The influence of gap size on the development of fracture union with a micro external fixator

Development of a novel rat long-bone nonunion model and efficacy evaluation of a prostaglandin EP4 selective agonist (AKDS001) combined with iliac bone grafting

Aims

Nonunion occurs when a fracture fails to heal permanently, often necessitating surgical intervention to stimulate the bone healing response. Current animal models of long-bone nonunion do not adequately replicate human pathological conditions. This study was intended as a preliminary investigation of a novel rat nonunion model using a two-stage surgical intervention, and to evaluate the efficacy of a selective prostaglandin E2 receptor 4 agonist (AKDS001) as a novel nonunion therapeutic agent compared with existing treatments.

Methods

Initially, Sprague-Dawley rats underwent intramedullary Kirschner wire (K-wire) fixation of a femoral fracture with the interposition of a 2 mm-thick silicon disc. After three weeks, the silicon disc was removed, and the intramedullary K-wire was replaced with plate fixation while maintaining the 2 mm defect. Contrary to the control group (1) that received no treatment, the following therapeutic interventions were performed at injury sites after freshening: (2) freshening group: no grafting; (3) iliac bone (IB) group: IB grafting; (4) AKDS group: AKDS001-loaded microspheres (MS) combined with IB (0.75 mg/ml); and (5) bone morphogenetic protein (BMP) group: grafting of a BMP-2-loaded collagen sponge (10 μg; 0.10 mg/ml). After six weeks, micro-CT (μCT) and histological analysis was performed.

Results

In the control group, the radiological union rate was 0%, and histological findings showed that fracture sites comprised fibrous scar tissue, resembling the histology of human nonunion. The union rates in the freshening, IB, AKDS, and BMP groups were 16.7%, 0%, 62.5%, and 50.0%, respectively. The AKDS group demonstrated a significantly higher union rate than the IB group (p = 0.026). μCT and histological analysis indicated that the quality of newly formed bone was superior in the AKDS group than in the BMP group.

Conclusion

We developed a novel long-bone nonunion model. The co-therapy of AKDS001-MS and IB grafting presents a promising new treatment for nonunion.

Does protruding headless cannulated screw reduce fixation stability in tension band wiring technique for patella fractures? a biomechanical study

BACKGROUND

The selection of an implant is a critical factor in the surgical treatment of patella fractures due to the risk of various complications, such as non-union, implant failure, and irritation. The present study evaluated and compared the biomechanical strength of headless cannulated screws about screw length using the tension band wiring technique.

METHODS

Forty-eight sawbone patellas with transverse fractures were divided into three fixation groups based on the screw length used in tension band wiring. Overall, three different fixation groups were determined: Group 1 (recessed headless cannulated screw fixation), Group 2 (full-length headless cannulated screw fixation), and Group 3 (protruding headless cannulated screw fixation). A setup was used to simulate a knee with a flexion angle of 60 degrees. Specimens underwent biomechanical testing under axial traction (static test) and cyclic loading (dynamic test). Displacements at 300 Newtons (N), loads at 2 millimetres (mm) displacement, and failure loads were documented for each sample in the static test. In the dynamic test protocol, 10,000 repetitive cycles were performed under physiological load between 100 and 300 N, and final displacements were recorded.

RESULTS

There were significant differences in the loads achieved at 2 mm displacement levels, and Group 3 demonstrated lower force values compared to other constructs in the static test (P = 0.003). All groups revealed similar displacements at 300 N and failure load values under axial traction. In the dynamic test, Group 3 had significantly higher fracture displacement under cyclic loading compared to the other specimens (P = 0.006).

CONCLUSIONS

This study found headless cannulated screws for transverse patella fracture fixation provide sufficient stability; however, protruding headless screws reduce the fixation strength. Recessed or full-length screws may improve stability and bony healing, potentially preventing complications in patella fractures.

LEVEL OF EVIDENCE

Biomechanical study N/A.

Unilateral external fixator and its biomechanical effects in treating different types of femoral fracture: A finite element study with experimental validated model

Previous works had successfully demonstrated the clinical effectiveness of unilateral external fixator in treating various types of fracture, ranging from the simple type, such as oblique and transverse fractures, to complex fractures. However, literature that investigated its biomechanical analyses to further justify its efficacy is limited. Therefore, this paper aimed to analyse the stability of unilateral external fixator for treating different types of fracture, including the simple oblique, AO32C3 comminuted, and 20 mm gap transverse fracture. These fractures were reconstructed at the distal diaphysis of the femoral bone and computationally analysed through the finite element method under the stance phase condition. Findings showed a decrease in the fixation stiffness in large gap fracture (645.2 Nmm-1 for oblique and comminuted, while 23.4 Nmm-1 for the gap fracture), which resulted in higher displacement, IFM and stress distribution at the pin bone interface. These unfavourable conditions could consequently increase the risk of delayed union, pin loosening and infection, as well as implant failure. Nevertheless, the stress observed on the fracture surfaces was relatively low and in controlled amount, indicating that bone unity is still allowable in all models. Briefly, the unilateral fixation may provide desirable results in smaller fracture gap, but its usage in larger gap fracture might be alarming. These findings could serve as a guide and insight for surgeons and researchers, especially on the biomechanical stability of fixation in different fracture types and how will it affect bone unity.

The value of bone SPECT/CT in evaluation of foot and ankle arthrodesis and adjacent joint secondary osteoarthritis

OBJECTIVE

To evaluate the value of SPECT/CT (single photon emission computed tomography/computed tomography) in foot and ankle arthrodesis and development of secondary osteoarthritis in the adjacent joints.

MATERIALS AND METHODS

SPECT/CT of 140 joints in the foot and ankle (34 upper ankle (UA), 28 lower ankle (LA), 27 talonavicular (TN), 12 calcaneo-cuboidal (CC), and 39 other smaller joints after arthrodesis in 72 patients were evaluated retrospectively regarding fusion grade in CT (0 = no fusion, 1 =  < 50% fusion, 2 =  > 50% fusion, 3 = complete fusion) and radiotracer uptake (0 = no uptake, 1 = mild uptake, 2 = moderate uptake, 3 = high uptake) on SPECT/CT. Severity of osteoarthritis (1 = mild, 2 = moderate, 3 = severe) and radiotracer uptake grade in adjacent joints was also assessed. In 54 patients, clinical information about interventions in the follow-up was available.

