Preparation of carbon nanotube/tannic acid/polyvinylpyrrolidone membranes with superwettability for highly efficient separation of crude oil-in-water emulsions

Construction of CS-SDAEM long-chain polysaccharide derivative on TA@CNTs coated PVDF membrane with effective oil-water emulsion purification and low contamination rate

Currently, the most effective way to improve the anti-fouling performance of water treatment separation membrane is to enhance the hydrophilicity of the membrane surface, but it can still cause contamination, leading to the occurrence of flux reduction. The construction of a strong hydration layer to resist wastewater contamination is still a challenging task. In this study, a defect-free hydration layer barrier was achieved by grafting chitosan polysaccharide derivatives (CS-SDAEM) on the membrane, which achieved in effective fouling prevention and low flux decline rate. A layer of tannic acid-coated carbon nanotubes (TA@CNTs) has been uniformly deposited on the commercial PVDF membrane so that the surface was rich in -COOH groups, providing sufficient reaction sites. These reactive groups facilitate the grafting of amphiphilic polymers onto the membrane. This modification strategy achieved in enhancing the antifouling performance. The modified membrane achieved low contamination rate with DR of 16.9 % for wastewater filtration, and the flux recovery rate was above 95 % with PWF of 1100 (L·m-2·h-1). The membrane had excellent anti-fouling performance, which provided a new route for the future development of water treatment membrane.

Sustainable, biocompatible, and mass-producible superwetting water caltrop shell biochars for emulsion separations

The separation of oily wastewater, specifically emulsions, is a crucial global issue. Possible strategies for the efficient separation of emulsified oil/water mixtures through sustainable and environmentally friendly materials have recently drawn considerable attention. In our study, we prepared superwetting water caltrop shell biochar (WCSB) via a top-lit-updraft carbonization procedure. The as-prepared WCSB was characterized by superhydrophilicity, underwater superoleophobicity, underoil superhydrophilicity, and underoil water adsorption ability. Because of its superwetting properties, WCSB was used for the separation of both surfactant-stabilized oil-in-water emulsions (SOIWEs) and surfactant-stabilized water-in-oil emulsions (SWIOEs) with very high fluxes (up to 74,700 and 241,000 L m^-2 h^-1 bar^-1 for SOIWE and SWIOE, respectively). The separation performances were excellent, with oil contents in all SOIWE filtrates lower than 10 ppm and oil purities in all SWIOE filtrates higher than 99.99 wt%. Moreover, WCSB was applied to separate dye-spiked emulsions. Due to their high emulsion separation ability, sustainability, good biocompatibility, and ease of mass production, the as-prepared WCSBs have notable potential for utilitarian applications.

Blending Electrostatic Spinning Fabrication of Superhydrophilic/Underwater Superoleophobic Polysulfonamide/Polyvinylpyrrolidone Nanofibrous Membranes for Efficient Oil-Water Emulsion Separation

The scarcity of water resources has led to widespread interest in the treatment of oily wastewater. This study prepared a novel superhydrophilic/underwater superoleophobic polysulfonamide (PSA)/polyvinylpyrrolidone (PVP) nanofibrous membrane through electrostatic spinning for efficient oil-water emulsion separation. The surface morphology, fiber diameter distribution, wettability properties, and oil-water emulsion separation performance of the membranes were investigated. Results showed that the addition of PVP increases the diameter of the fibers, which led to a loose, large, porous structure and improved the permeability of the membranes. A high pure-water flux of 2057 L·m^-2·h^-1 was obtained for membranes with PVP addition of 3 wt%, providing an 835% increase in pure-water flux compared with a pure PSA nanofibrous membrane (220 L·m^-2·h^-1). For n-hexane-in-water emulsions, the optimum membrane obtained a high separation efficiency of 99.7%, in which flux was 1.5 times greater than that of the pure PSA nanofibrous membrane. Moreover, the optimum membrane exhibited good recycling stability and solvent resistance. The as-prepared PSA/PVP nanofibrous membrane displayed high permeability, an outstanding rejection rate, resistance to organic solvents, and reusability for oil-water separation, providing great potential in practical membrane separation applications.

Green Preparation of a Carboxymethyl Cellulose-Coated Membrane for Highly Efficient Separation of Crude Oil-In-Water Emulsions

Developing high-performance membranes is an extremely significant strategy to combat increasing severe oil pollution. However, most of the previously reported superwettable membranes have been inevitably involved with the use of toxic solvents and complicated preparation processes. In addition, most of them lacked the capacity of separating crude oil-in-water emulsions. Herein, a facile and green strategy is employed to fabricate a polytetrafluoroethylene (PTFE) membrane with a mixed suspension of PDA@ZIF-8 and carboxymethyl cellulose (CMC) using water as a solvent via the vacuum filtration method. Combining hydrophilic property with micro-nano-roughness, the CMC-PDA@ZIF-8-coated PTFE membrane (CPZP membrane) exhibits excellent underwater superoleophobicity. More importantly, the separation efficiency of various surfactant-stabilized oil-in-water emulsions including crude oil/water emulsion is higher than 99.2% with a flux up to 1306.5 L m^-2 h^-1, and the separation performance remains nearly the same after 10 cycles. Moreover, outstanding underwater superoleophobic and self-cleaning properties are maintained after long-distance sandpaper abrasion and multiple bending tests. Meanwhile, its exceptional separation performance is still maintained in harsh environments (3.5 wt % NaCl, 1 M HCl, 60 °C hot water) even after immersing it for 24 h. Therefore, this green-prepared and high-performance membrane has tremendous application prospects in treating oily wastewater.

Tannic acid-based functional coating: surface engineering of membranes for oil-in-water emulsion separation

Recent progress in the tannic acid-based functional coating for surface engineering of membranes toward oil-in-water emulsion separation is summarized.