Effect of medial-lateral malpositioning of the femoral component in total knee arthroplasty on anterior knee pain at greater than 8 years of follow-up

Is Mediolateral Translation of Femur Caused by Total Knee Arthroplasty Being Ignored?

Purpose

This study aims to show the change in overall congruency due to mediolateral translation after total knee arthroplasty compared with normal knee anatomy.

Methods

This study was performed in two parts. In part 1, the relationship between femur and tibia was defined by new parameters on the antero-posterior radiographs of 84 patients. In part 2, this relationship was evaluated on the postoperative radiographs of 136 total knee arthroplasty patients. Two parallel lines to the tibial anatomical axis were drawn tangent to the most lateral and most medial parts of the tibial plateau. After creating medial and lateral tangential lines, the distance between the most lateral point of the lateral femoral epicondyle and lateral tangential line and the most medial point of the medial femoral epicondyle and medial tangential line was measured. Another new parameter described in the study is epicondylar distance ratio. The ratios between the shortest distance between tibial anatomical axis and lateral femoral epicondyle and the distance between tibial anatomical axis and medial femoral epicondyle were defined.

Results

It was found that the lateral tangent was not superposed in any measurement to the femoral lateral condyle, the closest tangent was passed, and the mean lateral space distance was 1.8 mm (SD 1.5, 95% CI 0-5.3 mm). The medial tangent was passed from the lateral to the femoral medial epicondyle, and the medial crossing distance was 8.5 mm (SD 5.7, 95% CI 5-14 mm). Epicondylar distance ratio used as the second measurement was 0.8 (0.5-0.9). After total knee arthroplasty measurements showed that the line passing through the lateral tibia crossed the lateral epicondyle of the femur and intersected at an average distance of 4.3 mm (SD 4.1, 95% CI 1-11.2 mm).

Conclusions

There is a coronal plane congruence between tibia and femur in the healthy knees, which get changed after total knee arthroplasty.

Preoperative patellar bone marrow lesions with full thickness cartilage defects correlate with residual anterior knee pain in total knee arthroplasty without patellar resurfacing

PURPOSE

Residual anterior knee pain is one of the most common problems after total knee arthroplasty (TKA). However, the contributing factors affecting postoperative anterior knee pain (AKP) remain poorly understood. This study aimed to evaluate the effect of preoperative patellar bone marrow lesions (BMLs) and patellar cartilage defects on postoperative AKP after patellar non-resurfacing TKA.

METHODS

This retrospective study included 336 patients who underwent unilateral TKA without patella resurfacing. All patients underwent preoperative magnetic resonance imaging (MRI) to assess the presence of BMLs and the degree of cartilage defects in the patella. Patients were categorized into four groups according to the presence of BMLs (with or without BMLs) and the degree of cartilage defects (with or without full thickness cartilage defects). The Kujala Anterior Knee Pain Scale (AKPS) and the Hospital for Special Surgery Knee Rating Scale (HSS) scores at 2 years after TKA were compared among the groups.

RESULTS

Preoperative BMLs in the patella were found in 132 (39.3%) of 336 cases. Among the four groups, the group with both BMLs and full-thickness cartilage defects demonstrated significantly lower AKPS compared to the other groups at 2 years after TKA (p < 0.01), but no significant difference was shown in the HSS scores, between these groups. There were no significant differences in either AKPS or HSS scores among the other three patient groups.

CONCLUSIONS

The presence of preoperative BMLs with full-thickness cartilage defects in the patella was associated with worse postoperative AKP after TKA without patella resurfacing. Patella resurfacing should be considered in this patient group to minimize the risk of developing residual AKP after TKA.

LEVEL OF EVIDENCE

III.

Learning curve of robot-assisted total knee arthroplasty and its effects on implant position in asian patients: a prospective study

BACKGROUND

Robot-assisted total knee arthroplasty (r-TKA) can reportedly achieve more accurate implant positioning than conventional total knee arthroplasty (c-TKA), although its learning curve is controversial. Moreover, few studies have investigated r-TKA in Asians, who have different anatomical characteristics. This study aimed to determine the learning curve for r-TKA and compare implant positions between r-TKA and c-TKA according to the learning curve in Asian patients.