RESULTS

According to the SPECT/CT, arthrodesis was successful (grade 2 or 3 CT fusion and grade 0 or 1 uptake) in 73% (25/34) of UA joints, 71% (20/28) of LA joints, 67% (18/27) TN, 100% (12/12) CC joints, and 62% (24/39) of other smaller joints. In 12 joints, there were discrepant findings in SPECT/CT (fusion grade 2 and uptake grade 2 or 3 (n = 9); or, fusion grade 0 or 1 and uptake grade 1 (n = 3)). The fusion rate 6-12 months after arthrodesis was 42% (14/33), 59% (20/34) after 13-24 months, and 89% (65/73) after more than 24 months, respectively. Average radiotracer uptake in arthrodesis decreased with age: 6-12 months: 1.60, 12-24 months: 1.32,  > 24 months: 0.38. There was a significant negative correlation between radiotracer uptake grade and CT fusion grade. Osteoarthritis was observed in 131 adjacent joints. During the post scan follow-up, additional arthrodeses were performed in 33 joints, of which 11 joints were re-arthrodesis and 22 were new arthrodeses in osteoarthritic adjacent joints. All these 11 joints with failed arthrodesis had grade 0 of CT fusion and grade 2 or 3 of radiotracer uptake. All 22 adjacent joints with osteoarthritis, which subsequently underwent arthrodesis, had grade 2 or 3 radiotracer uptake, and the primary arthrodesis joints were healed and fused in all these cases.

CONCLUSION

Bone SPECT/CT is a valuable hybrid imaging tool in the evaluation of foot and ankle arthrodesis and gives additional useful information about the development of secondary osteoarthritis in the adjacent joints with higher value for the assessment of secondary osteoarthritis. A practical four-type classification ('Lucerne Criteria') combining metabolic and morphologic SPECT/CT information for evaluation of arthrodesis joints has been proposed.

Fracture healing in a polytrauma rat model is influenced by mtDNA:cGAS complex mediated pro-inflammation

PURPOSE

The mitochondrial DNA (mtDNA) activated cyclic guanosine monophosphate-adenosine monophosphate synthase-stimulator of interferon genes (cGAS-STING) signaling pathway is a key player in mediating immune responses in autoimmune disorders and cancer. However, its role in severe trauma associated fracture healing is unknown. This study investigated if the cGAS-STING signaling pathway contributes to delayed bone healing in polytrauma (PT) fractures.

METHODS

For preliminary analyses, therapeutic dosage of RU.521 (cGAS inhibitor) (n = 2) was determined in C57BL/6 J mice by mass spectrometry, and IFNβ expression levels in serum and bronchioalveolar fluid (BALF) at 6 and 24 h (h) in RU.521/vehicle + mtDNA injected mice (n = 3/treatment and time point) was measured by ELISA. In the main study, plasma mtDNA was quantified by qPCR in a clinically relevant delayed fracture healing PT rat model with burn injury, blunt trauma, and a femoral fracture at 3 h post-trauma (hpt). Next, PT rats received either RU.521 (12 mg/kg in povidone; n = 8) or vehicle (povidone only; n = 5) immediately after injury and were followed up for 5 weeks post-trauma to assess bone regeneration by radiography and histology.

RESULTS

IFNβ levels were significantly decreased only at 24 h in BALF of RU.521 treated mice. At 3hpt mtDNA was significantly elevated in PT rats compared to rats without injury. When treated with RU.521, PT rats showed improvement in bone healing compared to vehicle control PT rats.

CONCLUSIONS

These data reveal that the cGAS-STING signaling pathway influences trauma-induced delayed bone healing. However, further evaluation of this pathway at the cellular and molecular levels to augment PT associated detrimental effects is needed.

Effect of fracture level on the residual fracture gap during tibial intramedullary nailing for tibial shaft fractures

INTRODUCTION

The development of fracture gap during intramedullary nailing in tibial fractures is associated with poor fracture fragment contact and increased time to union and complications. This study aimed to evaluate the effect of the fracture level in the development of the fracture gap and the effect of the fracture gap on pain, radiologic and functional outcomes, and complication rate.

MATERIAL AND METHOD

A total of 45 patients who underwent reamed intramedullary nailing due to closed transverse or short oblique tibial shaft fractures were divided into the proximal fracture group and the distal fracture group. The correlations between the visual analog scale (VAS) score, modified radiograph union score for tibias (RUST), and postoperative 1-year lower extremity functional scale scores, residual fracture gap, and time to union were evaluated.

RESULTS

The mean fracture gap amounts in the immediate postoperative anteroposterior and lateral radiographs were 5.6 ± 1.7 and 6.0 ± 1.7 mm in proximal fractures and 0.3 ± 2.4 mm and 0.4 ± 2.3 mm in distal fractures, respectively (p < 0.001 and p < 0.001, respectively). The mean time to union was 21.9 ± 2.9 weeks in the proximal fracture group and 16.7 ± 2.4 weeks in the distal fracture group (p < 0.000). The residual fracture gap amount significantly correlated with the level of fracture (r = 0.811, p < 0.001).

DISCUSSION

Tibial shaft fractures proximal to the isthmus level tend to develop significantly larger fracture gaps than distal fractures. It is associated with increased time to union and radiographic union scores as well as slightly higher complication and reoperation rates.

Uncovertebral Joint Fusion Versus End Plate Space Fusion in Anterior Cervical Spine Surgery: A Prospective Randomized Controlled Trial

BACKGROUND

The uncovertebral joint is a potential region for anterior cervical fusion. Currently, we are aware of no clinical trials on human uncovertebral joint fusion (UJF). The purpose of this study was to compare the time it took to achieve osseous union/fusion and the clinical efficacy of UJF to end plate space fusion (ESF)-i.e., traditional anterior cervical discectomy and fusion (ACDF)-in anterior cervical surgery.

