Mussel-inspired polyphenol/polyethyleneimine assembled membranes with highly positive charged surface for unprecedented high cation perm-selectivity

Tailoring the Performance of a Composite PEI Nanofiltration Membrane via Incorporating Activated PDA for Efficient Dye Sieving and Salt Separation

Efficient dye sieving and salt separation can facilitate the recycling of valuable resources in textile wastewater treatment. This study focuses on developing a high-performance nanofiltration membrane (NF) by co-depositing activated polydopamine (O-PDA), oxidized with KMnO4, and polyethyleneimine (PEI) onto a polysulfone support membrane (PSF), thereby enabling effective dye sieving and salt separation. Due to the high hydrophilicity of PDA and the formation of high molecular polymers after oxidation, it was anticipated that O-PDA would crosslink the PEI layer, providing rapid permeating channels. Filtration experiments demonstrated that the formation of O-PDA significantly enhanced the salt retention rate of nanofiltration membranes, achieving a nearly threefold increase in NaCl retention from 15% to 45.7%. It was observed that the retention performance of O-PDA could be adjusted by controlling its loading or oxidation level. Furthermore, despite a notable reduction in permeability, the dye removal efficiency of the O-PDA/PEI membrane increased substantially to 99.5%. Long-term filtration experiments also confirmed both the stability and anti-fouling properties of this membrane design. Clearly, owing to its excellent operational stability and anti-fouling characteristics, the O-PDA/PEI membrane exhibits great potential for applications in dye sieving and salt separation.

Transparent Superhydrophilic Coating with Robust and Persistent Anti-Oil-Fouling Properties for Efficient Long-Term Oil/Water Emulsion Separation

Porous membranes with superhydrophilicity and underwater superoleophobicity have attracted considerable attention for efficient oil/water emulsion separation. However, such membranes fail to remediate severe oil contamination in long-term applications and exhibit a serious water flux decline. Herein, a universal combination strategy integrating the high coverage of a mussel-inspired sticky interlayer and a double rigid cellulose nanofiber-amorphous calcium carbonate (CNF-ACC) composite outer layer is proposed to prepare a superhydrophilic coating surface with superior anti-oil-fouling properties on diverse substrates. The introduction of the mussel-inspired interlayer not only provides a stable and complete coverage interface but also offers an anchor to fix the outstanding hydration of the outer CNF-ACC composite layer. The high-coverage and double rigid superior hydration CNF-ACC layer provides excellent anti-oil-fouling characteristics, irrespective of the type of oil, under various conditions, such as water-prewetted or oil-fouled environments. Owing to its superior anti-oil-fouling property, the coating-modified membrane shows efficient and long-term separation of diverse oil/water emulsions without significant flux decline and with a flux recovery ratio of nearly 100%. In addition, this coating exhibits antifogging and high transparency, which may show promising applications in diverse optical devices.

Boosting lithium/magnesium separation performance of selective electrodialysis membranes regulated by enamine reaction

Monovalent cation exchange membranes (MCEMs) have progressively played an important role in the field of ion separation. However, according to transition state theory (TST), synchronously tuning the enthalpy barrier (△H) and entropy barrier (△S) for cation transport to improve ion separation performance is challenging. Here, the enamine reaction between the -NH- and -CHO groups is applied to regulate the subsequent Schiff-base reaction between the -CHO and -NH2 groups, which reduces the positive charges of the selective layer but increases the steric hindrance. The increased -T△S (△S term) for cation transport plays an important role in improving Li+/Mg2+ separation performance. The optimal positively-charged glutaraldehyde@piperazine/polyethyleneimine assembled membrane (M-Glu@PIP/PEI) has a perm-selectivity (Li+/Mg2+) of 31.83 with a Li+ flux of 1.87 mol·m-2·h-1, surpassing the Li+/Mg2+ separation performance of state-of-the-art monovalent ion selective membranes (MISMs). Most importantly, the selective electrodialysis (S-ED) process with M-Glu@PIP/PEI can be directly applied to treat simulated salt-lake brines (SLBs), and its superior Li+/Mg2+ separation performance and operational stability enables 74.44 % of the lithium resources with a Li+ purity of 34.02 % to be recovered. This study presents new insights into the design of high-performance MCEMs for energy-efficient resource recovery.