METHODS

This prospective study included 50 consecutive c-TKAs (group C), followed by 50 consecutive r-TKAs conducted using the MAKO robotic system (Stryker, USA). Cumulative summation analyses were performed to assess the learning curve for operative time in r-TKA. Accordingly, the r-TKA cases were divided into the initial (group I) and proficiency cases (group P). The femoral and tibial component positions in the coronal, sagittal, and axial planes and lower limb alignment were compared among the three groups.

RESULTS

r-TKA was associated with a learning curve for operative time in 18 cases. The operative time was significantly shorter in groups C and P than that in group I, with no significant difference between groups C and P. Groups I and P demonstrated fewer outliers with respect to lower limb alignment, femoral component coronal position, axial position, and tibial component sagittal position than those in group C, with no significant difference between groups I and P.

CONCLUSION

The operative time did not differ significantly between r-TKA and c-TKA after the learning curve. Surgeons could expect more accurate and reproducible lower limb alignment and implant positioning with r-TKA in Asian patients, irrespective of the learning curve.

Computer-based analysis of different component positions and insert thicknesses on tibio-femoral and patello-femoral joint dynamics after cruciate-retaining total knee replacement

BACKGROUND

Positioning of the implant components and tibial insert thickness constitute critical aspects of total knee replacement (TKR) that influence the postoperative knee joint dynamics. This study aimed to investigate the impact of implant component positioning (anterior-posterior and medio-lateral shift) and varying tibial insert thickness on the tibio-femoral (TF) and patello-femoral (PF) joint kinematics and contact forces after cruciate-retaining (CR)-TKR.

METHOD

A validated musculoskeletal multibody simulation (MMBS) model with a fixed-bearing CR-TKR during a squat motion up to 90° knee flexion was deployed to calculate PF and TF joint dynamics for varied implant component positions and tibial insert thicknesses. Evaluation was performed consecutively by comparing the respective knee joint parameters (e.g. contact force, quadriceps muscle force, joint kinematics) to a reference implant position.

RESULTS

The PF contact forces were mostly affected by the anterior-posterior as well as medio-lateral positioning of the femoral component (by 3 mm anterior up to 31 % and by 6 mm lateral up to 14 %). TF contact forces were considerably altered by tibial insert thickness (24 % in case of + 4 mm increase) and by the anterior-posterior position of the femoral component (by 3 mm posterior up to 16 %). Concerning PF kinematics, a medialised femoral component by 6 mm increased the lateral patellar tilt by more than 5°.

CONCLUSIONS

Our results indicate that regarding PF kinematics and contact forces the positioning of the femoral component was more critical than the tibial component. The positioning of the femoral component in anterior-posterior direction on and PF contact force was evident. Orthopaedic surgeons should strictly monitor the anterior-posterior as well as the medio-lateral position of the femoral component and the insert thickness.

Lateral shift of the femoral condyle after total knee arthroplasty: simulation using 2D-templates of the medial pivot design on knee radiographs of young Japanese patients

Background

Total knee arthroplasty (TKA) is an established surgical treatment for advanced knee osteoarthritis by which patients can expect improvement of knee pain and function. Although many surgeons have investigated limb alignment after TKA, changes in coronal positional relation between the femur and tibia are not known well.

Methods

Radiographs of 105 knees of young Japanese patients between 20 and 49 years-old (60 men and 45 women) without osteoarthritic changes who received arthroscopic surgeries at our hospital were used in this study. Using 2D-templates of the medial pivot design (the FINE total knee), we simulated TKA on a SYNAPSE-PACS software. First, the femoral component was placed in normal knee alignment and then was merged to the medial concave of the insert where the tibial component was placed in neutral alignment. The length of the mediolateral shift of the femoral component was measured as an estimate of lateral shift of the femoral condyle, of which association with radiographic parameters including the femorotibial angle (FTA), lateral distal femoral angle (LDFA), and medial proximal tibial angle (MPTA) was analyzed. Subjects were classified into three groups according to the femoral component size that was chosen in simulation of TKA, and the lateral shift of the femoral condyle was compared between groups.