METHODS

Patients with single-level cervical spondylosis were recruited from April 2021 through October 2022 and randomly divided into the UJF and ESF groups, with 40 patients in each group. Autologous iliac bone was used for bone grafting in both groups. The primary outcome was the early fusion rate at 3 months postoperatively. Secondary outcomes included the prevalence of complications and patient-reported outcome measures (PROMs), including the Japanese Orthopaedic Association (JOA) score, Neck Disability Index (NDI), and visual analog scale (VAS) scores for arm and neck pain.

RESULTS

A total of 74 patients (92.5%) with an average age of 49.8 years (range, 26 to 65 years) completed the trial and were included in the analysis. There was no significant difference between the 2 groups at baseline. The operative duration and intraoperative blood loss were also comparable between the 2 groups. The fusion rate in the UJF group was significantly higher than that in the ESF group at 3 months (66.7% compared with 13.2%, p < 0.0001) and 6 months (94.1% compared with 66.7%, p = 0.006) after the operation. No significant difference was found in the fusion rate between the 2 groups 12 months postoperatively. Overall, the PROMs significantly improved after surgery in both groups and did not differ significantly between the groups at any follow-up time point. The prevalence of complications was not significantly different between the 2 groups.

CONCLUSIONS

In our study of anterior cervical fusion surgery, we found that the early fusion rate after UJF was significantly higher than that after ESF.

LEVEL OF EVIDENCE

Therapeutic Level I . See Instructions for Authors for a complete description of levels of evidence.

A new method for segmentation and analysis of bone callus in rodent fracture models using micro-CT

Fracture burden has created a need to better understand bone repair processes under different pathophysiological states. Evaluation of structural and material properties of the mineralized callus, which is integral to restoring biomechanical stability is, therefore, vital. Microcomputed tomography (micro-CT) can facilitate noninvasive imaging of fracture repair, however, current methods for callus segmentation are only semiautomated, restricted to defined regions, time/labor intensive, and prone to user variation. Herein, we share a new automatic method for segmenting callus in micro-CT tomograms that will allow for objective, quantitative analysis of the bone fracture microarchitecture. Fractured and nonfractured mouse femurs were scanned and processed by both manual and automated segmentation of fracture callus from cortical bone after which microarchitectural parameters were analyzed. All segmentation and analysis steps were performed using CTAn (Bruker) with automatic segmentation performed using the software's image-processing plugins. Results showed automatic segmentation reliably and consistently segmented callus from cortical bone, demonstrating good agreement with manual methods with low bias: tissue volume (TV): -0.320 mm3 , bone volume (BV): 0.0358 mm3 , and bone volume/tissue volume (BV/TV): -3.52%, and was faster and eliminated user-bias and variation. Method scalability and translatability across rodent models were verified in scans of fractured rat femora showing good agreement with manual methods with low bias: TV: -3.654 mm3 , BV: 0.830 mm3 , and BV/TV: 7.81%. Together, these data validate a new automated method for segmentation of callus and cortical bone in micro-CT tomograms that we share as a fast, reliable, and less user-dependent tool for application to study bone callus in fracture, and potentially elsewhere.

Error identification and compensation regarding the kinematic parameter of the MD-PEF for tibial deformity correction

The correction accuracy of an external fixator is crucial to the treatment outcome of deformity correction and patient safety. In this study, the mapping model is established between the pose error and kinematic parameter error of the motor-driven parallel external fixator (MD-PEF). Subsequently, the kinematic parameter identification and error compensation algorithm of the external fixator is established based on the least squares method. An experimental platform based on the developed MD-PEF and Vicon motion capture system is constructed for kinematic calibration experiments. Experimental results show that the correction accuracy of the MD-PEF after calibration is as follows: translation accuracy dE₁ = 0.36 mm, axial translation accuracy dE₂ = 0.25 mm, angulation accuracy dE₃ = 0.27°, and rotation accuracy dE₄ = 0.2°. The accuracy detection experiment verifies the kinematic calibration results, which further validates the feasibility and reliability of the error identification and compensation algorithm constructed by the least squares method. The calibration approach used in this work also provides an effective way to improve the accuracy of other medical robots.

Development of numerical model-based machine learning algorithms for different healing stages of distal radius fracture healing

BACKGROUND AND OBJECTIVES

Early therapeutic exercises are vital for the healing of distal radius fractures (DRFs) treated with the volar locking plate. However, current development of rehabilitation plans using computational simulation is normally time-consuming and requires high computational power. Thus, there is a clear need for developing machine learning (ML) based algorithms that are easy for end-users to implement in daily clinical practice. The purpose of the present study is to develop optimal ML algorithms for designing effective DRF physiotherapy programs at different stages of healing.

METHOD

First, a three-dimensional computational model for the healing of DRF was developed by integrating mechano-regulated cell differentiation, tissue formation and angiogenesis. The model is capable of predicting time-dependant healing outcomes based on different physiologically relevant loading conditions, fracture geometries, gap sizes, and healing time. After being validated using available clinical data, the developed computational model was implemented to generate a total of 3600 clinical data for training the ML models. Finally, the optimal ML algorithm for each healing stage was identified.

RESULTS

The selection of the optimal ML algorithm depends on the healing stage. The results from this study show that cubic support vector machine (SVM) has the best performance in predicting the healing outcomes at the early stage of healing, while trilayered ANN outperforms other ML algorithms in the late stage of healing. The outcomes from the developed optimal ML algorithms indicate that Smith fractures with medium gap sizes could enhance the healing of DRF by inducing larger cartilaginous callus, while Colles fractures with large gap sizes may lead to delayed healing by bringing excessive fibrous tissues.

CONCLUSIONS

ML represents a promising approach for developing efficient and effective patient-specific rehabilitation strategies. However, ML algorithms at different healing stages need to be carefully chosen before being implemented in clinical applications.

