Thermophilic production of poly(3-hydroxybutyrate-co-3-hydrovalerate) by a mixed methane-utilizing culture

Production of poly(3-hydroxybutyrate) and poly(3-hydroxybutyrate-co-3-hydroxyvalerate) from methane and volatile fatty acids: properties, metabolic routes and current trend

Polyhydroxyalkanoates (PHAs) are biobased and biodegradable polymers that could effectively replace fossil-based and non-biodegradable plastics. However, their production is currently limited by the high production costs, mainly due to the costly carbon sources used, low productivity and quality of the materials produced. A potential solution lies in utilizing cheap and renewable carbon sources as the primary feedstock during the biological production of PHAs, paving the way for a completely sustainable and economically viable process. In this review, the opportunities and challenges related to the production of polyhydroxyalkanoates using methane and volatile fatty acids (VFAs) as substrates were explored, with a focus on poly(3-hydroxybutyrate) and poly(3-hydroxybutyrate-co-3-hydroxyvalerate). The discussion reports the current knowledge about promising Type II methanotrophs, the impact of process parameters such as limiting nutrients, CH4:O2 ratio and temperature, the type of co-substrate and its concentration. Additionally, the strategies developed until now to enhance PHA production yields were also discussed.

Exploring New Strategies for Optimizing the Production of Poly(3-hydroxybutyrate-co-3-hydroxyvalerate) from Methane and VFAs in Synthetic Cocultures and Mixed Methanotrophic Consortia

In this work, the potential of a synthetic coculture and a mixed methanotrophic consortium to synthesize poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) from renewable and waste-based feedstocks was assessed batchwise. Methylocystis parvuscocultivated with Rhodococcus opacus and a Methylocystis-enriched culture previously grown on methane were subjected to nutrient starvation in a medium enriched with valeric acid (30% w w-1 of Ctot) or with a VFAs mixture containing acetic, propionic, butyric, and valeric acids (15% w w-1 of Ctot) under a CH4:O2 or air atmosphere. For all test series, pH was adjusted to 7 after adding the cosubstrates, and a negligible substrate consumption or polymer production was considered the end point of the trial. Results showed that valeric acid promoted PHBV accumulation in both cultures regardless of the atmosphere. Interestingly, the mixture of VFAs supported PHBV accumulation only in the presence of methane. The highest PHBV contents for the coculture and the mixed consortium, equal to 73.7 ± 2.5% w w-1 and 49.6 ± 13% w w-1, respectively, were obtained with methane and the VFAs mixture. This study demonstrates the suitability of cocultures and biobased cosubstrates for the sustainable production of the biodegradable polymer PHBV.

Enrichment of mixed methanotrophic cultures producing polyhydroxyalkanoates (PHAs) from various environmental sources

Methanotrophic bacteria can use atmospheric methane (CH4) as a sole carbon source for the growth and production of polyhydroxyalkanoates (PHA). The development of CH4 bioconversion processes relies heavily on the selection of an efficient methanotrophic culture. This research assessed the effect of selected growth conditions, such as nitrogen sources on the enrichment of methanotrophic cultures from various environments for PHA accumulation. Nitrate-based medium favoured the culture growth and selection for PHA-producing methanotrophic cultures with Methylocystis sp. as a major genus and accumulation of up to 27 % polyhydroxybutyrate (PHB) in the biomass. Three PHB-producing cultures: enriched from waste activated sludge (AS), peat bog soil (PB) and landfill biocover soil (LB) were then tested for their ability to produce PHA copolymer at different CH4:O2 ratios. All enriched cultures were able to utilise valeric acid as a cosubstrate for the accumulation of PHA with a 3-hydroxyvaleric (3HV) fraction of 21-41 mol% depending on the inoculum source and CH4 concentration. The process performance of selected cultures was evaluated and compared to the culture of reference strain Methylocystis hirsuta DSM 18500. All mixed cultures irrespective of their inoculum source had similar levels of 3HV fraction in the PHA (38 ± 2 mol%). The highest poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) production was observed for AS culture at 10 % CH4 with an accumulation of 27 ± 3 % of dry cell weight (DCW), 3HV fraction of 39 ± 2 mol% and yield of 0.42 ± 0.02 g-PHA/g-substrate.

