A novel method for the fabrication of silver nanowires-based highly electro-conductive membrane with antifouling property for efficient microalgae harvesting

Optimizing electroactive membrane performance for microalgae harvesting: A response surface methodology study of membrane formulation and operating parameters for electro filtration

Developing electroactive membranes for filtration has gained importance owing to their effectiveness in mitigating the long-lasting issue of fouling faced with traditional membranes. Here, we developed thin electroactive metallic films on to stainless steel mesh (SSM) using electrodeposition method and evaluated their performance for microalgae harvesting via electro filtration. The effect of electrodeposition parameters on membrane formulation and operating parameters for electro filtration, both in continuous and intermittent modes, were evaluated and optimum values were obtained using response surface methodology (RSM). The optimal combination of electrodeposition parameters is 1000 μA/cm2 and 5 min for deposition current density and time, respectively. Whereas the electric field strength of 20 V/mm with an application time of 1 min is suggested to be the optimal combination of electro filtration parameters for maximized flux recovery and corresponding experimental rejection efficiency of more than 90%. Overall, this research contributes to a better understanding of the parameters governing electro-filtration and offers insights for improving the performance of membrane-based microalgae harvesting systems.

Membrane processes enhanced by various forms of physical energy: A systematic review on mechanisms, implementation, application and energy efficiency

Membrane technologies in water and wastewater treatment have been eagerly pursued over the past decades, yet membrane fouling remains the major bottleneck to overcome. Membrane fouling control methods which couple membrane processes with online in situ application of external physical energy input (EPEI) are getting closer and closer to reality, thanks to recent advances in novel materials and energy deliverance methods. In this review, we summarized recent studies on membrane fouling control techniques that depend on (i) electric field, (ii) acoustic field, (iii) magnetic field, and (iv) photo-irradiation (mostly ultraviolet or visible light). Mechanisms of each energy input were first reported, which defines the applicability of these methods to certain wastewater matrices. Then, means of implementation were discussed to evaluate the compatibility of these fouling control methods with established membrane techniques. After that, preferred applications of each energy input to different foulant types and membrane processes in the experiment reports were summarized, along with a discussion on the trends and knowledge gaps of such fouling control research. Next, specific energy consumption in membrane fouling control and flux enhancement was estimated and compared, based on the experimental results reported in the literature. Lastly, strength and weakness of these methods and future perspectives were presented as open questions.

Novel metallic stainless-steel mesh-supported conductive membrane and its performance in the electro-filtration process

In this study, we demonstrate the fabrication of a thoroughly metallic electro-conductive membrane by using simple filtration to uniformly coat AgNWs dispersion through stainless steel (SUS)-mesh, which functions both as filter and a flexible conductive substrate. The as-prepared AgNWs networks layer on the SUS-mesh was further strengthened by electroplating Ag layers (P-SUS membrane); exhibiting an overall electrical conductivity of 9.2 × 10⁴ S/m, which is up to 42 times greater than the conductivity of pristine SUS-mesh. The P-SUS membrane exhibited adequate physical durability against chemical and mechanical stresses under prolonged filtration, and high pure water flux of 534 ± 54 LMH/bar. This electro-membrane displayed the anticipated flux recovery in harvesting microalgae (Chlorella sp. HS-2) when filtration was done with the membrane used as a cathode: micro-sized bubbles, generated from the cathodic membrane, functioned to detach the foulants and recover the relative flux to a significant level. The P-SUS membrane indeed possesses necessary traits that the polymer-support membrane lacks, in terms of not only electrical conductivity and mechanical strength but also filtration performance with anti-fouling capability, all of which are of necessity to be considered workable electroconductive membrane.

Purifying water with silver nanoparticles (AgNPs)-incorporated membranes: Recent advancements and critical challenges

