Nanocomposite proton exchange membranes based on Nafion containing Fe2TiO5 nanoparticles in water and alcohol environments for PEMFC

Sulfonated Polyimide Membranes Derived from a Novel Sulfonated Diamine with Pendant Benzenesulfonic Acid for Fuel Cells

For improving the hydrolytic stability of sulfonated polyimides consisting of five membered anhydrides, novel sulfonated polyimides (NSPIs) were prepared via polymerization of 3,3′,4,4′-benzophenonetetracarboxylic dianhydride (BTDA), with a novel diamine monomer with a pendant sulfonic acid group and 4,4-oxydianiline. Water uptake of this NSPI with an excellent film-forming ability was almost equal to that of Nafion® 117, while their ion exchange capacity (IEC) was 22% higher than Nafion® 117. The loss in weight decreased by 53% and loss in IEC decreased by 66% compared to that of Nafion® 117; both were used to quantitatively measure hydrolytic stability, and radical oxidative stability also increased by 75% when compared with Nafion® 117. Mechanically, this NSPI was superior, and its proton conductivity was higher than Nafion® 117 at elevated temperatures. All these improvements were due to the introduction of this pendant group. Taken together, we herein report a promising renewable energy source based on SPIs capable of displaying proton conductivity and enhanced hydrophilicity.

A Review of Recent Developments and Advanced Applications of High-Temperature Polymer Electrolyte Membranes for PEM Fuel Cells

This review summarizes the current status, operating principles, and recent advances in high-temperature polymer electrolyte membranes (HT-PEMs), with a particular focus on the recent developments, technical challenges, and commercial prospects of the HT-PEM fuel cells. A detailed review of the most recent research activities has been covered by this work, with a major focus on the state-of-the-art concepts describing the proton conductivity and degradation mechanisms of HT-PEMs. In addition, the fuel cell performance and the lifetime of HT-PEM fuel cells as a function of operating conditions have been discussed. In addition, the review highlights the important outcomes found in the recent literature about the HT-PEM fuel cell. The main objectives of this review paper are as follows: (1) the latest development of the HT-PEMs, primarily based on polybenzimidazole membranes and (2) the latest development of the fuel cell performance and the lifetime of the HT-PEMs.

A Review on Ionic Liquids-Based Membranes for Middle and High Temperature Polymer Electrolyte Membrane Fuel Cells (PEM FCs)

Today, the use of polymer electrolyte membranes (PEMs) possessing ionic liquids (ILs) in middle and high temperature polymer electrolyte membrane fuel cells (MT-PEMFCs and HT-PEMFCs) have been increased. ILs are the organic salts, and they are typically liquid at the temperature lower than 100 °C with high conductivity and thermal stability. The membranes containing ILs can conduct protons through the PEMs at elevated temperatures (more than 80 °C), unlike the Nafion-based membranes. A wide range of ILs have been identified, including chiral ILs, bio-ILs, basic ILs, energetic ILs, metallic ILs, and neutral ILs, that, from among them, functionalized ionic liquids (FILs) include a lot of ion exchange groups in their structure that improve and accelerate proton conduction through the polymeric membrane. In spite of positive features of using ILs, the leaching of ILs from the membranes during the operation of fuel cell is the main downside of these organic salts, which leads to reducing the performance of the membranes; however, there are some ways to diminish leaching from the membranes. The aim of this review is to provide an overview of these issues by evaluating key studies that have been undertaken in the last years in order to present objective and comprehensive updated information that presents the progress that has been made in this field. Significant information regarding the utilization of ILs in MT-PEMFCs and HT-PEMFCs, ILs structure, properties, and synthesis is given. Moreover, leaching of ILs as a challenging demerit and the possible methods to tackle this problem are approached in this paper. The present review will be of interest to chemists, electrochemists, environmentalists, and any other researchers working on sustainable energy production field.