Results

The estimated mean lateral shift of the femoral condyle was 5.99 ± 1.98 mm and was greater in males than females (p < 0.05). Also, it was most highly correlated with the medial proximal tibial angle (MPTA) (r = − 0.553, p < 0.01). A group receiving larger component sizes significantly shifted more laterally compared with a group receiving smaller component sizes (p < 0.01).

Conclusions

These results suggest that the coronal positional relation between the femur and tibia is altered and subsequent ligament imbalance may occur after mechanically aligned TKA using the medial pivot design.

Cemented Patellar Implant Malposition: A Non-Issue for the Painful Total Knee Arthroplasty

BACKGROUND

Non-optimal patellofemoral relationships may influence treatment decisions during revision total knee arthroplasty (TKA). We performed this study to determine whether patellar implant malposition or patellar tilt is associated with inferior patient-reported outcome scores or patient satisfaction after primary TKA.

METHODS

We identified 396 TKA patients (439 knees) from an institutional registry who had undergone patellar resurfacing, with preoperative and 6-week postoperative radiographs available, and patient-reported outcome measures (PROMs) completed at least 1 year after surgery (mean 505 days). Preoperative patient demographic characteristics, patient-reported expectations, National Institutes of Health - Patient Reported Outcomes Measurements Instrument Systems global health, Knee Injury and Osteoarthritis Outcome Score for Joint Replacement, and University of California Los Angeles activity scores were compared between 60 TKAs performed with non-optimal patellofemoral relationships (36 patellar implant malposition, 24 patellar tilt) and 379 TKAs performed with optimal patellar implant placement.

RESULTS

There were no differences between the 2 cohorts regarding demographic features, preoperative radiographic disease severity, expectations, and PROMs; or postoperative tibiofemoral component alignment, PROMs, and patient-reported satisfaction (P = .48). Knee Injury and Osteoarthritis Outcome Score for Joint Replacement improved similarly (P = .62) for patients with optimal resurfacing (48.5-77.6 points) and non-optimal resurfacing (47.7-76.6 points). A similar proportion of optimal and suboptimal resurfaced patients reported being satisfied with their TKA (92.7% vs 88.1%, P = .29).

CONCLUSION

Although suboptimal patellofemoral relationships may prompt treatment considerations during revision TKA, the data obtained from this study do not suggest that patellar implant malposition or patellar tilt independently contribute to postoperative pain, functional limitation, or dissatisfaction.

LEVEL OF EVIDENCE

This is a level III, retrospective cohort study.

Musculoskeletal Multibody Simulation Analysis on the Impact of Patellar Component Design and Positioning on Joint Dynamics after Unconstrained Total Knee Arthroplasty

Patellofemoral (PF) disorders are considered a major clinical complication after total knee replacement (TKR). Malpositioning and design of the patellar component impacts knee joint dynamics, implant fixation and wear propagation. However, only a limited number of studies have addressed the biomechanical impact of the patellar component on PF dynamics and their results have been discussed controversially. To address these issues, we implemented a musculoskeletal multibody simulation (MMBS) study for the systematical analysis of the patellar component’s thickness and positioning on PF contact forces and kinematics during dynamic squat motion with virtually implanted unconstrained cruciate-retaining (CR)-TKR. The patellar button thickness clearly increased the contact forces in the PF joint (up to 27%). Similarly, the PF contact forces were affected by superior–inferior positioning (up to 16%) and mediolateral positioning (up to 8%) of the patellar button. PF kinematics was mostly affected by the mediolateral positioning and the thickness of the patellar component. A medialization of 3 mm caused a lateral patellar shift by up to 2.7 mm and lateral patellar tilt by up to 1.6°. However, deviations in the rotational positioning of the patellar button had minor effects on PF dynamics. Aiming at an optimal intraoperative patellar component alignment, the orthopedic surgeon should pay close attention to the patellar component thickness in combination with its mediolateral and superior–inferior positioning on the retropatellar surface. Our generated MMBS model provides systematic and reproducible insight into the effects of patellar component positioning and design on PF dynamics and has the potential to serve as a preoperative analysis tool.