General Considerations About Foot and Ankle Arthrodesis. Any Way to Improve Our Results?

Nonunion and adjacent joint osteoarthritis (OA) are known complications after a fusion procedure, and foot and ankle surgeons are commonly exposed to such disabling complications. Determining who is at risk of developing nonunion is essential to reducing nonunion rates and improving patient outcomes. Several evidenced-based modifiable risk factors related to adverse outcomes after foot and ankle arthrodesis have been identified. Patient-related risk factors that can be improved before surgery include smoking cessation, good diabetic control (HbAc1 <7%) and vitamin D supplementation. Intraoperatively, using less invasive techniques, avoiding joint preparation with power tools, using bone grafts or orthobiologics in more complex cases, high-risk patients, nonunion revision surgeries, and filling in bone voids at the arthrodesis site should be considered. Postoperatively, pain management with NSAIDs should be limited to a short period (<2 weeks) and avoided in high-risk patients. Furthermore, early postoperative weight-bearing has shown to be beneficial, and it does not seem to increase postoperative complications. The incidence of surrounding joint OA after foot and ankle fusion seems to increase progressively with time. Owing to its progression and high probability of being symptomatic, patients must be informed consequently, as they may require additional joint fusions, resulting in further loss of ankle/foot motion. In patients with symptomatic adjacent joint OA and unsatisfactory results after an ankle arthrodesis, conversion to total ankle arthroplasty (TAA) has become a potential option in managing these complex and challenging situations.

Medium-Term Outcomes of a Forward-Striking Technique to Reduce Fracture Gaps during Long Cephalomedullary Nailing in Subtrochanteric Femoral Fractures

INTRODUCTION

A residual fracture gap after intramedullary nailing is a known risk factor for delayed union and non-union. This study aimed to report the outcomes of a forward-striking technique to reduce fracture gaps during long cephalomedullary nailing in subtrochanteric femoral fractures (SFFs).

METHODS

A retrospective cohort study was conducted on patients with SFFs treated in a single institution between February 2013 and October 2018. A total of 58 patients treated via long cephalomedullary nailing with a forward-striking technique were included. The width of the fracture gap, location of the cephalic screw, tip-apex distance (TAD), and time to bone union were evaluated using intraoperative and postoperative radiographs. Complication rates, including fixation failure, non-union, implant breakage, and infection, were assessed. The mean follow-up duration was 4 (range, 2‒8) years.

RESULTS

Of the 58 patients (mean age, 67.9 years), 38 (65.5%) were female. Thirty-two cases (55.2%) were classified as atypical femoral fractures. The mean fracture gap reduced from 5.1 mm to 1.6 mm by forward striking (P<0.001). The reduced fracture gap was significantly greater in atypical SFFs (mean, 4.9 mm vs. 1.7 mm; P<0.001). The lag screw was located in the center-center or center-inferior zones of the femoral head in 54 patients (93.1%). The mean TAD was 14.2 mm and was under 25 mm in 55 patients (94.8%). Bone union was achieved in all cases without reoperation at a mean of 5.4 months. One incident of lag screw breakage was noted at 5 months, but bone union was achieved at 7 months.

CONCLUSIONS

The forward-striking technique with a long cephalomedullary nail demonstrated a 100% bone union rate in a consecutive series of 58 SFFs. This technique is effective in reducing the fracture gap as well as placing the cephalic screw into the optimal position. The forward-striking technique was particularly effective in reducing atypical SFFs with a transverse or short oblique configuration.

Comparison of dynamic versus static fixation of intramedullary nailing in tibial diaphyseal fractures: A systematic review and meta-analysis

INTRODUCTION

Tibial fractures are common long bone injuries, often surgically fixed with intramedullary nails. Modern intramedullary tibial nails allow for two different fixation modes, namely static and dynamic modes. While studies have demonstrated benefits of using either fixation modes, there has been no consensus as to which fixation mode would produce better outcomes and less complications. This systematic review and meta-analysis aims to compare the efficacy and safety of dynamic versus static fixation of intramedullary nails in the operative fixation of tibial diaphyseal fractures.

METHODS

A meta-analysis was conducted with a multi-database search (PubMed, OVID, EMBASE, Medline) according to PRISMA guidelines on April 15, 2021. Data from all published literature meeting inclusion criteria were extracted and analysed with fixed- and random-effects models.Findings/results: A total of 478 statically fixed and 234 dynamically fixed patients were included in this meta-analysis. Dynamically fixed patients had a significantly shorter mean time to union (mean difference, MD = 5.18 weeks, 95%CI: 1.95-8.41 weeks, p = 0.002) and reoperation rates (OR = 0.21, 95%CI: 0.10-0.47, p < 0.001) than statically fixed patients. No significant difference was found between both groups in terms of malrotation (OR = 0.57, 95% CI: 0.07-4.41, p = 0.59), non-union (OR = 1.10, 95% CI: 0.24-5.05, p = 0.91), delayed union (OR = 1.15, 95%CI: 0.19-7.17, p = 0.88) and malunion (OR = 2.73, 95% CI: 0.29-25.26, p = 0.38).

CONCLUSION

While acknowledging that there is widespread surgeon preference to dyanamise or statically fix intramedullary nails in certain tibial fracture configurations, primary dynamic fixation of intramedullary tibial nails demonstrated significantly shorter times to bony union and less complications than static nailing in our meta-analysis. Further research on identifying patient factors and fracture patterns that would best benefit from dynamic fixation is required.