Improving multifunctional properties of the polyvinylidene fluoride (PVDF) membrane with crosslinked dialdehyde-starch (DAS) and polyethyleneimine (PEI) coating

Dialdehyde-soluble starch (DAS) and polyethyleneimine (PEI) were used to coat the polyvinylidene fluoride (PVDF) membrane for improving its antifouling and multifunctional properties through a combination of dip-coating and spray-coating techniques. The resulting membrane demonstrated excellent hydrophilicity and underwater oleophobicity due to hydrophilic DAS and PEI on its surface. The membrane achieved an impressive oil removal rate of 99.8 % and a flux 1420.8 ± 26.5 L·m-2·h-1 when it was used for oil-water emulsion separation. The hydration layer formed by the DAS and PEI greatly enhanced the membrane antifouling property, and its flux recovery rate was up to 96.6 % in BSA filtration experiments. The positive charge PEI and the negative charge DAS contributed to high separation efficiency of 99.1 % for the anion dye MO with the membrane D10P20, and high separation efficiency of 88.3 % for the cation dye RhB with the membrane P5D20. In addition, the coating layer was stable due to the cross-linked DAS and PEI. This research contributes greatly to the preparation of antifouling and multifunctional membrane using environmentally friendly material including polysaccharide derivatives and water soluble polymer.

Simultaneous Manipulation of Membrane Enthalpy and Entropy Barriers towards Superior Ion Separations

Sub-nanoporous membranes with ion selective transport functions are important for energy utilization, environmental remediation, and fundamental bioinspired engineering. Although mono/multivalent ions can be separated by monovalent ion selective membranes (MISMs), the current theory fails to inspire rapid advances in MISMs. Here, we apply transition state theory (TST) by regulating the enthalpy barrier (ΔH) and entropy barrier (ΔS) for designing next-generation monovalent cation exchange membranes (MCEMs) with great improvement in ion selective separation. Using a molecule-absorbed porous material as an interlayer to construct a denser selective layer can achieve a greater absolute value of ΔS for Li+ and Mg2+ transport, greater ΔH for Mg2+ transport and lower ΔH for Li+ transport. This recorded performance with a Li+/Mg2+ perm-selectivity of 25.50 and a Li+ flux of 1.86 mol ⋅ m-2 ⋅ h-1 surpasses the contemporary "upper bound" plot for Li+/Mg2+ separations. Most importantly, our synthesized MCEM also demonstrates excellent operational stability during the selective electrodialysis (S-ED) processes for realizing scalability in practical applications.

Construction of Fire Safe Thermoplastic Polyurethane/Reduced Graphene Oxide Hierarchical Composites with Electromagnetic Interference Shielding

Incorporating outstanding flame retardancy and electromagnetic interference shielding effectiveness (EMI SE) into polymers is a pressing requirement for practical utilization. In this study, we first employed the principles of microencapsulation and electrostatic interaction-driven self-assembly to encapsulate polyethyleneimine (PEI) molecules and Ti3C2Tx nanosheets on the surface of ammonium polyphosphate (APP), forming a double-layer-encapsulated structure of ammonium polyphosphate (APP@PEI@Ti3C2Tx). Subsequently, flame-retardant thermoplastic polyurethane (TPU) composites were fabricated by melting the flame-retardant agent with TPU. Afterwards, by using air-assisted thermocompression technology, we combined a reduced graphene oxide (rGO) film with flame-retardant TPU composites to fabricate hierarchical TPU/APP@PEI@Ti3C2Tx/rGO composites. We systematically studied the combustion behavior, flame retardancy, and smoke-suppression performance of these composite materials, as well as the flame-retardant mechanism of the expansion system. The results indicated a significant improvement in the interface interaction between APP@PEI@Ti3C2Tx and the TPU matrix. Compared to pure TPU, the TPU/10APP@PEI@1TC composite exhibited reductions of 84.1%, 43.2%, 62.4%, and 85.2% in peak heat release rate, total heat release, total smoke release, and total carbon dioxide yield, respectively. The averaged EMI SE of hierarchical TPU/5APP@PEI@1TC/rGO also reached 15.53 dB in the X-band.

