Mussel-inspired modification of ion exchange membrane for monovalent separation

The Potential of Electrodialysis with Mediating Solution (EDM) for Eliminating Alkaline Scaling: Experimental Validation and Mechanistic Elucidation

Alkaline scaling in the cathode chambers of conventional electrodialysis (ED) stacks presents significant challenges when desalinating solutions containing divalent cations. This scaling, resulting from the combined effects of water electrolysis and the migration of divalent cations from the feedwater into the catholyte, further extends from the cathode chamber to the surfaces of both the cation exchange membrane (CEM) and the anion exchange membrane (AEM) in the adjacent dilute chamber. This study aims to mitigate alkaline scaling, without pretreatment or antiscalant dosing, by optimizing the ED stack design to restrict divalent cation transport toward the cathode. We evaluated three ED stack configurations, each forming the cathode chamber with a distinct ion transport control mechanism: (1) a monovalent selective cation exchange membrane (SCEM), (2) a bipolar membrane (BPM), and (3) a mediating solution chamber adjacent to the cathode chamber (EDM). Our results indicated that stacks employing the SCEM or BPM partially restricted divalent cation migration but remained vulnerable to scaling under higher feed salinities, due to weakened Donnan exclusion within the SCEM, and strong internal ion polarization at the BPM interface. In contrast, the EDM stack exhibited superior antiscaling performance by combining strong Donnan exclusion through an AEM with ionic buffering in the mediating solution chamber, effectively blocking cation transport and eliminating conditions conducive to scaling. Additionally, the EDM stack maintained low electrical resistance and high operational stability, making it a simple, efficient, and cost-effective solution for scaling mitigation in ED systems.

Valorization of Seawater Reverse Osmosis Brine by Monovalent Ion-Selective Membranes through Electrodialysis

This paper proposes the use of monovalent selective electrodialysis technology to concentrate the valuable sodium chloride (NaCl) component present in seawater reverse osmosis (SWRO) brine for direct utilization in the chlor-alkali industry. To enhance monovalent selectivity, a polyamide selective layer was fabricated on commercial ion exchange membranes (IEMs) through interfacial polymerization (IP) of piperazine (PIP) and 1,3,5-Benzenetricarbonyl chloride (TMC). The IP-modified IEMs were characterized using various techniques to investigate changes in chemical structure, morphology, and surface charge. Ion chromatography (IC) analysis showed that the divalent rejection rate was more than 90% for IP-modified IEMs, compared to less than 65% for commercial IEMs. Electrodialysis results demonstrated that the SWRO brine was successfully concentrated to 14.9 g/L NaCl at a power consumption rate of 3.041 kWh/kg, indicating the advantageous performance of the IP-modified IEMs. Overall, the proposed monovalent selective electrodialysis technology using IP-modified IEMs has the potential to provide a sustainable solution for the direct utilization of NaCl in the chlor-alkali industry.

Forward osmosis membrane doped with water-based zirconium fumarate MOFs to enhance dye pollutant removal and membrane antifouling performance

Metal-organic frameworks (MOFs) can be applied to enhance the property of forward osmosis membranes. However, organic solvents can easily remain in organic synthetic metal-organic frame materials and cause membrane fouling and a decrease in membrane permeability. In this study, water-based Zr-fumarate MOFs were synthesized and doped into the membrane active layer by interfacial polymerization to provide a water-based MOF-doped thin-film composite membrane (TFC membrane). It was found that doping the water-based MOFs effectively improved membrane hydrophilicity, and nanowater passages were introduced in the active layer to improve permeability. The water flux of the water-based MOF-doped TFC membranes was increased by 21% over that of the original membrane, and the selectivity performance of the membrane was improved while keeping the salt rejection basically unchanged. Additionally, the water-based MOF-doped TFC membrane showed good removal efficiency (R_d > 94%) and strong antipollution performance in the treatment of dye pollutants.