A coupled computational framework for bone fracture healing and long-term remodelling: Investigating the role of internal fixation on bone fractures

In this study, a coupled computational modelling framework for bone fracture repair is presented that enables predictions of both healing and remodelling phases of the fracture region and is used to investigate the role of an internal fixation plate on the long-term healing performance of a fracture tibia under a range of different conditions. It was found that introduction of a titanium plate allowed the tibia to undergo successful healing at higher loading conditions and fracture gaps, compared with the non-plated versions. While these plated cases showed faster rates of repair in the healing phase, their performance was substantially different once they entered the remodelling phase, with substantial regions of stress shielding predicted. This framework is one of the few implementations of both fracture healing and remodelling phases of bone repair and includes several innovative approaches to smoothing, time-averaging and time incrementation in its implementation, thereby avoiding any unwanted abrupt changes between tissue phenotypes. This provides a better representation of tissue development in the fracture site when compared with fracture healing models alone and provides a suitable platform to investigate the long-term performance of orthopaedic fixation devices. This would enable the more effective design of permanent fixation devices and optimisation of the spatial and temporal performance of bioabsorbable implants.

The Butterfly Fragment in Wedge-Shaped Femoral Shaft Fracture: Comparison of Two Different Surgical Methods

Objective

Our study compared the results of wedge‐shaped femoral shaft fracture following intramedullary (IM) nailing with or without fixation of the third fragment.

Methods

We retrospectively reviewed patients presenting with femoral shaft fracture with AO/OTA type 32‐B from 2011 to 2016. Patients were divided into two groups: closed reduction without touching the third fragment and open reduction with fixation of the third fragment. The fragment ratio, fragment length, nail size, dynamization or not, mRUST scores, union rate, and union time were compared between the two groups. Risk factors of non‐union were also investigated, including sex, age, fracture pattern, fracture location, dynamization, nail size, fragment ratio, fragment size, and postoperative fragment displacement.

Results

A total of 80 patients met inclusion criteria, 20 patients with wedge‐shaped shaft femoral fracture were managed with IM nailing and open reduction with fixation of the third fragment. Sixty patients were treated with IM nail without touching the third fragment. The union rate for the fixation and non‐fixation groups were 60.0% and 81.7%, respectively. The mean union time for the fixation group was 19 months vs 14 months for the non‐fixation group. Multi‐regression analysis showed larger nail size (odds ratio: 2.26) and fixation of the third fragment (odds ratio: 0.18) influenced fracture healing.

Conclusions

Fixation of the third fragment in wedge‐shaped shaft femoral fracture results in a longer union time and lower union rate. In the management of femoral fracture with a third fragment, a larger nail size is recommended and fixation should be performed in a closed manner. Fixation of the fragment may achieve better fracture reduction. However, disruption of the vasculature and surrounding structures may further result in nonunion of the fracture site.

Closed-wedge high tibial osteotomy is more advantageous to maintain the correction than open-wedge high tibial osteotomy in osteopenic patients

PURPOSE

To compare the incidence of correction loss and survival rate between closed-wedge and open-wedge high tibial osteotomies (CWHTO and OWHTO, respectively) in patients with osteopenic and normal bone.

METHODS

Retrospective review was conducted for 115 CWHTOs and 119 OWHTOs performed in osteopenic patients [- 2.5 < Bone mineral density (BMD) T scores ≤ - 1] and 136 CWHTOs and 138 OWHTOs performed in normal patients (BMD T score > - 1) from 2012 to 2019. Demographics were not different between CW- and OWHTOs in osteopenic and normal patients (n.s., respectively). Radiographically, the mechanical axis (MA), medial proximal tibial angle (MPTA), and posterior tibial slope (PTS) were evaluated pre- and postoperatively (2 weeks after HTO). The occurrence of hinge fractures was investigated using radiographs taken on the operation day. The correction change was calculated as the last follow-up value minus postoperative MPTA. Correction loss was defined when the correction change was ≥ 3°. The survival rate (failure: correction loss) was investigated.

RESULTS

There were no significant differences in the pre and postoperative MA, MPTA, PTS, and value changes between CW- and OWHTOs in osteopenic and normal patients (n.s., respectively); the incidence of unstable hinge fractures also did not differ significantly (CWHTO vs. OWHTO = 7 vs. 7.6% in osteopenic patients; 2.9 vs. 3.6% in normal patients; n.s., respectively). The average correction change (CWHTO = - 0.6°, OWHTO = - 1.3°, p = 0.007), incidence of correction loss (CWHTO = 1.7%, OWHTO = 9.2%, p = 0.019), and 5-year survival rates (CWHTO = 98.3%, OWHTO = 90.8%, p = 0.013) differed significantly in osteopenic patients; there were no significant differences in these results in normal patients (n.s., respectively).

CONCLUSION

CWHTO was more advantageous than OWHTO regarding the correction loss in osteopenic patients. Intra- and postoperative care that consider poor bone quality will be required when performing OWHTOs in osteopenic patients.

LEVEL OF EVIDENCE

III.

Determining the Tightrope Tightening Force for Effective Fixation of the Tibiofibular Syndesmosis during Osteomeatal Synthesis of Fibula Injuries

The issue of choosing the method for optimal surgical treatment of a broken fibula has been debatable for many years. At the same time, concomitant repair of tibiofibular syndesmosis injuries does not have a unified approach. It has been determined that osteosynthesis of broken shin bones with syndesmosis injury should combine stable fixation of the broken bone and should not limit the elastic properties of the syndesmosis. In case of a broken fibula, it is recommended to use a stable extracortical fixator and an elastic connection of the syndesmosis injury using a tightrope. An analytical model of the broken fibula, which is blocked with an extracortical fixator metal plate and elastically fixed with a tightrope, has been developed. The research object is the stress–strain state of the “broken fibula–extracortical titanium plate” composition under the action of tightrope tightening fixation. The main research result is an analytical dependence, which makes it possible to determine the permissible value of the tightrope tightening force for elastic fixation of the tibiofibular syndesmosis. The research results have been tested numerically, and the influence of the parameters of plate, bone and damage localization on the permissible value of the tightrope tightening force has been analyzed. By using the rational tightrope tightening force with stable–elastic fixation of the broken shin, it is possible to reduce the time before the start of loading on the injured extremity and accelerate the functional recovery of the patient.