Different targets of mechanical alignment do not improve knee outcomes after TKA

BACKGROUND

Accurate alignment is a basic principle of TKA surgery, but achieving alignment within this target may not translate into superior outcomes after surgery.

PURPOSE

To assess if neutral TKA mechanical alignment was associated with superior knee outcomes and to examine the effect of various aspects of pre-operative and post-operative alignment on knee function.

METHODS

Analysis of a database of 444 TKA patients between June 2009 and October 2016. Knee outcomes (WOMAC, AKSS and knee range of motion) were collected before surgery and during follow-up at a minimum of six months.

RESULTS

Analysis included 444 TKA patients (62% female, mean age 66 years, mean follow-up 23 months). Deformity varied from 21° varus (mean = 7.9, SD = 2.8) to 17° valgus deformity (mean = 7.7, SD = 2.8). Pre-operatively, 101 (23%) knees were in native neutral mechanical alignment, while 278 (63%) were in varus and 65 (15%) were in valgus. Post-operatively, a group of 365 (82%) TKA were found to be in neutral mechanical alignment and a group of 79 (18%) TKA were noted to be 'Outliers' (17 [4%] TKA > 3° varus and 62 [14%] TKA > 3° valgus alignment). Restoration of the target of alignment of 0 ± 3° or 0 ± 1°, did not have better functional outcomes scores, range of motion or prosthesis longevity than those in the outlier range.

CONCLUSION

Neutral TKA alignment did not appear to be a significant contributing factor to the improvement in knee function in short-medium term follow-up.

Joint replacement in X-linked hypophosphatemia

X-linked hypophosphatemia (XLH) is associated with a pervasive, severe degenerative osteoarthritis. We conducted a retrospective chart review/patient survey using the Knee or Hip Osteoarthritis Outcome Score Physical Function Short Form. Fourteen total knee arthroplasties and 7 total hip arthroplasties among 11 patients were included. The mean KOOS-PS score was 31.4 ± 9.7 with a mean follow up of 6.9 years. Mean HOOS-PS score was 14.8 ± 12.9 at a mean follow up of 7.6 years. One knee failed due to aseptic loosening and one hip was revised due to polyethylene wear. In conclusion, total joint arthroplasty is beneficial in XLH.

Patellar tracking in primary total knee arthroplasty

This is a review of the recent literature of the various factors that affect patellar tracking following total knee arthroplasty (TKA).

Patellar tracking principally depends on the pre-existing patellar tracking and the rotational alignment of the femoral and tibial implants, but the detailed movements depend on the patellar shape. The latter means that the patellar kinematics of any implanted TKA does not return to normal.

Laboratory cadaveric studies use normal knees and non-activity-based testing conditions and so may not translate into clinical findings.

The recent literature has not added anything significant to change established clinical practice in achieving satisfactory patellar tracking following TKA.

Cite this article: EFORT Open Rev 2018;3:106-113. DOI: 10.1302/2058-5241.3.170036.

Mediolateral femoral component position in TKA significantly alters patella shift and femoral roll-back

PURPOSE

Increased retropatellar pressure and altered kinematics are associated with anterior knee pain and unsatisfied patients after total knee arthroplasty (TKA). Since malposition of the implant is believed to contribute to postoperative pain, we performed this in vitro study to evaluate the influence of mediolateral femoral component position on retropatellar pressure as well as tibio-femoral and patella kinematics.

METHODS

For the test, a fixed-bearing TKA was implanted in eight fresh frozen cadaver specimens. To determine the impact of mediolateral (ML) position, three variants of femoral components (3-mm medialization, neutral position and 3-mm lateralization) were produced using rapid prototyping replicas. In a knee rig, a loaded squat from 20° to 120° of flexion was applied. Retropatellar pressure distribution was measured with a pressure-sensitive film. Additionally, an ultrasonic-based three-dimensional motion analysis system was used to register patello- and tibio-femoral kinematics.