Effect of the bio-inspired modification of low-cost membranes with TiO2:ZnO as microbial fuel cell membranes

Microbial fuel cells (MFCs) are a novel technique for converting biodegradable materials into electricity. In this study, the efficiency of mixed crystal (TiO₂:ZnO) as a membrane modifier of a low-cost, antifouling and self-cleaning cation exchange membrane for MFCs was studied. The modification was prepared using polydopamine (PDA) as the bio-inspired glue, followed by gravity deposition of a mixture of catalyst nanoparticles (TiO₂:ZnO 0.03%, 1:1 ratio) as anti-biofouling agents. The effects of the membrane modification were evaluated in terms of power density, open circuit potential, coulombic efficiency, anti-biofouling properties and also color and COD removal efficiency. The results showed that the use of the PDA-modified membrane and a mixture of catalysts facilitated the transfer of cations released during the oxidation process in the anodic compartment of the MFC, which increased the power generation in the MFC by 2.5 times and 5.7 times the current compared to pristine and PDA pristine membranes, decreased the MFC operating cycle time from 5 to 3 days, doubled the lifetime of the membranes and demonstrated higher COD removal efficiency and color removal. Finally, SEM and AFM analysis showed that the modification significantly minimized surface fouling. The modified membranes in this study proved to be a potential alternative to the expensive membranes currently used in MFCs, furthermore, this modification could be an interesting alternative modification for other potential membranes for use in MFCs, due to the fact that the catalyst activation was only performed with visible light (artificial and solar), which could decrease operating costs.

A Facile Co-Deposition Approach to Construct Functionalized Graphene Quantum Dots Self-Cleaning Nanofiltration Membranes

In this study, a novel photocatalytic self-cleaning nanofiltration (NF) membrane was fabricated by constructing aspartic acid-functionalized graphene quantum dots (AGQDs) into the polydopamine/polyethyleneimine (PDA/PEI) selective layer via the co-deposition method. The chemical composition, microstructure, and hydrophilicity of the prepared membranes were characterized by scanning electron microscopy (SEM), atomic force microscopy (AFM), attenuated total reflection (ATR-FTIR), X-ray photoelectron spectroscopy (XPS), and water contact angle (WCA). Meanwhile, the effects of PEI molecular weight and AGQDs concentration on NF membrane structures and separation performance were systematically investigated. The photocatalytic self-cleaning performance of the PDA/PEI/AGQDs membrane was evaluated in terms of flux recovery rate. For constructing high-performance NF membranes, it is found that the optimal molecular weight of PEI is 10,000 Da, and the optimal concentration of AGQDs is 2000 ppm. The introduction of hydrophilic AGQDs formed a more hydrophilic and dense selective layer during the co-deposition process. Compared with the PDA/PEI membrane, the engineered PDA/PEI/AGQDs NF membrane has enhanced water flux (55.5 LMH·bar^-1) and higher rejection (99.7 ± 0.3% for MB). In addition, the PDA/PEI/AGQDs membrane exhibits better photocatalytic self-cleaning performance over the PDA/PEI membrane (83% vs. 69%). Therefore, this study provides a facile approach to construct a self-cleaning NF membrane.

Well-defined hollow tube@sheets NiCo2S4 core-shell nanoarrays for ultrahigh capacitance supercapacitor

Reasonable design of electrodes with well-defined nanostructure is the central aspect in the practical application of high-performance supercapacitors. Herein, hollow tube@sheets NiCo₂S₄ core-shell nanoarrays are rationally constructed to the free-standing electrode by in situ growing ZIF-67 on Co-precursor nanorods array and sequentially performing anion-exchange (S^2-) and cation-exchange (Ni²⁺). The well-defined nanostructures can shorten the ion transport path in the charging-discharging process, increase the specific surface area and electrochemical active cites, which help in improving electrochemical performance. Therefore, the unique tube@sheets NiCo₂S₄ core-shell nanoarrays exhibit intriguing electrochemical performance and show excellent areal capacitance of 11.3 F cm^-2 (3227.94 F g^-1) at a current density of 2 mA cm^-2 (2 A g^-1). The assembled asymmetric supercapacitor device delivers a high energy density of 0.42 mW h cm^-2 at a power density of 2.1 mW cm^-2 and displays outstanding cyclic stability (90.2% retention after 5000 cycles). Consequently, the well-defined nanostructure engineering strategy is beneficial for designing active electrode materials for efficient energy storage devices.

Facile fabrication of zeolitic imidazolate framework hollow fibre membranes via a novel scalable continuous fluid circulation process

A novel continuous fluid circulation system was designed and employed for the impregnation seeding and fabrication of zeolitic imidazolate framework (ZIF) crystals on the internal surface of polymeric hollow fibre membranes. Application of impregnation seeding has been proven effective to decrease crystal size, consequently increasing surface roughness and wettability of the membrane. Evaluation of the as-synthesised membrane demonstrated excellent separation efficiencies (>99%) of surfactant stabilised oil-in-water emulsions. Owing to the simple impregnation strategy assisted by the continuous fluid circulation, the active ZIF layer formed was visibly thinner and denser than typical seeding techniques, hence a high pure water flux of >1150 L m^-2 h^-1 bar^-1 was achieved. The membranes were highly selective and ultra-permeable to water, however, almost impermeable to oils in a water environment, e.g., n-hexane, n-heptane, chloroform and dichloromethane, as well as their emulsion mixtures, with a separation efficiency higher than 99%. Besides, this new continuous fluid circulation method was also found promising for the synthesis of other types of ZIF on hollow fibre membranes.