Influence of therapeutic grip exercises induced loading rates in distal radius fracture healing with volar locking plate fixation

BACKGROUND AND OBJECTIVE

Therapeutic exercises could potentially enhance the healing of distal radius fractures (DRFs) treated with volar locking plate (VLP). However, the healing outcomes are highly dependant on the patient-specific fracture geometries (e.g., gap size) and the loading conditions at the fracture site (e.g., loading frequency) resulted from different types of therapeutic exercises. The purpose of this study is to investigate the effects of different loading frequencies induced by therapeutic exercises on the biomechanical microenvironment of the fracture site and the transport of cells and growth factors within the fracture callus, ultimately the healing outcomes. This is achieved through numerical modelling and mechanical testing.

METHODS

Five radius sawbones specimens (Pacific Research Laboratories, Vashon, USA) fixed with VLP (VRP2.0+, Austofix) were mechanically tested using dynamic test instrument (INSTRON E3000, Norwood, MA). The loading protocol used in mechanical testing involved a series of cyclic axial compression tests representing hand and finger therapeutic exercises. The relationship between the dynamic loading rate (i.e., loading frequency) and dynamic stiffness of the construct was established and used as inputs to a developed numerical model for studying the dynamic loading induced cells and growth factors in fracture site and biomechanical stimuli required for healing.

RESULTS

There is a strong positive linear relationship between the loading rate and axial stiffness of the construct fixed with VLP. The loading rates induced by the moderate frequencies (i.e., 1-2 Hz) could promote endochondral ossification, whereas relatively high loading frequencies (i.e., over 3 Hz) may hinder the healing outcomes or lead to non-union. In addition, a dynamic loading frequency of 2 Hz in combination of a fracture gap size of 3 mm could produce a better healing outcome by enhancing the transport of cells and growth factors at the fracture site in comparison to free diffusion (i.e. without loading), and thereby produces a biomechanical microenvironment which is favourable for healing.

CONCLUSION

The experimentally validated numerical model presented in this study could potentially contribute to the design of effective patient-specific therapeutic exercises for better healing outcomes. Importantly, the model results demonstrate that therapeutic grip exercises induced dynamic loading could produce a better biomechanical microenvironment for healing without compromising the mechanical stability of the overall volar locking plate fixation construct.

Lag screws for reduction of bilateral lateral mass fractures due to spinal trauma

Introduction

Bilateral fracture of the C1 lateral mass is a relatively uncommon type of traumatic lesion. Treatment of this kind of fractures is usually conservative, with either external immobilization or traction.

Research question

Whether surgical management, with placement of lag screws in lateral mass of C1, could represent a first-line treatment.

Material and methods

We describe a case of 67-years old man with bilateral fractures of lateral mass of Atlas due to road accident trauma without ligament lesion but severe gap between bone edges. We performed Computed Tomography and Magnetic Resonance scans for pre-operative imaging, X-Ray and CT scan for follow-up. Medtronic navigation system was used as intraoperative guidance for screw placement.

Results

Radiological and clinical results were good, with optimal bone reduction and patient's early return to daily activities.

Discussion and conclusion

Surgical management remains debateable for isolated C1 lateral mass fractures. Different surgical approaches have been described for atlas fractures, such as transoral anterior C1-ring plate osteosynthesis, posterior osteosynthesis with a lateral mass screw rod, and posterior C1 to C2 fusion and C0 to C2 fusion. Minimally invasive operative treatment with lag screw and reduction of fracture's edges without occiput-C1 or C1-C2 stabilization could be the optimal treatment with good result and decreasing rate of pseudoarthrosis, allowing to avoid Halo-vest discomfort and complications.

•

Bilateral fracture of the C1 lateral mass is relatively uncommon type of traumatic lesion.

•

When gap among fracture's edges is severe there is high rate of not fusion or pseudoarthrosis.

•

Surgical reduction with bilateral lag screw, preserving C1-C2 motion and good results at follow-up imaging.

Retrograde tibial nailing of far distal tibia fractures: a biomechanical evaluation of double- versus triple-distal interlocking

Objectives

Retrograde tibial nailing using the Distal Tibia Nail (DTN) is a novel surgical option in the treatment of distal tibial fracture. Its unique retrograde insertion increases the range of surgical options in far distal fractures of the tibia beyond the use of plating. The aim of this study was to assess the feasibility of the DTN for far distal tibia fractures where only double rather than triple-distal locking is possible due to fracture localisation and morphology.

Methods

Six Sawbones^® were instrumented with a DTN and an AO/OTA 43-A3 fracture simulated. Samples were tested in two configurations: first with distal triple locking, second with double locking by removing one distal screw. Samples were subjected to compressive (350 N, 600 N) and torsional (± 8 Nm) loads. Stiffness construct and interfragmentary movement were quantified and compared between double and triple-locking configurations.

Results

The removal of one distal screw resulted in a 60–70% preservation of compressive stiffness, and 90% preservation of torsional stiffness for double locking compared to triple locking. Interfragmentary movement remained minimal for both compressive and torsional loading.

Conclusions

The DTN with a distal double locking can, therefore, be considered for far distal tibia fractures where nailing would be preferred over plating.

Development and validation of a modularized external fixator for generating standardized fracture healing micromotions in rats

Aims

To fully verify the reliability and reproducibility of an experimental method in generating standardized micromotion for the rat femur fracture model.

Methods

A modularized experimental device has been developed that allows rat models to be used instead of large animal models, with the aim of reducing systematic errors and time and money constraints on grouping. The bench test was used to determine the difference between the measured and set values of the micromotion produced by this device under different simulated loading weights. The displacement of the fixator under different loading conditions was measured by compression tests, which was used to simulate the unexpected micromotion caused by the rat’s ambulation. In vivo preliminary experiments with a small sample size were used to test the feasibility and effectiveness of the whole experimental scheme and surgical scheme.

Results

The bench test showed that a weight loading < 500 g did not affect the operation of experimental device. The compression test demonstrated that the stiffness of the device was sufficient to keep the uncontrollable motion between fracture ends, resulting from the rat’s daily activities, within 1% strain. In vivo results on 15 rats prove that the device works reliably, without overburdening the experimental animals, and provides standardized micromotion reproductively at the fracture site according to the set parameters.