RESULTS

ML translation of the femoral component by 3 mm did not lead to a significant alteration in retropatellar peak pressure (medial 6.5 ± 2.5 MPa vs. lateral 6.0 ± 2.4 MPa). Following the ML translation of the femoral component, the patella was significantly shifted and tilted in the same directions. Varying the ML femoral component position also led to a significant alteration in femoral roll-back.

CONCLUSION

In day-by-day use, ML position should be chosen with care since there is a significant influence on patella shift and femoral roll-back. Retropatellar pressure is not significantly altered, so there is no clear evidence of an impact on anterior knee pain.

Superior-inferior position of patellar component affects patellofemoral kinematics and contact forces in computer simulation

BACKGROUND

Anterior knee pain has been reported as a major postoperative complication after total knee arthroplasty, which may lead to patient dissatisfaction. Rotational alignment and the medial-lateral position correlate with patellar maltracking, which can cause knee pain postoperatively. However, the superior-inferior position of the patellar component has not been investigated. The purpose of the current study was to investigate the effects of the patellar superior-inferior position on patellofemoral kinematics and kinetics.

METHODS

Superior, central, and inferior models with a dome patellar component were constructed. In the superior and inferior models, the position of the patellar component translated superiorly and inferiorly, respectively, by 3mm, relative to the center model. Kinematics of the patellar component, quadriceps force, and patellofemoral contact force were calculated using a computer simulation during a squatting activity in a weight-bearing deep knee bend.

FINDINGS

In the inferior model, the flexion angle, relative to the tibial component, was the greatest among all models. The inferior model showed an 18.0%, 36.5%, and 22.7% increase in the maximum quadriceps force, the maximum medial patellofemoral force, and the maximum lateral patellofemoral force, respectively, compared with the superior model.

INTERPRETATION

Superior-inferior positions affected patellofemoral kinematic and kinetics. Surgeons should avoid the inferior position of the patellar component, because the inferior positioned model showed greater quadriceps and patellofemoral force, resulting in a potential risk for anterior knee pain and component loosening.

Patella position is not a determinant for anterior knee pain 10 years after balanced gap total knee arthroplasty

PURPOSE

Incidence of anterior knee pain after total knee arthroplasty (TKA) is reported to be between 4 and 49 %. The incidence of AKP at long-term follow-up and possible determinants after cruciate cruciate-retaining TKA were investigated.

METHODS

A 10-year follow-up of a cohort of 55 patients (63 TKAs), who received the balanSys™ cruciate-retaining total knee system (Mathys Ltd, Bettlach, Switzerland) between 1999 and 2002, was performed. Patients had undergone the balanced gap technique, with either a fixed bearing or an AP-glide bearing. Standardised diagnostic questions regarding AKP were collected and categorised into two groups: those with and without AKP. The lateral patellar tilt, patellar displacement measurement and modified Insall-Salvati ratio were used for patella position evaluation on skyline radiographs. The Knee Society Score (KSS), the Knee Osteoarthritis Outcome Score (KOOS) and Numerical Rating Scales (NRS) for pain and satisfaction were obtained at follow-up.

RESULTS

Sixteen patients in the study population experienced AKP. Incidence of AKP (fixed bearing 13/44; AP-glide bearing baring 3/17) was not dependent on type of insert (n.s.). There were no statistical differences in patella position and tibiofemoral contact point between the AKP group and the no AKP group (n.s.). KSS, KOOS, NRS-pain and NRS-satisfaction were significantly lower for the patients with AKP (all p < 0.05).

CONCLUSION

Twenty-six percentage of the patients experienced AKP 10 years after balanced gap TKA. Postoperative patella positioning was not found to be a determinant for anterior knee pain after TKA. However, patellar displacement does not seem completely favourable. Moreover, type of bearing was not found a determinant for AKP at long-term follow-up.

LEVEL OF EVIDENCE

Lower quality prospective cohort study (<80 % follow-up, patients enrolled at different time points in disease), Level II.