Carbon dioxide and methane as carbon source for the production of polyhydroxyalkanoates and concomitant carbon fixation

The currently used plastics are non-biodegradable, and cause greenhouse gases (GHGs) emission as they are petroleum-based. Polyhydroxyalkanoates (PHAs) are biopolymers with excellent biodegradability and biocompatibility, which can be used to replace petroleum-based plastics. A variety of microorganisms have been found to synthesize PHAs by using typical GHGs: carbon dioxide and methane as carbon sources. Converting carbon dioxide (CO2) and methane (CH4) to PHAs is an attractive option for carbon capture and biodegradable plastic production. In this review, the microorganisms capable of using CO2 and CH4 to produce PHAs were summarized. The metabolic mechanism, PHAs production process, and the factors influencing the production process are illustrated. The currently used optimization techniques to improve the yield of PHAs are discussed. The challenges and future prospects for developing economically viable PHAs production using GHGs as carbon source are identified. This work provides an insight for achieving carbon sequestration and bioplastics based circular economy.

Sustainable Process for the Production of Poly(3-hydroxybutyrate-co-3-hydroxyvalerate) from Renewable Resources: A Simulation Study

Bacterially produced polyhydroxyalkanoates are valuable substitutes for petrochemical plastics, but their current production capacities are very scarce. Producing poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHB-co-HV) from methane and odd-chain carbon fatty acids could make the production of this biodegradable polymer cost-effective. This study analyzes the main factors affecting methanotrophic growth and poly(3-hydroxybutyrate-co-3-hydroxyvalerate) accumulation, simulating a pilot-scale process based on a double-stage approach. The effects of the nitrogen source and the oxygen partial pressure during a 20 day growth phase were studied; the cosubstrate concentration, the culture selected, and the methane partial pressure were investigated during the poly(3-hydroxybutyrate-co-3-hydroxyvalerate) production stage performed within 15 days under nutrient starvation. Methylocystis parvus OBBP and Methylosinus thricosporum OB3b reached the maximum growth productivities with ammonium as the nitrogen source and oxygen at high partial pressure. The simulation of the PHB-co-HV accumulation revealed that methanotrophs could better accumulate the polymer with low valeric acid concentrations. A methane-abundant gas stream (0.5 atm of methane) could increase process yields up to 0.32 kg m^-3 d^-1.

Metabolic engineering for biosynthesis of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) from glucose and propionic acid in recombinant Escherichia coli

In this study, novel polyhydroxyalkanoate (PHA)-associated genes (phaCp and phaABp) cloned from Propylenella binzhouense L72^T were expressed in Escherichiacoli cells for PHA production, and the recombinant strains were used to analyze PHA yields with various substrates. The highest poly (3-hydroxybutyrate-co-3-hydroxy-valerate) (PHBV) yield (1.06 g/L) and cell dry weight (3.31 g/L) in E. coli DH5α/ΔptsG-CpABp were achieved by using glucose and propionicacid as substrates. Structural verification of PHBV produced by E. coli DH5α/ΔptsG-CpABp was performed to evaluate the characteristics of the polymers using Fourier transform infrared spectroscopy and nuclear magnetic resonance analysis. In addition, the X-ray diffraction results showed improved crystallinity of PHBV, and thermogravimetric analysis showed good thermal stability of 298 °C. The above findings indicated that the expression of phaCp and phaABp genes resulted in improved PHBV synthesis activity, and the polymer had better performance at higher processing temperatures.

Strategies for Biosynthesis of C1 Gas-derived Polyhydroxyalkanoates: A review

Biosynthesis of polyhydroxyalkanoates (PHAs) from C1 gases is highly desirable in solving problems such as climate change and microplastic pollution. PHAs are biopolymers synthesized in microbial cells and can be used as alternatives to petroleum-based plastics because of their biodegradability. Because 50% of the cost of PHA production is due to organic carbon sources and salts, the utilization of costless C1 gases as carbon sources is expected to be a promising approach for PHA production. In this review, strategies for PHA production using C1 gases through fermentation and metabolic engineering are discussed. In particular, autotrophs, acetogens, and methanotrophs are strains that can produce PHA from CO₂, CO, and CH₄. In addition, integrated bioprocesses for the efficient utilization of C1 gases are introduced. Biorefinery processes from C1 gas into bioplastics are prospective strategies with promising potential and feasibility to alleviate environmental issues.

