The role of coupled resistance-compliance in upper tracheobronchial airways under high frequency oscillatory ventilation

Endotracheal tube, by the venturi effect, reduces the efficacy of increasing inlet pressure in improving pendelluft

In mechanically ventilated severe acute respiratory distress syndrome patients, spontaneous inspiratory effort generates more negative pressure in the dorsal lung than in the ventral lung. The airflow caused by this pressure difference is called pendelluft, which is a possible mechanisms of patient self-inflicted lung injury. This study aimed to use computer simulation to understand how the endotracheal tube and insufficient ventilatory support contribute to pendelluft. We established two models. In the invasive model, an endotracheal tube was connected to the tracheobronchial tree with 34 outlets grouped into six locations: the right and left upper, lower, and middle lobes. In the non-invasive model, the upper airway, including the glottis, was connected to the tracheobronchial tree. To recreate the inspiratory effort of acute respiratory distress syndrome patients, the lower lobe pressure was set at -13 cmH2O, while the upper and middle lobe pressure was set at -6.4 cmH2O. The inlet pressure was set from 10 to 30 cmH2O to recreate ventilatory support. Using the finite volume method, the total flow rates through each model and toward each lobe were calculated. The invasive model had half the total flow rate of the non-invasive model (1.92 L/s versus 3.73 L/s under 10 cmH2O, respectively). More pendelluft (gas flow into the model from the outlets) was observed in the invasive model than in the non-invasive model. The inlet pressure increase from 10 to 30 cmH2O decreased pendelluft by 11% and 29% in the invasive and non-invasive models, respectively. In the invasive model, a faster jet flowed from the tip of the endotracheal tube toward the lower lobes, consequently entraining gas from the upper and middle lobes. Increasing ventilatory support intensifies the jet from the endotracheal tube, causing a venturi effect at the bifurcation in the tracheobronchial tree. Clinically acceptable ventilatory support cannot completely prevent pendelluft.

Fluid dynamic assessment of positive end-expiratory pressure in a tracheostomy tube connector during respiration

High-flow oxygen therapy using a tracheostomy tube is a promising clinical approach to reduce the work of breathing in tracheostomized patients. Positive end-expiratory pressure (PEEP) is usually applied during oxygen inflow to improve oxygenation by preventing end-expiratory lung collapse. However, much is still unknown about the geometrical effects of PEEP, especially regarding tracheostomy tube connectors (or adapters). Quantifying the degree of end-expiratory pressure (EEP) that takes patient-specific spirometry into account would be useful in this regard, but no such framework has been established yet. Thus, a platform to assess PEEP under respiration was developed, wherein three-dimensional simulation of airflow in a tracheostomy tube connector is coupled with a lumped lung model. The numerical model successfully reflected the magnitude of EEP measured experimentally using a lung phantom. Numerical simulations were further performed to quantify the effects of geometrical parameters on PEEP, such as inlet angles and rate of stenosis in the connector. Although sharp inlet angles increased the magnitude of EEP, they cannot be expected to achieve clinically reasonable PEEP. On the other hand, geometrical constriction in the connector can potentially result in PEEP as obtained with conventional nasal cannulae.

Independent Lung Ventilation-Experimental Studies on a 3D Printed Respiratory Tract Model

Independent lung ventilation (ILV) is a life-saving procedure in unilateral pulmonary pathologies. ILV is underused in clinical practice, mostly due to the technically demanding placement of a double lumen endotracheal tube (ETT). Moreover, the determination of ventilation parameters for each lung in vivo is limited. In recent years, the development of 3D printing techniques enabled the production of highly accurate physical models of anatomical structures used for in vitro research, considering the high risk of in vivo studies. The purpose of this study was to assess the influence of double-lumen ETT on the gas transport and mixing in the anatomically accurate 3D-printed model of the bronchial tree, with lung lobes of different compliances, using various ventilation modes. The bronchial tree was obtained from Respiratory Drug Delivery (RDD Online, Richmond, VA, USA), processed and printed by a dual extruder FFF 3D printer. The test system was also composed of left side double-lumen endotracheal tube, Siemens Test Lung 190 and anesthetic breathing bag (as lobes). Pressure and flow measurements were taken at the outlets of the secondary bronchus. The measured resistance increased six times in the presence of double-lumen ETT. Differences between the flow distribution to the less and more compliant lobe were more significant for the airways with double-lumen ETT. The ability to predict the actual flow distribution in model airways is necessary to conduct effective ILV in clinical conditions.