Robust nanoparticles growth in the interior of porous sponges for efficient dye adsorption and emulsion separation

Emulsified oils and dye contaminants already pose a huge threat to global ecosystems and human health. It is a significant research topic to develop efficient, rapid, versatile methods for emulsion separation and dye adsorption. The membrane material modified with common methods only modified the outer surface of the membrane, while the interior is hardly fully decorated. In this investigation, a solvent exchange method was used to in situ grow nanoparticles in the interior of a porous sponge. These nanoparticles were obtained with polyethyleneimine, gallic acid, and tannic acid via Michael addition and Schiff base reaction. The prepared nanoparticle-coated sponges provided efficient separation of dyes, emulsions, and complex contaminants. The separation efficiency of the dye reached 99.49%, and the separation efficiency of the emulsion was as high as 99.87% with a flux of 11140.3 L m-2 h-1. Furthermore, the maximum adsorption capacity reached 486.8 mg g-1 for cationic dyes and 182.1 mg g-1 for anionic dyes. More importantly, the nanoparticles were highly robust on the surface of the porous sponge, and the modified sponge could have long-term applications in hazardous environments. Overall, it is envisioned that the nanoparticles-modified porous sponge exhibited considerable potential for emulsion and dye wastewater treatment.

Preparation of polyphenol-structural colored silk fabrics with bright colors

Conventional textile dyeing relies on the use of dyes and pigments, which can cause severe environmental contamination and waste a large amount of water. Structural coloring is one of the effective ways to achieve environmentally friendly coloring of textiles. In this work, three plant polyphenols with the same o-benzenetriol structure (tannic acid (TA), gallic acid (GA), and tea polyphenol (TP)) were selected as raw materials. Three plant polyphenols can quickly form nanofilms at the gas-liquid interface through a Schiff base reaction with polyethyleneimine (PEI) under mildly alkaline conditions, which were deposited to the surface of silk fabric, allowing precise control over the thickness of film by adjusting the time, resulting in various structurally colored silk fabric. This method for creating structural colors is not substrate-specific and enables the quick production of structural colors on various textile substrates. Furthermore, the structural color silk fabric based on plant polyphenol has antibacterial performance. This textile coloring method is simple, cost-effective and environmentally friendly, providing a new approach to eco-friendly textile dyeing.

Membrane Design Principles for Ion-Selective Electrodialysis: An Analysis for Li/Mg Separation

Selective electrodialysis (ED) is a promising membrane-based process to separate Li+ from Mg2+, which is the most critical step for Li extraction from brine lakes. This study theoretically compares the ED-based Li/Mg separation performance of different monovalent selective cation exchange membranes (CEMs) and nanofiltration (NF) membranes at the coupon scale using a unified mass transport model, i.e., a solution-friction model. We demonstrated that monovalent selective CEMs with a dense surface thin film like a polyamide film are more effective in enhancing the Li/Mg separation performance than those with a loose but highly charged thin film. Polyamide film-coated CEMs when used in ED have a performance similar to that of polyamide-based NF membranes when used in NF. NF membranes, when expected to replace monovalent selective CEMs in ED for Li/Mg separation, will require a thin support layer with low tortuosity and high porosity to reduce the internal concentration polarization. The coupon-scale performance analysis and comparison provide new insights into the design of composite membranes used for ED-based selective ion-ion separation.

Schiff base synergized with protonation of PEI to achieve smart antibacteria of nanocellulose packaging films

Microbial growth and reproduction can cause food spoilage. Developing the controlled release packaging films for food is an ideal solution. In this study, polyethyleneimine (PEI) was grafted to cellulose nanofibers (CNF) films by Schiff base, and when the CNF/PEI films were stimulated by pH, PEI released from the CNF/PEI films due to Schiff base hydrolysis, improving the antibacterial efficiency of PEI. Stimulated by acid with pH of 4, the PEI cumulative release rate of the CNF/PEI₈₀₀ and the CNF/PEI₂₀₀₀ films reached to 92.90 % and 87.28 %, respectively. At the same time, the amino groups of PEI protonated by obtaining H⁺, the charge density increased, and PEI molecular chains extended, enhancing the antibacterial activity of films. The Zeta potential value on the surface of the CNF/PEI film increased with the decrease of pH value. Schiff base synergized with protonation of PEI to achieve smart antibacteria of CNF packaging films. The antibacterial rates of the film against L. monocytogenes and E. coli were 94.7 % and 90.6 % at pH 4, but 29.5 % and 23.6 % at pH 8, respectively. The developed films also had good barrier properties of oxygen, visible light and mechanical properties, and had an attractive application prospect in food preservation to control release of antibacterial agent.