Cation Exchange Membranes Coated with Polyethyleneimine and Crown Ether to Improve Monovalent Cation Electrodialytic Selectivity

Developing monovalent cation permselective membranes (MCPMs) with high-efficient permselectivity is the core concern in specific industrial applications. In this work, we have fabricated a series of novel cation exchange membranes (CEMs) based on sulfonated polysulfone (SPSF) surface modification by polyethyleneimine (PEI) and 4′-aminobenzo-12-crown-4 (12C4) codeposited with dopamine (DA) successively, which was followed by the cross-linking of glutaraldehyde (GA). The as-prepared membranes before and after modification were systematically characterized with regard to their structures as well as their physicochemical and electrochemical properties. Particularly, the codeposition sequence of modified ingredients was investigated on galvanostatic permselectivity to cations. The modified membrane (M-12C4-0.50-PEI) exhibits significantly prominent selectivity to Li⁺ ions (PMg2+Li+ = 5.23) and K⁺ ions (PMg2+K+ = 13.56) in Li⁺/Mg²⁺ and K⁺/Mg²⁺ systems in electrodialysis (ED), which is far superior to the pristine membrane (M-0, PMg2+Li+ = 0.46, PMg2+K+ = 1.23) at a constant current density of 5.0 mA·cm⁻². It possibly arises from the synergistic effects of electrostatic repulsion (positively charged PEI), pore-size sieving (distribution of modified ingredients), and specific interaction effect (12C4 ~Li⁺). This facile strategy may provide new insights into developing selective CEMs in the separation of specific cations by ED.

Impact of MWCO and Dopamine/Polyethyleneimine Concentrations on Surface Properties and Filtration Performance of Modified Membranes

The mussel-inspired method has been investigated to modify commercial ultrafiltration membranes to induce antifouling characteristics. Such features are essential to improve the feasibility of using membrane processes in protein recovery from waste streams, wastewater treatment, and reuse. However, some issues still need to be clarified, such as the influence of membrane pore size and the polymer concentration used in modifying the solution. The aim of the present work is to study a one-step deposition of dopamine (DA) and polyethyleneimine (PEI) on ultrafiltration membrane surfaces. The effects of different membrane molecular weight cut-offs (MWCO, 20, 30, and 50 kDa) and DA/PEI concentrations on membrane performance were assessed by surface characterization (FTIR, AFM, zeta potential, contact angle, protein adsorption) and permeation of protein solution. Results indicate that larger MWCO membranes (50 kDa) are most benefited by modification using DA and PEI. Moreover, PEI is primarily responsible for improving membrane performance in protein solution filtration. The membrane modified with 0.5:4.0 mg mL^-1 (DA: PEI) presented a better performance in protein solution filtration, with only 15% of permeate flux drop after 2 h of filtration. The modified membrane can thus be potentially applied to the recovery of proteins from waste streams.

PVA-Based Mixed Matrix Membranes Comprising ZSM-5 for Cations Separation

The traditional ion-exchange membranes face the trade-off effect between the ion flux and perm-selectivity, which limits their application for selective ion separation. Herein, we amalgamated various amounts of the ZSM-5 with the polyvinyl alcohol as ions transport pathways to improve the permeability of monovalent cations and exclusively reject the divalent cations. The highest contents of ZSM-5 in the mixed matrix membranes (MMMs) can be extended up to 60 wt% while the MMMs with optimized content (50 wt%) achieved high perm-selectivity of 34.4 and 3.7 for H⁺/Zn²⁺ and Li⁺/Mg²⁺ systems, respectively. The obtained results are high in comparison with the commercial CSO membrane. The presence of cationic exchange sites in the ZSM-5 initiated the fast transport of proton, while the microporous crystalline morphology restricted the active transport of larger hydrated cations from the solutions. Moreover, the participating sites and porosity of ZSM-5 granted continuous channels for ions electromigration in order to give high limiting current density to the MMMs. The SEM analysis further exhibited that using ZSM-5 as conventional fillers, gave a uniform and homogenous formation to the membranes. However, the optimized amount of fillers and the assortment of a proper dispersion phase are two critical aspects and must be considered to avoid defects and agglomeration of these enhancers during the formation of membranes.

