A joint experimental and theoretical study on the electronic structure and photoluminescence properties of Al2(WO4)3 powders

Porous Mullite Ceramic Modification with Nano-WO3

Mullite and mullite-alumina ceramics materials with dominance of the mullite phase are used in different areas of technology and materials science. Porous mullite ceramics materials can be used simultaneously as refractory heat insulators and also as materials for constructional elements. The purpose of this work was to investigate the WO₃ nanoparticle influence on the evolution of the aluminum tungstate and zircon crystalline phases in mullite ceramics due to stabilization effects caused by different microsize ZrO₂ and WO₃. The use of nano-WO₃ prevented the dissociation of zircon in the ceramic samples with magnesia-stabilized zirconia (MSZ), increased porosity by approximately 60 ± 1%, increased the intensity of the aluminum tungstate phase, decreased bulk density by approximately 1.32 ± 0.01 g/cm³, and increased thermal shock resistance by ensuring a loss of less than 5% of the elastic modulus after 10 cycles of thermal shock.

Enhanced Electrochemical Performance and Safety of LiNi0.88Co0.1Al0.02O2 by a Negative Thermal Expansion Material of Orthorhombic Al2(WO4)3

LiNi0.88Co0.1Al0.02O2 (NCA) is attractive for high-energy batteries, but phase transition and side reactions leave large volume change and thermal runaway. In order to address the drawbacks, orthorhombic Al2(WO4)3, a cheap anisotropic negative thermal expansion material, was synthesized and adopted to modify NCA, and its effects on the electrochemical performance and safety of NCA were investigated using multifarious techniques. Al2(WO4)3 can greatly improve the rate performance, cyclability at different temperatures, thermal stability, and interface behavior and intensify charge transfer as well as decline the deformation and side reactions of NCA. The discharge capacity of the NCA modified with 5 wt % Al2(WO4)3 reaches 170.0 mA h/g at 5.0 C and 25 °C. After 100 cycles, the values of this electrode at 1.0 C and 25 °C and at 3.0 C and 60 °C are 164.2 and 148.7 mA h/g, respectively, much higher than those of the pure NCA under the same conditions. Moreover, Al2(WO4)3 declines the byproducts and cation mixing and decreases the released heat, strain, and charge-transfer resistance after cycles of NCA about 37.1, 33.0, and 32.8%, respectively. The improvement mechanism is discussed. It opens an effective avenue for the applications of energy materials by simultaneously adjusting heat, structure, interface, and deformation.

Near-Zero Thermal Expansion in Freeze-Cast Composite Materials

Most materials expand when heated, which can lead to thermal stress and even failure. Whereas thermomiotic materials exhibit negative thermal expansion, the creation of materials with near-zero thermal expansion presents an ongoing challenge due to the need to optimize thermal and mechanical properties simultaneously. The present work describes the preparation and properties of polymer–ceramic composites with low thermal expansion. Ceramic scaffolds, prepared by freeze-casting of low-thermal-expansion Al2W3O12, were impregnated with poly(methylmethacrylate) (PMMA). The resulting composites can have a coefficient of thermal expansion as low as 2 × 10−6 K−1, and hardness values of 4.0 ± 0.3 HV/5 (39 ± 3 MPa) and 16 ± 3 HV/5 (160 ± 30 MPa) parallel and perpendicular to the ice growth, respectively. The higher hardness perpendicular to the ice growth direction indicates that the PMMA is acting to improve the mechanical properties of the composite.

Aluminum plasmonic nanoshielding in ultraviolet inactivation of bacteria

Ultraviolet (UV) irradiation is an effective bacterial inactivation technique with broad applications in environmental disinfection. However, biomedical applications are limited due to the low selectivity, undesired inactivation of beneficial bacteria and damage of healthy tissue. New approaches are needed for the protection of biological cells from UV radiation for the development of controlled treatment and improved biosensors. Aluminum plasmonics offers attractive opportunities for the control of light-matter interactions in the UV range, which have not yet been explored in microbiology. Here, we investigate the effects of aluminum nanoparticles (Al NPs) prepared by sonication of aluminum foil on the UVC inactivation of E. coli bacteria and demonstrate a new radiation protection mechanism via plasmonic nanoshielding. We observe direct interaction of the bacterial cells with Al NPs and elucidate the nanoshielding mechanism via UV plasmonic resonance and nanotailing effects. Concentration and wavelength dependence studies reveal the role and range of control parameters for regulating the radiation dosage to achieve effective UVC protection. Our results provide a step towards developing improved radiation-based bacterial treatments.

Identifying and rationalizing the morphological, structural, and optical properties of [Formula: see text]-Ag2MoO4 microcrystals, and the formation process of Ag nanoparticles on their surfaces: combining experimental data and first-principles calculations

We present a combined theoretical and experimental study on the morphological, structural, and optical properties of β-Ag2MoO4 microcrystals. β-Ag2MoO4 samples were prepared by a co-precipitation method. The nucleation and formation of Ag nanoparticles on β-Ag2MoO4 during electron beam irradiation were also analyzed as a function of electron beam dose. These events were directly monitored in real-time using in situ field emission scanning electron microscopy (FE-SEM). The thermodynamic equilibrium shape of the β-Ag2MoO4 crystals was built with low-index surfaces (001), (011), and (111) through a Wulff construction. This shape suggests that the (011) face is the dominating surface in the ideal morphology. A significant increase in the values of the surface energy for the (011) face versus those of the other surfaces was observed, which allowed us to find agreement between the experimental and theoretical morphologies. Our investigation of the different morphologies and structures of the β-Ag2MoO4 crystals provided insight into how the crystal morphology can be controlled so that the surface chemistry of β-Ag2MoO4 can be tuned for specific applications. The presence of structural disorder in the tetrahedral [MoO4] and octahedral [AgO6] clusters, the building blocks of β-Ag2MoO4, was used to explain the experimentally measured optical properties.