In the face of the growing global water crisis, membrane technology is a promising means of purifying water and wastewater. Silver nanoparticles (AgNPs) have been widely used to improve membrane performance, for antibiofouling, and to aid in photocatalytic degradation, thermal response, and electro-conductivity. However, several critical issues such as short antimicrobial periods, trade-off effects and silver inactivation seriously restrict the engineering application of AgNPs-incorporated membranes. In addition, there is controversy around the use of AgNPs given the toxic preparation process and environmental/biological risks. Hence, it is of great significance to summarize and analyze the recent developments and critical challenges in the use of AgNPs-incorporated membranes in water and wastewater treatment, and to propose potential solutions. We reviewed the different properties and functions of AgNPs and their corresponding applications in AgNPs-incorporated membranes. Recently, multifunctional, novel AgNP-incorporated membranes combined with other functional materials have been developed with high-performance. We further clarified the synergistic mechanisms between AgNPs and these novel nanomaterials and/or polymers, and elucidated their functions and roles in membrane separation. Finally, the critical challenges of AgNPs-incorporated membranes and the proposed solutions were outlined: i) Prolonging the antimicrobial cycle through long-term and controlled AgNPs release; ii) Overcoming the trade-off effect and organic fouling of the AgNPs-incorporated membranes; iii) Preparation of sustainable AgNPs-incorporated membranes; iv) Addressing biotoxicity induced by AgNPs; and v) Deactivation of AgNPs-incorporated membrane. Overall, this review provides a comprehensive discussion of the advancements and challenges of AgNPs-incorporated membranes and guides the development of more robust, multi-functional and sustainable AgNPs-incorporated membranes.

A critical review on classifications, characteristics, and applications of electrically conductive membranes for toxic pollutant removal from water: Comparison between composite and inorganic electrically conductive membranes

Research efforts have recently been directed at developing electrically conductive membranes (EMs) for pressure-driven membrane separation processes to remove effectively the highly toxic pollutants from water. EMs serve as both the filter and the electrode during filtration. With the assistance of a power supply, EMs can considerably improve the toxic pollutant removal efficiency and even realize chemical degradation to reduce their toxicity. Organic-inorganic composite EMs and inorganic EMs show remarkable differences in characteristics, removal mechanisms, and application situations. Understanding their differences is highly important to guide the future design of EMs for specific pollutant removal from water. However, reviews concerning the differences between composite and inorganic EMs are still lacking. In this review, we summarize the classifications, fabrication techniques, and characteristics of composite and inorganic EMs. We also elaborate on the removal mechanisms and performances of EMs toward recalcitrant organic pollutants and toxic inorganic ions in water. The comparison between composite and inorganic EMs is emphasized particularly in terms of the membrane characteristics (pore size, permeability, and electrical conductivity), application situations, and underlying removal mechanisms. Finally, the energy consumption and durability of EMs are evaluated, and future perspectives are presented.

The performance of electrode ultrafiltration membrane bioreactor in treating cosmetics wastewater and its anti-fouling properties

The membrane fouling problem of the membrane bioreactor (MBR) for wastewater treatment reduces the membrane flux and the pollutants removal efficiencies, which is the major obstacle limiting its application and should be properly solved. The combination of membrane and electricity can effectively slow down the membrane fouling rate due to electric repulsion between the pollutants and the membrane. In this study, the performance and the membrane fouling features of an electrode ultrafiltration membrane bioreactor (EMBR) fed with cosmetics wastewater were compared with a conventional ultrafiltration membrane bioreactor (UMBR). The results showed the COD removal efficiency increased by 4.43% and the transmembrane pressure (TMP) reduced by 50% in the EMBR as compared with the UMBR. The specific surface areas of electrode ultrafiltration membrane and conventional ultrafiltration membrane declined by 56.9% and 78.8% after 90 days of operation, respectively. The Protein (PN), polysaccharide (PS) and humic acids (HA) in the cake layer of EMBR were only 61.27%, 78.37% and 34.85% of that of UMBR, which contributed to its loose and porous structure and thus decreased the growth rate of TMP and extended the operation cycle. Extended Derjaguin-Landau-Verwey-Overbeek (XDLVO) theory calculation proved that the energy barrier between the electrode ultrafiltration membrane and the pollutants was 50% higher than that between the conventional ultrafiltration membrane and the pollutants. Therefore, the strong anti-fouling property of the electrode ultrafiltration membrane could reduce the chemicals dosage and manpower consumption for membrane cleaning and could be preferred for the treatment of cosmetics or alike wastewater containing high concentrations of surfactants and fatty acids.

Aluminum sheet induced flower-like carbon nitride anchored with silver nanowires for highly efficient SERS detection of trace malachite green