The effect of the volumetric flow rate and endotracheal tube diameter on the pressure distribution in human airways

The comprehension of the fluid flow in the upper airways is of paramount importance when treating patients under clinical conditions that demand mechanical ventilation. Barotrauma and overdistension are related to undesirable pressures and might be responsible for morbidity and mortality. In the current work we use computational fluid dynamics to investigate the pressure field in the upper respiratory airways. We performed a set of simulations varying the volumetric flow rate of mechanical ventilators and we have shown that the pressure profile can be calculated by means of the volumetric flow rate in accordance with a mathematical expression given by P_av=aV˙², where P_av is the average pressure at selected sections of the upper airways and V˙ is the volumetric flow rate. Numerical findings provide evidence that the constant a varies with the location of the plane in the upper airways. We also show that some particular diameters of endotracheal tubes (ETT) must be used with care for a given range of volumetric flow rates. Overall, we document an important relationship among pressure, volumetric flow rate and selected internal diameters from ETT.

A compartment-quasi-3D multiscale approach for drug absorption, transport, and retention in the human lungs

Most current models used for modeling the pulmonary drug absorption, transport, and retention are 0D compartmental models where the airways are generally split into the airways and alveolar sections. Such block models deliver low fidelity solutions and the spatial lung drug concentrations cannot be obtained. Other approaches use high fidelity CFD models with limited capabilities due to their exorbitant computational cost. Recently, we presented a novel, fast-running and robust quasi-3D (Q3D) model for modeling the pulmonary airflow. This Q3D method preserved the 3D lung geometry, delivered extremely accurate solutions, and was 25 000 times faster in comparison to the CFD methods. In this paper, we present a Q3D-compartment multiscale combination to model the pulmonary drug absorption, transport, and retention. The initial deposition is obtained from CFD simulations. The lung absorption compartment model of Yu and Rosania is adapted to this multiscale format. The lung is modeled in the Q3D format till the eighth airway generation. The remainder of the lung along with the systemic circulation and elimination processes was modeled using compartments. The Q3D model is further adapted, by allowing for various heterogeneous annular lung layers. This allows us to model the drug transport across the layers and along the lung. Using this multiscale model, the spatiotemporal drug concentrations in the different lung layers and the temporal concentration in the plasma are obtained. The concentration profile in the plasma was found to be better aligned with the experimental findings in comparison with compartmental model for the standard test cases. Thus, this multiscale model can be used to optimize the target-specific drug delivery and increase the localized bioavailability, thereby facilitating applications from the bench to bedside for various patient/lung-disease variations.

Effect of inhaled gas density on the pendelluft-induced lung injury

Helium, sulfur hexafluoride-oxygen, and air were modeled to examine the role of the gas density on the pendelluft-induced lung injury (PILI) under high frequency oscillatory ventilation (HFOV). Large eddy simulation coupled with physiological resistance-compliance boundary conditions was applied to capture pendelluft-induced gas entrapment and mechanical stresses in an image-based human lung model. The flow characteristics were strongly dependent on the inspired gas density. The flow partitioning, globally between the left and right lung and locally between adjacent units branches, was significantly affected by the density of inhaled gas and was more balanced when inspiring lighter gas. The incomplete loops of flow-volume and volume-pressure curves were significantly influenced by the variations of the flow redistribution, resistance, and turbulence associated with the pendelluft mechanism. Inhaling light gas reduced the entrapped gas volume and mechanical stress surrounding carina ridges signifying the important role of inhaled gas properties on PILI. In general, lung ventilation by HFOV with a gas mixture of large amounts of Helium is thought to mitigate ventilator complications.

A biomechanical model of pendelluft induced lung injury

Lung ventilation using high frequency oscillatory techniques have been documented to attain adequate gas exchange through various gas transport mechanisms. Among them, the pendelluft flow is considered one of the most crucial mechanisms. In this work, we computationally investigate the induction of abnormal mechanical stresses and a regionally trapped volume of gas due to pendelluft flow. Large eddy simulation was used to model the turbulence in an upper tracheobronchial lung geometry that was derived from CT scans. The pendelluft flow was captured by modeling physiological boundary conditions at the truncated level of the lung model that is sensitive to the coupled resistance and compliance of individual patients. The flow-volume and volume-pressure loops are characterized by irregular shapes and suggest abnormal regional lung ventilation. Incomplete loops were observed indicating gas trapping in these regions signifying a potential for local injury due to incomplete ventilation from a residual volume build-up at the end of the expiration phase. In addition, the gas exchange between units was observed to create a velocity gradient causing a region of high wall shear stress surrounding the carina ridges. The recurrence of the pendelluft flow could cause a rupture to the lung epithelium layer. The trapped gas and wall shear stress were observed to amplify with increasing compliance asymmetry and ventilator operating frequency. In general, despite the significant contribution of the pendelluft flow to the gas exchange augmentation there exists significant risks of localized lung injury, phenomena we describe as pendelluft induced lung injury or PILI.