Effect of systematic substitution of Na2O for SiO2 on devitrification and bioactivity of sol-gel derived 69.5SiO2-24.5CaO-6P2O5 ceramics

PVP as an Oxygen Vacancy-Inducing Agent in the Development of Black 45S5 Bioactive Glass Fibrous Scaffolds Doped with Zn and Mg Using A-HSBS

Currently, there is an increasing demand for advanced materials that can address the needs of tissue engineering and have the potential for use in treatments targeting tumor cells, such as black bioactive materials in photothermal therapy. Thus, 3D fibrous scaffolds of black 45S5 bioactive glass were produced using the air-heated solution blow spinning (A-HSBS) technique, with polyvinylpyrrolidone (PVP) serving as a spinning aid and an oxygen vacancy-inducing agent. Glass powder with the same composition was synthesized via the sol-gel route for comparison. The samples were characterized using thermogravimetric analysis, X-ray diffraction, FTIR spectroscopy, and scanning electron microscopy, along with in vitro tests using simulated body fluid (SBF), phosphate-buffered saline (PBS), and TRIS solution. The results showed that PVP enhanced oxygen vacancy formation and stabilized the scaffolds at 600 °C. Doping with Zn and Mg ions reduced crystallization while significantly increasing the fiber diameters. Scaffolds doped with Zn exhibited lower degradation rates, delayed apatite formation, and hindered ionic release. Conversely, Mg ions facilitated greater interaction with the medium and rapid apatite formation, completely covering the fibers. The scaffolds showed no cytotoxicity in the MTT assay at concentrations of up to 200 µg/mL for HaCat cells and 0.8 mg/mL for L929 cells. This study demonstrated the effectiveness of using PVP in the production of black bioactive glass scaffolds, highlighting their potential for bone regeneration.

Enhancement of induction heating capability of bioactive SiO2–CaO–Na2O–P2O5 glass-ceramics by selective substitution with magnetite nanoparticles

Magnetic bioactive glass-ceramics with compositions of 37SiO2–24.5CaO–24.5Na2O–6P2O5–8Fe3O4 (MGCS), 45SiO2–16.5CaO–24.5Na2O–6P2O5–8Fe3O4 (MGCC) and 45SiO2–24.5CaO–16.5Na2O–6P2O5–8Fe3O4 (MGCN) were synthesized by sol–gel route. These compositions were derived by substituting 8 wt.% magnetite (Fe3O4) nanoparticles for SiO2, CaO and Na2O, respectively, in the bioactive glass-ceramic of composition 45SiO2–24.5CaO–24.5Na2O–6P2O5. The sol–gel derived powders were heat treated at 550 °C for 1 h to ensure optimal amounts of magnetite, combeite and sodium nitrate phases. All the heat treated samples were found to be magnetic, bioactive and non-toxic to MG-63 osteoblast cells. However, the induction heating response of MGCC was better than that of MGCS and MGCN. Notably, MGCC outperformed the commercially available ferrofluid FluidMag-CT, thereby establishing itself as a superior thermoseed for magnetic hyperthermia treatment of cancer.

Impact of Iron Oxide Phases on the Magnetic Induction Heating Capacity of Mesoporous 45SiO2-16.5CaO-24.5Na2O-6P2O5-8Fe3O4 Glass-Ceramics

Sol-gel-based mesoporous 45SiO2-16.5CaO-24.5Na2O-6P2O5-8Fe3O4 bioglass-ceramics were obtained by substituting magnetite nanoparticles for CaO in a 45SiO2-24.5CaO-24.5Na2O-6P2O5 bioglass composition. To enhance the dissolution of the precursors and to vary the crystalline phases, the as-synthesized ceramic powders were processed for 1 h each at temperatures (TA) between 550 and 700 °C. A gradual decline in the saturation magnetization with an increase in TA was observed, which is linked to the gradual conversion of magnetite into hematite at different TA > 550 °C. All of the processed samples indicated a hydroxyapatite surface layer formation in in vitro tests. Aqueous solutions of the ceramic processed at 600 °C exhibited superior magnetic induction capacity. Thus, the substitution of magnetite nanoparticles for CaO in the base composition, coupled with appropriate heat treatment, results in a promising bioactive glass-ceramic for magnetic hyperthermia treatment of deep-rooted cancer cells.

Research on Sol-Gel Synthesis of Low-Temperature Na2O-B2O3-SiO2 Vitrified Bonds and Preparation of High-Strength Stacked Abrasives Using the Molding and Crushing Method

Currently, the sol-gel technique is employed in the synthesis of high-performance vitrified bonds; however, its application in the fabrication of stacked abrasives has been minimally explored. Furthermore, the methods utilized in the production of abrasive particles for stacked abrasives are technically challenging and incur high costs, which hinders their actual industrial application. Consequently, this study utilizes the sol-gel approach to synthesize a Na2O-B2O3-SiO2 ternary system vitrified bond powder and employs a molding and crushing method, which offers a lower technological barrier and reduced preparation costs, for the production of abrasive particles subsequently fabricating corundum stacked abrasives. Upon setting the binder composition to a molar ratio of n(SiO2):n(B2O3):n(Na2O) = 65:23:12, it was observed that the crystallization within the glass matrix was minimized and the optimal sintering temperature for the synthesized laminate abrasive to be sustained at 820 °C. At the aforementioned temperature, the binder melt is capable of flowing uniformly amongst the abrasive granules, thereby ensuring a robust encapsulation of the particles. The average single particle compressive strength of the prepared corundum stacked abrasive with a grain size of forty mesh can reach the highest of all composition points at 28.56 N and the average single particle compressive strength of the prepared diamond stacked abrasive is 28.14 N.