Physico-chemical processes

The review scans research articles published in 2018 on physico-chemical processes for water and wastewater treatment. The paper includes eight sections, that is, membrane technology, granular filtration, flotation, adsorption, coagulation/flocculation, capacitive deionization, ion exchange, and oxidation. The membrane technology section further divides into six parts, including microfiltration, ultrafiltration, nanofiltration, reverse osmosis/forward osmosis, and membrane distillation. PRACTITIONER POINTS: Totally 266 articles on water and wastewater treatment have been scanned; The review is sectioned into 8 major parts;  Membrane technology has drawn the widest attention from the research community.

Expanding the DOPA Universe with Genetically Encoded, Mussel-Inspired Bioadhesives for Material Sciences and Medicine

Catechols are a biologically relevant group of aromatic diols that have attracted much attention as mediators of adhesion of "bio-glue" proteins in mussels of the genus Mytilus. These organisms use catechols in the form of the noncanonical amino acid l-3,4-dihydroxyphenylalanine (DOPA) as a building block for adhesion proteins. The DOPA is generated post-translationally from tyrosine. Herein, we review the properties, natural occurrence, and reactivity of catechols in the design of bioinspired materials. We also provide a basic description of the mussel's attachment apparatus, the interplay between its different molecules that play a crucial role in adhesion, and the role of post-translational modifications (PTMs) of these proteins. Our focus is on the microbial production of mussel foot proteins with the aid of orthogonal translation systems (OTSs) and the use of genetic code engineering to solve some fundamental problems in the bioproduction of these bioadhesives and to expand their chemical space. The major limitation of bacterial expression systems is their intrinsic inability to introduce PTMs. OTSs have the potential to overcome these challenges by replacing canonical amino acids with noncanonical ones. In this way, PTM steps are circumvented while the genetically programmed precision of protein sequences is preserved. In addition, OTSs should enable spatiotemporal control over the complex adhesion process, because the catechol function can be masked by suitable chemical protection. Such caged residues can then be noninvasively unmasked by, for example, UV irradiation or thermal treatment. All of these features make OTSs based on genetic code engineering in reprogrammed microbial strains new and promising tools in bioinspired materials science.

Stiffness of Aligned Fibers Regulates the Phenotypic Expression of Vascular Smooth Muscle Cells

Electrospun uniaxially aligned ultrafine fibers show great promise in constructing vascular grafts mimicking the anisotropic architecture of native blood vessels. However, understanding how the stiffness of aligned fibers would impose influences on the functionality of vascular cells has yet to be explored. The present study aimed to explore the stiffness effects of electrospun aligned fibrous substrates (AFSs) on phenotypic modulation in vascular smooth muscle cells (SMCs). A stable jet coaxial electrospinning (SJCES) method was employed to generate highly aligned ultrafine fibers of poly(l-lactide- co-caprolactone)/poly(l-lactic acid) (PLCL/PLLA) in shell-core configuration with a remarkably varying stiffness region from 0.09 to 13.18 N/mm. We found that increasing AFS stiffness had no significant influence on the cellular shape and orientation along the fiber direction with the cultured human umbilical artery SMCs (huaSMCs) but inhibited the cell adhesion rate, promoted cell proliferation and migration, and especially enhanced the F-actin fiber assembly in the huaSMCs. Notably, higher fiber stiffness resulted in significant downregulation of contractile markers like alpha-smooth muscle actin (α-SMA), smooth muscle myosin heavy chain, calponin, and desmin, whereas upregulated the gene expression of pathosis-associated osteopontin ( OPN) in the huaSMCs. These results allude to the phenotype of huaSMCs on stiffer AFSs being miserably modulated into a proliferative and pathological state. Consequently, it adversely affected the proliferation and migration behavior of human umbilical vein endothelial cells as well. Moreover, stiffer AFSs also revealed to incur significant upregulation of inflammatory gene expression, such as interleukin-6 ( IL-6), monocyte chemoattractant protein-1 ( MCP-1), and intercellular adhesion molecule-1 ( ICAM-1), in the huaSMCs. This study stresses that although electrospun aligned fibers are capable of modulating native-like oriented cell morphology and even desired phenotype realization or transition, they might not always direct cells into correct functionality. The integrated fiber stiffness underlying is thereby a critical parameter to consider in engineering structurally anisotropic tissue-engineered vascular grafts to ultimately achieve long-term patency.