Significantly improved gas separation properties of sulfonated PIM-1 by direct sulfonation using SO3 solution

Constructing Hydrophilic Polymer Membranes with Microporosity for Aqueous Redox Flow Batteries

Ion selective membranes (ISMs) are key components of aqueous redox flow batteries (ARFBs), and their property in selective ion transport largely determines the energy storage efficiency of ARFBs. Traditional ISMs are based on microphase-separated structures and have been advanced for many years, but most of them show poor performance as membrane separators in ARFBs due to their conductivity-selectivity. In recent years, using confined micropores instead of dense hydrophilic regions as ion channels has been demonstrated to effectively break this tradeoff. We here summarize the synthetic strategies for constructing hydrophilic polymer membranes with microporosity and highlight the performance of some typical microporous ISMs in ARFBs. We also propose fundamental issues that remain to be addressed for the further development of ISMs.

Membranes of Polymer of Intrinsic Microporosity PIM-1 for Gas Separation: Modification Strategies and Meta-Analysis

Polymers of intrinsic microporosity (PIMs) have received considerable attention for making high-performance membranes for carbon dioxide separation over the last two decades, owing to their highly permeable porous structures. However, challenges regarding its relatively low selectivity, physical aging, and plasticisation impede relevant industrial adoptions for gas separation. To address these issues, several strategies including chain modification, post-modification, blending with other polymers, and the addition of fillers, have been developed and explored. PIM-1 is the most investigated PIMs, and hence here we review the state-of-the-arts of the modification strategies of PIM-1 critically and discuss the progress achieved for addressing the aforementioned challenges via meta-analysis. Additionally, the development of PIM-1-based thin film composite membranes is commented as well, shedding light on their potential in industrial gas separation. We hope that the review can be a timely snapshot of the relevant state-of-the-arts of PIMs guiding future design and optimisation of PIMs-based membranes for enhanced performance towards a higher technology readiness level for practical applications.

Effect of Temperature-Induced Aging on the Gas Permeation Behavior of Thin Film Composite Membranes of PIM-1 and Carboxylated PIM-1

Polymers of intrinsic microporosity (PIMs) are a class of promising gas separation materials due to their high membrane permeabilities and reasonable selectivities. When processed into thin film composite (TFC) membranes, their high gas throughput aligns closely with industrial requirements, but they are prone to physical aging and plasticization effects. TFC membranes based on the prototypical PIM-1 and its carboxylated derivative cPIM-1 exhibit temperature-dependent gas permeation behavior, which has not been extensively studied before. In single CO2 permeation tests, measurable physical aging occurred when the temperature was raised to 55 °C within a period of 90 min, and the aging rate accelerated as temperature was raised further. TFC membranes prepared from cPIM-1 exhibited a faster aging rate compared to PIM-1 at the same temperature. The decreased permeance could be at least partially recovered through a 5 day methanol vapor treatment. In mixed gas experiments, all membranes showed decreased permselectivities at elevated temperatures. The plasticization pressure of TFC membranes occurred at around 1 bar of CO2 partial pressure, independent of temperature. Significant plasticization was particularly evident for cPIM-1 TFC membranes under CO2/CH4 conditions with increasing temperature, which resulted in increased gas permeance for both components.

Penetrant-induced plasticization in microporous polymer membranes

Penetrant-induced plasticization has prevented the industrial deployment of many polymers for membrane-based gas separations. With the advent of microporous polymers, new structural design features and unprecedented property sets are now accessible under controlled laboratory conditions, but property sets can often deteriorate due to plasticization. Therefore, a critical understanding of the origins of plasticization in microporous polymers and the development of strategies to mitigate this effect are needed to advance this area of research. Herein, an integrative discussion is provided on seminal plasticization theory and gas transport models, and these theories and models are compared to an exhaustive database of plasticization characteristics of microporous polymers. Correlations between specific polymer properties and plasticization behavior are presented, including analyses of plasticization pressures from pure-gas permeation tests and mixed-gas permeation tests for pure polymers and composite films. Finally, an evaluation of common and current state-of-the-art strategies to mitigate plasticization is provided along with suggestions for future directions of fundamental and applied research on the topic.

Covalent organic frameworks with flexible side chains in hybrid PEMs enable highly efficient proton conductivity

Electrochemical hydrogen compression (EHC) is an emerging energy conversion technology. Proton exchange membranes (PEMs) with high proton conductivity and high mechanical strength are highly required to meet the practical requirements of EHC. Herein, ionic covalent organic frameworks (iCOFs) with tunable side chains were synthesized and introduced into the sulfonated poly (ether ether ketone) (SPEEK) matrix to fabricate hybrid PEMs. In our membranes, the rigid iCOFs afford ordered proton conduction channels, whereas the flexible side chains on iCOFs afford abundant proton conduction sites, adaptive hydrogen bonding networks, and high local density short hydrogen bonds for highly efficient proton transport. Moreover, the hydrogen bond interactions between the side chains on iCOFs and the SPEEK matrix enhance the mechanical stability of membranes. As a result, the hybrid PEM acquires an enhanced proton conductivity of 540.4 mS cm-1 (80 °C, 100%RH), a high mechanical strength of 120.41 MPa, and a superior performance (2.3 MPa at 30 °C, 100%RH) in EHC applications.

Spacer-Engineered Ionic Channels in Covalent Organic Framework Membranes toward Ultrafast Proton Transport

Side-chain engineering of covalent organic frameworks as advanced ion conductors is a critical issue to be explored. Herein, ionic covalent organic framework membranes (iCOFMs) with spacer-engineered ionic channel are de novo designed and prepared. The ionic channels are decorated with side chains comprising spacers having different carbon chain lengths and the -SO₃ H groups at the end. Attributed to the synergistic contribution from the spacers and the -SO₃ H groups, the iCOFM with moderate-length spacer exhibit the highest through-plane proton conductivity of 889 mS cm^-1 at 90 °C.

Preparation and gas separation performance of polyimide membranes endcapped with ionic liquid-type structures

A set of ionic liquid capped polyimide membranes was prepared using 1-aminoethyl-3-methylimidazolium hexafluorophosphate (IL1) and 1-aminopropylimidazolium bis(trifluoromethylsulfonyl)imine (IL2) as the terminal groups. The products’ molecular weights, mechanical properties, and separation permeability (CO2/CH4) were investigated. For CO2/CH4 separation, the selectivity of the ionic liquid capped polyimide membranes was higher than that of noncapped ones. Among them, the membrane synthesized by 4.4′- diaminodiphenyl ether and 4.4′-(hexafluoroisopropyl) diphthalic anhydride (6FDA) as monomer, with IL1 as terminal group, displayed the best selectivity. Its permeability was 7.47 Barrer and selectivity 102.42, which exceeded the 1991 Robeson curve. Polyimide membranes capped by ionic liquid showed high gas selectivity and good gas permeability as well as good physical and chemical properties. Consequently, it can be concluded that introducing an ionic liquid structure to polyimide chains could make attractive membrane materials for various gas separation and related applications.