Conclusion

Our device was able to investigate the effect of micromotion parameters on fracture healing by generating standardized micromotion to small animal models.

Cite this article: Bone Joint Res 2021;10(11):714–722.

An examination of two different approaches for the study of femoral neck fracture: Towards a more relevant rodent model

Femoral neck fractures are a massive personal and health programme burden. Methods to study femoral neck strength, across its combined trabecular and cortical components are therefore essential. Rodent ovariectomy-induced osteoporosis models are commonly coupled with ex vivo 3-/4-point bending methods to measure changes in femoral cortical diaphysis. The loading direction used to assess these properties are often non-physiologic and, moreover, these ovariectomy models are linked to marked weight gain that can influence the biomechanical properties. Herein, we explore whether more physiological axial ex vivo loading protocols applied to femoral neck samples of ovariectomised (OVX) rodents provide anatomically-relevant models for the assessment of strength. We examine the use of mouse and rat femurs, loaded in constrained and unconstrained configuration, respectively, and explore whether weight-correction increases their utility. Accordingly, the mid-shaft of the proximal half of femurs from OVX and sham-operated (Sham) mice was methacrylate-anchored and the head loaded parallel to the diaphysis (constrained). Alternatively, femurs from OVX and Sham rats were isolated intact and axially-loaded through hip and knee joint articular surfaces (unconstrained). Yield displacement, stiffness, maximum load and resilience were measured and fracture pattern classified; effects of body weight-correction via a linear regression method or simple division were assessed. Our data reveal significant deficiencies in biomechanical properties in OVX mouse femurs loaded in constrained configuration, only after weight-correction by linear regression. In addition, evaluation of rat femur biomechanics in unconstrained loading demonstrated greater variation and that weight-correction by simple division improved scope to reveal significant OVX impact. We conclude that greater femoral neck fracture susceptibility can indeed be measured in OVX rodents as long as multiple biomechanical parameters are reported, care is taken in choosing the method for assessing load-bearing strength and weight-correction applied. These studies advance the establishment of more relevant rodent models for the study of femoral neck fracture.

The role of intermittent PTH administration in conjunction with allogenic stem cell treatment to stimulate fracture healing

Aims

A growing number of fractures progress to delayed or nonunion, causing significant morbidity and socioeconomic impact. Localized delivery of stem cells and subcutaneous parathyroid hormone (PTH) has been shown individually to accelerate bony regeneration. This study aimed to combine the therapies with the aim of upregulating fracture healing.

Methods

A 1.5 mm femoral osteotomy (delayed union model) was created in 48 female juvenile Wistar rats, aged six to nine months, and stabilized using an external fixator. At day 0, animals were treated with intrafracture injections of 1 × 10⁶ cells/kg bone marrow mesenchymal stem cells (MSCs) suspended in fibrin, daily subcutaneous injections of high (100 μg/kg) or low (25 μg/kg) dose PTH 1-34, or a combination of PTH and MSCs. A group with an empty gap served as a control. Five weeks post-surgery, the femur was excised for radiological, histomorphometric, micro-CT, and mechanical analysis.

Results

Combination therapy treatment led to increased callus formation compared to controls. In the high-dose combination group there was significantly greater mineralized tissue volume and trabecular parameters compared to controls (p = 0.039). This translated to significantly improved stiffness (and ultimate load to failure (p = 0.049). The high-dose combination therapy group had the most significant improvement in mean modified Radiographic Union Score for Tibia fractures (RUST) compared to controls (13.8 (SD 1.3) vs 5.8 (SD 0.5)). All groups demonstrated significant increases in the radiological scores – RUST and Allen score – histologically compared to controls.

Conclusion

We demonstrate the beneficial effect of localized MSC injections on fracture healing combined with low- or high-dose teriparatide, with efficacy dependent on PTH dose.

Cite this article: Bone Joint Res 2021;10(10):659–667.

A comparative biomechanical study of the Distal Tibia Nail against compression plating for the osteosynthesis of supramalleolar corrective osteotomies

The Distal Tibia Nail (DTN; Mizuho, Japan) has demonstrated higher biomechanical stiffness to locking plates in previous research for A3 distal tibia fractures. It is here investigated as a fixation option for supramalleolar corrective osteotomies (SMOT). Sixteen Sawbones tibiae were implanted with either a DTN (n = 8) or Medial Distal Tibia Plate (MDTP; n = 8) and a SMOT simulated. Two surgical outcome scenarios were envisaged: "best-case" representing an intact lateral cortex, and "worst-case" representing a fractured lateral cortex. All samples were subjected to compressive (350 N, 700 N) and torsional (± 4 Nm, ± 8 Nm) testing. Samples were evaluated using calculated construct stiffness from force-displacement data, interfragmentary movement and Von Mises' strain distribution. The DTN demonstrated a greater compressive stiffness for the best-case surgical scenario, whereas the MDTP showed higher stiffness (p < 0.05) for the worst-case surgical scenario. In torsional testing, the DTN proved more resistant to torsion in the worst-case surgical setup (p < 0.05) for both ± 4 Nm and ± 8 Nm. The equivalent stiffness of the DTN against the MDTP supports the use of this implant for SMOT fixation and should be considered as a treatment option particularly in patients presenting vascularisation problems where the MDTP is an inappropriate choice.

Preliminary results in anterior cervical discectomy and fusion with the uncovertebral joint fusion cage in a goat model

Objective

To preliminarily evaluate the safety and efficacy of the uncovertebral joint fusion cage in a goat model of cervical spine interbody fusion.

Methods

Twenty-four healthy adult goats were randomly assigned to one of the two following groups: Group A, goats were implanted with an uncovertebral joint fusion cage combined with a local autograft and Group B, goats were implanted with a non-profile cage filled with a local autograft. The goats were prospectively evaluated for 24 weeks and then were sacrificed for evaluation. X-rays, CT and micro-CT scanning, and undecalcified bone histological analysis were used for the evaluation of fusion.