Cation Exchange Membranes and Process Optimizations in Electrodialysis for Selective Metal Separation: A Review

The selective separation of metal species from various sources is highly desirable in applications such as hydrometallurgy, water treatment, and energy production but also challenging. Monovalent cation exchange membranes (CEMs) show a great potential to selectively separate one metal ion over others of the same or different valences from various effluents in electrodialysis. Selectivity among metal cations is influenced by both the inherent properties of membranes and the design and operating conditions of the electrodialysis process. The research progress and recent advances in membrane development and the implication of the electrodialysis systems on counter-ion selectivity are extensively reviewed in this work, focusing on both structure-property relationships of CEM materials and influences of process conditions and mass transport characteristics of target ions. Key membrane properties, such as charge density, water uptake, and polymer morphology, and strategies for enhancing ion selectivity are discussed. The implications of the boundary layer at the membrane surface are elucidated, where differences in the mass transport of ions at interfaces can be exploited to manipulate the transport ratio of competing counter-ions. Based on the progress, possible future R&D directions are also proposed.

A charged nanocomposite membrane via co-deposition of gallic acid and polyethyleneimine-silver for improving separation and antibacterial properties

Pharmaceuticals have been continuously detected from surface water and groundwater. In order to improve the rejection performance of pharmaceuticals by a nanofiltration membrane (NF), a positively charged membrane was prepared by co-deposition of natural gallic acid and polyethyleneimine on the polyacrylonitrile hydrolysis membrane. Effects of gallic acid concentration, polyethylene imine concentration, reaction time, and the molecular weight of polyethylene imine were documented. The physical and chemical properties of the membrane were also investigated by surface morphology, hydrophilicity, surface charge, and molecular weight cut-off. The optimized membrane had a molecular weight cut-off of about 958 Da and possessed a pure water permeability of 74.21 L·m^-2·h^-1·MPa^-1. The results exhibited salt rejection in the following order: MgCl₂ > CaCl₂ > MgSO₄ > Na₂CO₃ > NaCl > Na₂SO₄, while the rejection ability of pharmaceuticals is as follows: amlodipine > atenolol > carbamazepine > ibuprofen, suggesting that the positively charged membrane has enhanced retention to both divalent cations and charged pharmaceuticals. In addition, the antibacterial membrane was obtained by loading silver nanoparticles onto the positively charged membrane, which greatly improved the antibacterial ability of the membrane.

Amine-functionalized MOF-derived carbon materials for efficient removal of Congo red dye from aqueous solutions: simulation and adsorption studies

In this study, a novel polyethyleneimine (PEI) modified MOF-derived carbon adsorbent (PEI@MDC) was proposed, which exhibited significant adsorption capacity for Congo Red (CR) in aqueous solutions. FT-IR and XPS results showed that PEI was successfully grafted onto MDC, increasing the content of amine groups on the surface of MDC. The adsorption process conformed to the Langmuir isotherm adsorption model and pseudo-second-order kinetic equation, indicating that the adsorption of CR on PEI@MDC was covered by a single layer, and the adsorption process was controlled by chemical processes. According to the Langmuir model, the maximum adsorption capacity at 30 °C was 1723.86 mg g-1. Hydrogen bonding and electrostatic interactions between CR and PEI@MDC surface functional groups were the main mechanisms controlling the adsorption process. After five adsorption-desorption cycles, PEI@MDC still showed a high adsorption capacity for CR, indicating that the adsorbent had an excellent regeneration ability.

Well-Distributed Polysilsesquioxane-Modified Carbon Nanotubes for Thermal Conductive Insulating Silicone Rubbers

Despite carbon nanotubes (CNTs) have garnered tremendous research interests for enhancing the electrical and thermal conductivity of polymers, it is still a considerable challenge to achieve the uniform dispersion of carbon nanotubes in polymer matrix. Herein, inspired by the mussel-inspired chemistry, we adopted the strategy of coating CNTs with polydopamine. And the polysilsesquioxane-modified CNTs (CNTs-PSQ) were obtained based on the click chemistry reaction. The FT-IR, Raman, XRD, and TGA collectively demonstrated the successful modification of PSQ on the surface of CNTs. The incorporation of PSQ could significantly improve the dispersion of CNTs in the silicon rubbers, and a strong interfacial interaction was formed between CNTs-PSQ and silicon rubber matrix, as observed from TEM images of silicon rubber/CNTs-PSQ nanocomposites. Meanwhile, compared with the nanocomposites with neat CNTs, the ones with CNTs-PSQ exhibited simultaneously improved electrical conductivity and insulating performance. This strategy proposed for the preparation of PSQ-modified CNTs provides insights toward highly insulating and thermal conducting polymers.