The sensitive detection of malachite green (MG) in aquaculture wastewater is necessary for its residual poses a great threat to the living systems. Herein, the flower-like C₃N₄ (f-C₃N₄) nanostructure induced by Al sheet in the hydrothermal process is constructed. Subsequently, Ag nanowires (AgNWs) supported on Al/f-C₃N₄ and the strong interaction between AgNWs and Al/f-C₃N₄ are confirmed by XPS, Raman spectroscopy, UV-vis diffuse reflectance and fluorescence spectroscopy. Importantly, the portable Al/f-C₃N₄/AgNWs substrate shows the outstanding SERS response for MG, which is attributed to enhanced electromagnetic effect of AgNWs on large amount of corrugated and creviced regions in the flower-like Al/f-C₃N₄ and the charge transfer among the components. Also, the prepared Al/f-C₃N₄ nanostructure provides large specific surface area and abundant "N" active sites for AgNWs, and the high enrichment ability of Al/f-C₃N₄ towards MG molecules by the strong π-π stacking interaction. The detection limit of Al/f-C₃N₄/AgNWs for MG is as low as 8.38 × 10^-12 mol L^-1. The substrate can be reproduced and reused for at least 7 cycles, and the activity can still be kept after laid up for 49 days. Importantly, it unfolds a good sensitivity and selectivity for MG in actual water sample. Results indicate that the Al/f-C₃N₄/AgNWs substrate has a promising potential in practical application for trace detection of MG.

Electro-Fenton improving fouling mitigation and microalgae harvesting performance in a novel membrane photobioreactor

An innovative electro-Fenton enhanced membrane photobioreactor with satisfactory membrane fouling mitigation was constructed for microalgae harvesting. The porous carbon and carbon nanotubes hollow fiber membranes (PC-CHFMs) were used as the separation unit and cathode, simultaneously. H₂O₂ was generated by cathode reducing O₂ in-situ, which would further produce •OH as the main oxidant by coupling H₂O₂ with Fe²⁺. The •OH could deeply remove the extracellular organic matter (EOM) deposited on the membrane surface or inside the pores. Experimental results showed that the permeate flux recovery rates of PC-CHFMs by electro-Fenton at the 18th, 29th and 41st day were 100%, 100% and 98.3%, respectively. The corresponding recovery rates by chemical cleaning at the same time were 99.8%, 81.7% and 54.4%. The stable and high permeate flux of PC-CHFMs made a great contribution to the microalgae harvesting efficiency, where the concentration factor could be 4.8 times higher than that of the control group. Filtrating superiority of PC-CHFMs was becoming more prominent with the extension of operating time. In addition, the removal efficiency of NH₄⁺-N and TP in wastewater was approximately 100% at stable culture period.

Recent progress for silver nanowires conducting film for flexible electronics

Silver nanowires (AgNWs), as one-dimensional nanometallic materials, have attracted wide attention due to the excellent electrical conductivity, transparency and flexibility, especially in flexible and stretchable electronics. However, the microscopic discontinuities require AgNWs be attached to some carrier for practical applications. Relative to the preparation method, how to integrate AgNWs into the flexible matrix is particularly important. In recent years, plenty of papers have been published on the preparation of conductors based on AgNWs, including printing techniques, coating techniques, vacuum filtration techniques, template-assisted assembly techniques, electrospinning techniques and gelating techniques. The aim of this review is to discuss different assembly method of AgNW-based conducting film and their advantages.

GRAPHIC ABSTRACT

Conducting films based on silver nanowires (AgNWs) have been reviewed with a focus on their assembly and their advantages.

Facile fabrication of a conductive polypyrrole membrane for anti-fouling enhancement by electrical repulsion and in situ oxidation

Conductive membranes provide a promising method to alleviate membrane fouling, but their cost-effective fabrication, which is urgently needed, is still a challenge. This paper describes the facile fabrication of an ultrafiltration conductive polypyrrole (PPy)-modified membrane (PMM) by in situ chemical polymerization of FeCl₃ and monomer pyrrole vapor on a commercial membrane surface. The resulting membrane had a high electrical conductivity and an outstanding water flux of 2766.55 L m^-2 h^-1 bar^-1. The preparation cost of the PPy deposition was $2.22/m², which was ∼8% of the commercial ultrafiltration membrane cost. Once the PMM was charged at -1 V as a membrane electrode, the normalized water flux was maintained at 92.48 ± 1.14% after fouling by bovine serum albumin (BSA) solutions, which was 18.82% higher than that when the PMM was not charged. The reduced membrane fouling was ascribed to the electrical repulsion between the negatively charged BSA and the PMM cathode. In addition, hydroxyl and sulfate radicals were generated by peroxymonosulfate (PMS) activation on the PMM surface through electron transfer by PPy, which facilitated foulant oxidation. The PPy on the PMM surface was oxidized after catalysis and electrochemically reduced when the PMM was charged as a cathode, exhibiting continuous catalytic ability for PMS activation. These findings provide an alternative method for the facile fabrication of cost-effective conductive membranes to mitigate membrane fouling.