Fabrication and performance evaluation of new nanocomposite membranes based on sulfonated poly(phthalazinone ether ketone) for PEM fuel cells

The purpose of this work is to enhance the proton conductivity and fuel cell performance of sulfonated poly(phthalazinone ether ketone) (SPPEK) as a proton exchange membrane through the application of SrTiO₃ perovskite nanoparticles. Nanocomposite membranes based on SPPEK and SrTiO₃ perovskite nanoparticles were prepared via a casting method. The highest proton conductivity of nanocomposite membranes obtained was 120 mS cm⁻¹ at 90 °C and 95% RH. These enhancements could be related to the hygroscopic structure of SrTiO₃ perovskite nanoparticles and the formation of hydrogen bonds between nanoparticles and water molecules. The satisfactory power density, 0.41 W cm⁻² at 0.5 V and 85 °C, of the nanocomposite membrane (5 wt% content of nanoparticles) confirms their potential for application in the PEM fuel cells.

The purpose of this work is to enhance the proton conductivity and fuel cell performance of sulfonated poly(phthalazinone ether ketone) (SPPEK) as a proton exchange membrane through the application of SrTiO₃ perovskite nanoparticles.

High temperature composite membranes based on polybenzimidazole and dendrimer amine functionalized SBA-15 mesoporous silica for fuel cells

In this work SBA-15, a melamine-based functionalized SBA-15 mesoporous silica with a dicationic ionic liquid was used in order to improve the physicochemical properties of phosphoric acid doped polybenzimidazole membranes for application in HT-PEMFCs.

Polybenzimidazole/BaCe0.85Y0.15O3-δ nanocomposites with enhanced proton conductivity for high-temperature PEMFC application

The present work reports the synthesis of polybenzimidazole (PBI)/BaCe0.85Y0.15O3-δ nanocomposite membrane. The obtained membranes were investigated to use as novel electrolytes in high-temperature proton exchange fuel cells. The PBCYx membranes were prepared with dispersing BaCe0.85Y0.15O3-δ into the polyimidazole membrane by solution casting method. The obtained membranes were used as novel proton conductors. The thermal stability and structural properties were investigated. The conductivity and morphology of the obtained materials were studied using impedance spectroscopy AC (IS) and a scanning electron microscope (SEM) equipped with energy dispersive X-ray spectroscopy (EDX). The maximum phosphoric acid adsorption (175%) and protonic conductivity (0.092 S/cm at 180 °C under dry conditions) were observed for all of the PBI nanocomposite membranes containing 5 wt.% of BaCe0.85Y0.15O3-δ in the membrane matrix. The polarization and power density curves were studied at 150 and 180 °C operating temperatures. The power density of about 0.42 W/cm2 and current density of about 0.84 A/cm at 0.5 V and 180 °C were achieved under dry conditions. The data obtained from our studies showed that the physicochemical properties of the novel nanocomposites were enhanced for using in the high-temperature proton transfer fuel cells.

Optimization of reaction parameters affecting crystal phase growth and purity of BaCeO3 and BaCe1-xYbxO3-δ nanopowders and investigating high protonic conductivity of sulfonated poly(ether ether ketone) – BaCe0.85Yb0.15O3-δ composite membrane

Pure and ytterbium-doped BaCeO3 nanostructures were synthesized by solid-state reaction with the mixtures of Ba(NO3)2, BaCO3, (NH4)2Ce(NO3)6, and Yb2O3 at 800 °C for 10 and 24 h. Doping of ytterbium ions in the BaCeO3 host matrix has been studied and confirmed using powder X-ray diffraction. The results from the Rietveld analysis indicated that the sample has a main BaCeO3 structure with the space group of [Formula: see text]. Through intensive experiments and analysis, optimum reaction conditions for the synthesis of doped nanoparticles including the crystal phase impurity and reaction time are proposed. The results of the study showed that for the reaction time of 24 h, BaCO3 reacted more effectively with (NH4)2Ce(NO3)6 than Ba(NO3)2 did. On the other hand, the purity values of 97% and 95% were obtained for pure and Yb3+ doped BaCeO3 samples, respectively. Field emission scanning electron microscope images revealed that the synthesized BaCeO3 nanomaterials have mono-shaped sphere morphology. Furthermore, ytterbium-doped nanoparticles were incorporated into the matrix of sulfonated poly(ether ether ketone) (SPEEK) membranes (SPYb) with the aim of enhancing proton conductivity. The prepared SPYb nanocomposite membrane containing 1.7 wt.% of BaCe0.85Yb0.15O3-δ nanoparticles exhibited a high proton conductivity (67 mS/cm) at 80 °C.

A highly proton-/vanadium-selective perfluorosulfonic acid membrane for vanadium redox flow batteries

The polar clusters of Nafion are blocked by the incorporation of the nanohybrid, which contributes to suppress vanadium ions crossover.