A review on production of polyhydroxyalkanoate (PHA) biopolyesters by thermophilic microbes using waste feedstocks

Polyhydroxyalkanoates (PHAs) are produced by numerous microbes as a subcellular energy source. Despite of their diverse applications, exorbitant production cost limits their commercial synthesis. Apart from various cost determining factors such as cost-effective feedstocks or economic recovery methods, the use of appropriate bacteria holds the key to reduce the fermentation economics. Extremophiles, especially thermophilic PHA producers, could make the bioprocess economically viable by reducing the production cost in several aspects. Using variety of waste feedstocks as carbon substrates could open the way for the valorisation of industrial waste streams and cost-effective PHA production. Therefore, the article critically reviews the current knowledge of the synthesis of PHA polyesters in thermophilic conditions. Additionally, it summarises several studies on thermophilic PHA producing bacteria grown on various waste substrates. To conclude, the paper focuses on screening and recovery methods as well as technical challenges in thermophilic PHA production.

Recent trends in methane to bioproduct conversion by methanotrophs

Methane is an abundant and low-cost gas with high global warming potential and its use as a feedstock can help mitigate climate change. Variety of valuable products can be produced from methane by methanotrophs in gas fermentation processes. By using methane as a sole carbon source, methanotrophic bacteria can produce bioplastics, biofuels, feed additives, ectoine and variety of other high-value chemical compounds. A lot of studies have been conducted through the years for natural methanotrophs and engineered strains as well as methanotrophic consortia. These have focused on increasing yields of native products as well as proof of concept for the synthesis of new range of chemicals by metabolic engineering. This review shows trends in the research on key methanotrophic bioproducts since 2015. Despite certain limitations of the known production strategies that makes commercialization of methane-based products challenging, there is currently much attention placed on the promising further development.

Insights into enhanced polyhydroxyalkanoate production by the synergistic use of waste wood hydrolysate and volatile fatty acids by mixed microbial cultures

The feasibility of producing polyhydroxyalkanoate (PHA) from pretreated waste wood hydrolysate and volatile fatty acids (VFAs) from sewage fermented products as co-substrate feedstock through mixed microbial cultures (MMCs) process was explored. The results showed that the addition of co-substrate shortened the cycle of PHA reaching the maximum and increased the proportion of 3-hydroxyvalerate (3HV) monomer. Compared with N-excess supply, almost 1.6 times increased PHA accumulation was realized under N-limitation, and simultaneously the highest proportion of 3HV monomer with 51% was also obtained. Additionally, PHA production in S1400 reactor reached a maximum value of about 3088 mg COD/L with culture time to 36 h. The microbial community also displayed a high diversity, which was composed of 65 bacterial genera. It is a novel attempt to accumulate PHA from pretreated waste wood hydrolysate and VFAs co-substrate through MMCs, providing an effective green approach to reduce its expensive cost and achieve mass production.

Metabolic engineering of Methylorubrum extorquens AM1 for poly (3-hydroxybutyrate-co-3-hydroxyvalerate) production using formate

Formate is a promising environmentally friendly and sustainable feedstock synthesized from syngas or carbon dioxide. Methylorubrum extorquens is a type II methylotroph that can use formate as a carbon source. It accumulates polyhydroxyalkanoates (PHAs) inside the cell, mainly producing poly-3-hydroxybutyrate (PHB), a degradable biopolymer. Owing to its high melting point and stiff nature, however, mechanical property improvement is warranted in the form of copolymerization. To produce the PHA copolymer, poly (3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV), the endogenous gene phaC was deleted and the pathway genes bktB, phaJ1, and phaC2, with broader substrate specificities, were heterologously expressed. To improve the incorporation of 3-hydroxyvalerate (3HV), the expression level of bktB was improved by untranslated region (UTR) engineering, and the endogenous gene phaA was deleted. The engineered M. extorquens produced PHBV with 8.9% 3HV using formate as the sole carbon source. In addition, when propionate and butyrate were supplemented, PHBVs with 3HV portions of up to 70.6% were produced. This study shows that a PHBV copolymer with a high proportion of 3HV can be synthesized using formate, a C1 carbon source, through metabolic engineering and supplementation with short-chain fatty acids.