Results

75.0% (9/12) of the goats in Group A were evaluated as having fusion at 12 weeks, compared to 41.7% (5/12) in Group B. 83.3% (10/12) of the goats in Group A were evaluated as having fusion at 24 weeks compared to 58.3% (7/12) in Group B. The fusion grading scores in Group A were significantly higher than that in Group B both at 12 weeks and 24 weeks (P < 0.05). Micro-CT scanning and undecalcified bone histological analysis showed that new bone formation can be obviously found in the bilateral uncovertebral joint. The bone volume fraction (BV/ TV) in Group A (23.59 ± 4.43%) was significantly higher than Group B (16.16 ± 4.21%), with P < 0.05.

Conclusions

Preliminary results of this study demonstrated that uncovertebral joint fusion cage is effective for achieving early bone formation and fusion without increase of serious complications.

Influence of parameter deviation on the closeness of the tibial limb and external fixator based on a novel collision detection algorithm

The Ortho-SUV frame (OSF) is a hexapod external fixator widely applied in orthopedics deformity correction. The possibility of collision between OSF's struts and the soft tissue is an essential but overlooked issue. To avoid the issue, a novel collision detection algorithm is established based on a cone-cylinder model of the tibial limb-strut interaction for detecting the closeness of the tibial limb and external fixator. The algorithm is constructed using the vector analysis based on the model of the minimum distance between the truncated cone generatrix and the cylinder axis. The motion simulation is performed on the overall alignment through the Solidworks-motion module to verify the feasibility of the algorithm. Subsequently, the installation parameter deviations of the bone-fixator system are described to investigate the influence of orientation and position deviation on the closeness of the tibial limb and external fixator through the numerical method. The investigation results show that the orientation deviation γ (around the z-axis), the position deviation τ₁ and τ₂ (along the x and y-axes, respectively) have greater sensitivity to closeness and the influence of multiple deviations on the closeness has the property of superposition. The proposed algorithm can assist clinicians to strictly design and appraise frame configurations prior to their application to avoid the collision between the external fixator and the limbs during the correction. It has great application significance in the development of computer-aided correction software.

Balance Between Mechanical Stability and Mechano-Biology of Fracture Healing Under Volar Locking Plate

The application of volar locking plate (VLP) is promising in the treatment of dorsally comminuted and displaced fracture. However, the optimal balance between the mechanical stability of VLP and the mechanobiology at the fracture site is still unclear. The purpose of this study is to develop numerical models in conjunction with experimental studies to identify the favourable mechanical microenvironment for indirect healing, by optimizing VLP configuration and post-operative loadings for different fracture geometries. The simulation results show that the mechanical behaviour of VLP is mainly governed by the axial compression. In addition, the model shows that, under relatively large gap size (i.e., 3-5 mm), the increase of FWL could enhance chondrocyte differentiation while a large BPD could compromise the mechanical stability of VLP. Importantly, bending moment produced by wrist flexion/extension and torsion moment produced from forearm rotation could potentially hinder endochondral ossification at early stage of healing. The developed model could potentially assist orthopaedic surgeons in surgical pre-planning and designing post-operation physical therapy for treatment of distal radius fractures.

Outcomes of conservative treatment for bony mallet fingers

BACKGROUND

The treatment strategy for bony mallet fingers remains controversial. The outcomes of conservative treatment were investigated in this study. In addition, the time to bone union, and gap between the bone fragment and distal phalanx are discussed.

METHODS

The subjects were 26 patients (27 fingers) with bony mallet fingers (20 males and 6 females, mean age: 46.0 years old, the mean limitation of extension of the distal interphalangeal (DIP) joint: - 20.2°). In conservative treatment, splinting was applied for 6 weeks, followed by 2-week taping. The time to bone union, range of motion of the DIP joint, and the Crawford classification on the final follow-up were investigated. In addition, the bone fragment occupation rate was evaluated on plain radiography on the first examination. Furthermore, the gap on the first examination and after splinting. The relationship between the gap and bone union period was also investigated.

RESULTS

The mean time from injury to bone union was 170.2 days, the mean range of motion of the DIP joint was - 8.5° in extension and 60.9° in flexion, and the Crawford classification was Excellent for 22 fingers, Good for 2, Fair for 2, and Poor for 1. On the first examination, the mean bone fragment occupation rate was 44.0%. The mean gap on the first examination was 1.1 mm and this was significantly narrowed to 0.8 mm after splinting (p < 0.01). No significant correlation was noted between the time to bone union and gap on the first examination (p = 0.16), however, a significant positive correlation was noted between them after splinting (p < 0.01).

CONCLUSIONS

This study suggested that a favorable clinical outcome can be achieved by conservative treatment. Moreover, the bone union period decreased as the gap after splinting decreased, being significantly correlated.

Full-field strain of regenerated bone tissue in a femoral fracture model

The mechanical behaviour of regenerated bone tissue during fracture healing is key in determining its ability to withstand physiological loads. However, the strain distribution in the newly formed tissue and how this influences the way a fracture heals it is still unclear. X-ray Computed Tomography (XCT) has been extensively used to assess the progress of mineralised tissues in regeneration and when combined with in situ mechanics and digital volume correlation (DVC) has been proven a powerful tool to understand the mechanical behaviour and full-field three-dimensional (3D) strain distribution in bone. The purpose of this study is therefore to use in situ XCT mechanics and DVC to investigate the strain distribution and load-bearing capacity in a regenerating fracture in the diaphyseal bone, using a rodent femoral fracture model stabilised by external fixation. Rat femurs with 1 mm and 2 mm osteotomy gaps were tested under in situ XCT step-wise compression in the apparent elastic region. High strain was present in the newly formed bone (ε_p1 and ε_p3 reaching 29 000 µε and -43 000 µε, respectively), with a wide variation and inhomogeneity of the 3D strain distribution in the regenerating tissues of the fracture gap, which is directly related to the presence of unmineralised tissue observed in histological images. The outcomes of this study will contribute in understanding natural regenerative ability of bone and its mechanical behaviour under loading.