth while maintaining mechanical safety. In this study, a parametrical optimization methodology for the customized gradient porous implants was developed based on a stress-dependent design algorithm. Clinical requirements and manufacturing capabilities of AM were considered in the design procedure. A femoral stem with a minimum bone loss proportion of 2.4% by optimizing the control parameters. This study provided a feasible and flexible design approach for the customized implant with gradient porous structure or material components.

Osmo-inelastic response of the intervertebral disc annulus fibrosus tissue

The aim of this article is to provide some insights on the osmo-inelastic response under stretching of annulus fibrosus of the intervertebral disc. Circumferentially oriented specimens of square cross section, extracted from different regions of bovine cervical discs (ventral-lateral and dorsal-lateral), are tested under different strain-rates and saline concentrations within normal range of strains. An accurate optical strain measuring technique, based upon digital image correlation, is used in order to determine the full-field displacements in the lamellae and fibers planes of the layered soft tissue. Annulus stress-stretch relationships are measured along with full-field transversal strains in the two planes. The mechanical response is found hysteretic, rate-dependent and osmolarity-dependent with a Poisson's ratio higher than 0.5 in the fibers plane and negative (auxeticity) in the lamellae plane. While the stiffness presents a regional-dependency due to variations in collagen fibers content/orientation, the strain-rate sensitivity of the response is found independent on the region. A significant osmotic effect is found on both the auxetic response in the lamellae plane and the stiffness rate-sensitivity. These local experimental observations will result in more accurate chemo-mechanical modeling of the disc annulus and a clearer multi-scale understanding of the disc intervertebral function.