Poly(3-hydroxybutyrate-3-hydroxyvalerate) production from pretreated waste lignocellulosic hydrolysates and acetate co-substrate

The purpose of this study was to explore the potential of producing Poly(3-hydroxybutyrate-3-hydroxyvalerate) (PHBV) by mixed microbial culture (MMC) with lignocellulosic hydrolysates and acetate co-substrate as feedstock. The addition of co-substrate acetate led to the introduction of HV monomer into the polyhydroxyalkanoate (PHA), and the initial mixed sludge suspension (MLSS) increased with the increase of acetate. Almost 1.91-fold increase in the yield of PHA was achieved with limited nitrogen medium (the carbon to nitrogen ratio (C/N) was 33) compared to the normal nitrogen medium (C/N = 20). Limiting nitrogen source and micro alkaline culture environment was more conducive to the accumulation of PHBV. PHA production achieved to the highest value of about 2308.45 mg/L under the condition of optimized technology. Acidovorax was the dominant genus of all bioreactors using co-substrate. Further, utilizing lignocellulosic hydrolysate and acetate co-substrate as feedstock in mixed microbial culture was a promising approach in a low-cost large-scale PHA production.

Enhanced production of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) biopolymer by recombinant Bacillus megaterium in fed-batch bioreactors

Polyhydroxyalkanoates (PHAs) are biodegradable polyesters accumulated in a wide variety of microorganisms as intracellular carbon and energy storage compounds. Poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) is one of the most valuable biopolymers because of its superior mechanical properties. Here, we developed a bioprocess utilizing recombinant Bacillus megaterium strain for PHBV over-production from glucose, without any precursor addition. PHA production was performed in a controlled bioreactor by batch and fed-batch modes using wild-type B. megaterium and rec-B. megaterium cells overexpressing the native phaC gene. The effect of oxygen transfer rate on biomass formation and PHA accumulation was also investigated, under different dissolved oxygen levels. Structural and thermal properties of PHA were characterized by GC-FID, ¹H-NMR, TGA and DSC analyses. Significantly, the copolymer produced from glucose as the carbon source in rec-B. megaterium was composed of 58 mol% of 3-hydroxyvalerate monomers. After 66 h, rec-B. megaterium cells in fed-batch fermentation with a pre-determined growth rate µ₀ = 0.1 h^-1 produced the highest CDW (7.7 g L^-1) and PHA concentration (6.1 g L^-1). Moreover, an exponential glucose feeding profile resulted in 2.2-fold increase in PHA yield compared to batch cultivation. Overall, this study paves the way to an enhanced biopolymer production process in B. megaterium cells, where the highest product yield on cell was obtained as Y_P/X = 0.8 g g^-1.

The effect of methane and odd-chain fatty acids on 3-hydroxybutyrate (3HB) and 3-hydroxyvalerate (3HV) synthesis by a Methylosinus-dominated mixed culture

A methanotrophic community was enriched in a semi-continuous reactor under non-aseptic conditions with methane and ammonia as carbon and nitrogen source. After a year of operation, Methylosinus sp., accounted for 80% relative abundance of the total sequences identified from potential polyhydroxyalkanoates (PHAs) producers, dominated the methane-fed enrichment. Prior to induction of PHA accumulation, cells harvested from the parent reactor contained low level of PHA at 4.0 ± 0.3 wt%. The cells were later incubated in the absence of ammonia with various combinations of methane, propionic acid, and valeric acid to induce biosynthesis of poly(3-hydroxybutyrate) (PHB) and poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV). Previous studies reported that methanotrophic utilization of odd-chain fatty acids for the production of PHAs requires reducing power from methane oxidation. However, our findings demonstrated that the PHB-containing methanotrophic enrichment does not require methane availability to generate 3-hydroxybutyrate (3HB) and 3-hydroxyvalerate (3HV)—when odd-chain fatty acids are presented. The enrichment yielded up to 14 wt% PHA with various mole fractions of 3HV monomer depending on the availability of methane and odd-fatty acids. Overall, the addition of valeric acid resulted in a higher PHA content and a higher 3HV fraction. The highest 3HV fraction (up to 65 mol%) was obtained from the methane–valeric acid experiment, which is higher than those previously reported for PHA-producing methanotrophic mixed microbial cultures.