Synthesis and optimization of nanocomposite membranes based on SPEEK and perovskite nanoparticles for polymer electrolyte membrane fuel cells

The addition of BaZr_0.9Y_0.1O_3−δ (BZY10) nanoparticles as a perovskite material with a proton conductor oxide structure to enhance the performance of sulfonated poly(ether ether ketone) (SPEEK) in proton exchange membrane fuel cells (PEMFCs) has been investigated in this work.

Enhancing the performance of SPEEK polymer electrolyte membranes using functionalized TiO2 nanoparticles with proton hopping sites

In this work, the application of a sulfonated poly(ether ether ketone) (SPEEK)/amine functionalized titanium dioxide nanoparticle (AFT) composite as a novel membrane in proton exchange membrane fuel cells (PEMFC) was studied.

Novel Composite PEM with Long-Range Ionic Nanochannels Induced by Carbon Nanotube/Graphene Oxide Nanoribbon Composites

In the current study, carbon nanotube/graphene oxide nanoribbon (CNT/GONR) composites were obtained via a chemical "unzipping" method. Then novel CNT/GONR Nafion composite proton exchange membranes (PEMs) were prepared via a blending method. The CNT/GONR nanocomposites induce the adjustment of (-SO₃^-)_n ionic clusters in Nafion matrix to construct long-range ionic nanochannels and keep the activity of ionic clusters at the same time. This dramatically promotes the proton transport of the CNT/GONR Nafion composite PEMs at low humidity and high temperature. The proton conductivity of the composite PEM with 0.5 wt % CNT/GONR is as high as 0.18 S·cm^-1 at 120 °C and 40%RH, nine times of recast Nafion (0.02 S·cm^-1) at the same conditions. The 1D/2D nanostructure of CNT/GONR nanocomposite also contributes to restrain the methanol permeability of CNT/GONR Nafion. The composite PEM shows a one-order-of-magnitude decrease (2.84 × 10^-09 cm²·s^-1) in methanol permeability at 40 °C. Therefore, incorporation of this 1D/2D nanocomposite into Nafion PEM is a feasible pathway to conquer the trade-off effect between proton conductivity and methanol resistance.

Surface modification of Fe2TiO5 nanoparticles by silane coupling agent: Synthesis and application in proton exchange composite membranes

Modifying surfaces of nanoparticles with silane coupling agent provides a simple method to alter their surface properties and improve their dispersibility in organic solvents and polymer matrix. Fe2TiO5 nanoparticles (IT) were modified with 3-aminopropyltriethoxysilane (APTES) as novel reinforcing filler for proton exchange membranes. The main operating parameters such as reaction time (R.T), APTES/IT and triethylamine (TEA)/IT ratios have been optimized for maximum grafting efficiency. The optimum conditions for R.T, APTES/IT and TEA/IT ratios were 6h, 4 and 0.3 respectively. It was observed that the APTES/IT and TEA/IT ratios were the most significant parameters affecting the grafting percentage. Modified nanoparticles were characterized using FT-IR, TGA, SEM, TEM and XRD techniques. Effects of modified nanoparticles in proton exchange membrane fuel cells (PEMFC) were evaluated. The resulting nanocomposite membranes exhibited higher proton conductivity in comparison with pristine SPPEK and SPPEK/IT membranes. This increase is attributed to connectivity of the water channels which creates more direct pathways for proton transport. Composite membrane with 3% AIT (6.46% grafting amount) showed 0.024 S cm(-1) proton conductivity at 25 °C and 149 mW cm(-2) power density (at 0.5V) at 80 °C which were about 243% and 51%, respectively higher than that of pure SPPEK.

Preparation and evaluation of Nafion/SnO2 nanocomposite for improving the chemical durability of proton exchange membranes in fuel cells

A composite Nafion-based membrane using SnO₂ nanoparticles as a radical scavenger was firstly investigated. The Nafion/SnO₂ nanocomposite membrane exhibits more chemical durability than the pure Nafion membrane.

Novel nanocomposite membranes based on blended sulfonated poly(ether ether ketone)/poly(vinyl alcohol) containing sulfonated graphene oxide/Fe3O4 nanosheets for DMFC applications

Presumptive representation structure of the prepared cross-linked nanocomposite proton exchange membrane.