Quantifying sustained release kinetics from a polymer matrix including burst effects

Crystallization of carboplatin-loaded onto microporous calcium phosphate using high-vacuum method: Characterization and release study

Drug delivery systems are a new approach to increase therapeutic efficacy and to reduce the side effects of traditional treatments. Calcium phosphates (CaPs) have been studied as drug delivery systems, especially in bone diseases. However, each system has some particularities that depend on the physical and chemical characteristics of the biomaterials and drug interaction. In this work, granulated CaPs were used as a matrix for loading the anticancer drug carboplatin using the high-vacuum method. Five compositions were applied: hydroxyapatite (HA), β-tricalcium phosphate (β-TCP), biphasic HAp 60%/β-TCP 40% (BCP), β-TCP/MgO nanocomposite, and β-TCP/SiO2 nanocomposite. Carboplatin drug in 50, 60, and 70 mg/g was precipitated on the surface of CaPs. Morphological, chemical and surface modifications in the carboplatin-CaPs were investigated by scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), backscattered electron microscopy (BSE), X-ray diffraction (XRD), X-ray fluorescence spectroscopy (XRF), Fourier transform infrared (FT-IR), and Raman spectroscopy. The characterization of the CaP-carboplatin biomaterials showed heterogeneous crystalline precipitation of the drug, and no morphological modifications of the CaPs biomaterials. The in vitro release profile of carboplatin from CaPs was evaluated by the ultraviolet-visible (UV-Vis) method. The curves showed a burst release of upon 60% of carboplatin loaded followed by a slow-release of the drug for the time of the study. The results were typical of a low-interaction system and physisorption mechanism. The high-vacuum method permitted to load the high amount of carboplatin drug on the surface of the biomaterials despite the low interaction between carboplatin and CaPs.

Sinapic acid-loaded chitosan nanoparticles in polycaprolactone electrospun fibers for bone regeneration in vitro and in vivo

Sinapic acid (SA) is a plant-derived phenolic compound known for its multiple biological properties, but its role in the promotion of bone formation is not yet well-studied. Moreover, the delivery of SA is hindered by its complex hydrophobic nature, limiting its bioavailability. In this study, we fabricated a drug delivery system using chitosan nanoparticles (nCS) loaded with SA at different concentrations. These were incorporated into polycaprolactone (PCL) fibers via an electrospinning method. nCS loaded with 50 μM SA in PCL fibers promoted osteoblast differentiation. Furthermore, SA treatment activated the osteogenesis signaling pathways in mouse mesenchymal stem cells. A critical-sized rat calvarial bone defect model system identified that the inclusion of SA into PCL/nCS fibers accelerated bone formation. Collectively, these data suggest that SA promoted osteoblast differentiation in vitro and bone formation in vivo, possibly by activating the TGF-β1/BMP/Smads/Runx2 signaling pathways, suggesting SA might have therapeutic benefits in bone regeneration.

The Use of Cellulose Membrane to Eliminate Burst Release from Intravaginal Rings

Burst release was observed when ethylene vinyl acetate copolymer (EVA) intravaginal rings were tested for progesterone release in our previous work (Helbling et al. Pharm Res. 31(3):795-808, 2014). Burst release is undesirable in controlled delivery devices because release is uncontrollable and higher levels of active pharmaceutical ingredient could lead to the occurrence of adverse effect. The present contribution is about the use of membranes to coat EVA rings to eliminate burst release. Physicochemical state of progesterone in uncoated rings and the solubility and diffusion coefficient in membrane were studied. Hormone delivery from several rings of different sizes was compared. A mathematical model was used to analyze the effects of membrane properties on delivery rate. No chemical interactions were detected between hormone and polymer. Hormone was mainly forming amorphous aggregates inside rings, and migration to membrane was not observed during storage. Diffusion coefficient was smaller in membrane (∼10(-8) cm(2) s(-1)) than in matrix (∼10(-7) cm(2) s(-1)). Zero-order release kinetics were obtained for coated rings, and release rate decreases as the thickness of the coat increases. Cellulose membrane successfully eliminates burst release and controls the delivery from EVA rings. The equations developed can be used to determine the appropriate coat thickness to produce specific release rate.

Nanofibers Fabricated Using Triaxial Electrospinning as Zero Order Drug Delivery Systems

A new strategy for creating functional trilayer nanofibers through triaxial electrospinning is demonstrated. Ethyl cellulose (EC) was used as the filament-forming matrix in the outer, middle, and inner working solutions and was combined with varied contents of the model active ingredient ketoprofen (KET) in the three fluids. Triaxial electrospinning was successfully carried out to generate medicated nanofibers. The resultant nanofibers had diameters of 0.74 ± 0.06 μm, linear morphologies, smooth surfaces, and clear trilayer nanostructures. The KET concentration in each layer gradually increased from the outer to the inner layer. In vitro dissolution tests demonstrated that the nanofibers could provide linear release of KET over 20 h. The protocol reported in this study thus provides a facile approach to creating functional nanofibers with sophisticated structural features.