Relevant factors for the eco-design of polylactide/sisal biocomposites to control biodegradation in soil in an end-of-life scenario

Comparative Evaluation of Sisal and Polypropylene Fiber Reinforced Concrete Properties

This paper presents a focused comparative case study considering the influence of natural and synthetic fibers on the fresh and mechanical properties of concrete. Locally sourced 19 mm long sisal fibers from sisalana leaves and manufactured polypropylene fibers were incorporated in a normal strength concrete matrix with fiber volumetric contents of 1%. After describing the measured aggregate characteristics, mix designs, and fresh concrete properties, several destructive and non-destructive tests on hardened concrete were undertaken. The former included compression tests on cylinders and flexural tests on prismatic samples, and the latter included ultrasonic pulse velocity and rebound number tests. The workability of sisal-fiber reinforced concrete was generally lower than the nominal concrete and that provided with polypropylene fibers by about 20%, largely due to the hydrophilic nature of the natural fibers. Test results showed that the presence of sisal fibers can improve the compressive strength by about 6%, and the tensile strength by about 4%, compared with the non-reinforced counterpart. This was due to the sisal fibers storing moisture that was released gradually during hydration, helping with the strength development. The concrete with polypropylene had virtually identical properties to the reference concrete. In addition to fresh and mechanical properties, environmental impacts associated with the production of fiber and concrete were also identified and discussed. Based on the assessments from this paper, overall, from the two fibers investigated, the sisal fiber showed more promising results, indicating that natural fibers can be a more sustainable alternative to plastic fibers, providing a good balance between workability and strengths.

Fully Biobased Reactive Extrusion of Biocomposites Based on PLA Blends and Hazelnut Shell Powders (HSP)

The production of biocomposites based on natural fiber waste and biopolymers is constantly increasing because of their renewability, biodegradability, and the accordance with the circular economy principles. The aim of this work is to contrast the disadvantages in the production of biocomposites, such as reduction of molecular weight through the use of biobased chain extenders. For this purpose, epoxidized soybean oil (ESO) and dicarboxylic acids (DCAs) were used to contrast the slight chain scission observed in a poly(lactic acid) (PLA)/poly(butylene succinate-co-adipate) (PBSA) binary blend caused by the melt mixing with hazelnut shell powder (HSP). Two different dimensions of HSPs were considered in this study as well as different concentrations of the ESO/DCA system, comparing succinic acid and malic acid as dicarboxylic acids. Melt viscosity parameters, such as torque and melt volume rate (MVR), were measured to investigate the chain extender effect during the extrusion. In addition, the reactivity of the ESO/DCA system was investigated through infrared spectroscopy. The effect of chain extenders on thermal properties, in particular on the crystallinity of PLA, and on mechanical properties of final biocomposites was investigated to understand their potentialities in industrial application. Results of this study evidenced a modest increase in melt viscosity due to ESO/malic acid chain extension system, but only for the HSP with the lower dimension (so the higher surface area) and adding 0.5 wt.% of ESO/malic acid. Thus, the slight chain scission of polyesters, not significantly affecting the final properties of these biocomposites, is the most relevant effect that was revealed in this complex reactive system.

Starch-based isocyanate- and non-isocyanate polyurethane hybrids: A review on synthesis, performance and biodegradation

The challenges related to the persistence of plastics in natural ecosystems fostered strong interest in developing biodegradable bioplastics. Among natural biopolymers, starch gained both academic and industrial interest owing to its impressive physicochemical properties. The use of starch in production of polyurethane (PU) composites not only yields PUs with outstanding mechanical properties but also makes the final PU products biodegradable. The hydrophilic nature of starch limits its dispersion in hydrophobic PU polymers, although it is a significant benefit in creating starch-embedded non-isocyanate polyurethane (NIPU) composites. We present a comprehensive overview to highlight important strategies that are used to improve the compatibility of starch with various PU matrices. This review also gives an overview of the recent advances in the synthesis of starch-NIPU hybrids. Moreover, we aim to deliver critical insight into strategies that boost the biodegradation characteristics of PUs along with a discussion on various methods to assess their biodegradation.

Synthetic Biopolymers and Their Composites: Advantages and Limitations-An Overview

Recently, polymer science and engineering research has shifted toward the development of environmentally benign polymers to reduce the impact of plastic leakage on the ecosystems. Stringent regulations and concerns regarding conventional polymers are the main driving forces for the development of renewable, biodegradable, sustainable, and environmentally benign materials. Although biopolymers can alleviate plastic-related pollution, several factors dictate the utilization of biopolymers. Herein, an overview of the potential and limitations of synthetic biopolymers and their composites in the context of environmentally benign materials for a sustainable future are presented. The synthetic biopolymer market, technical advancements for different applications, lifecycle analysis, and biodegradability are covered. The current trends, challenges, and opportunities for bioplastic recycling are also discussed. In summary, this review is expected to provide guidelines for future development related to synthetic biopolymer-based sustainable polymeric materials suitable for various applications.

Effect of Cellulose and Cellulose Nanocrystal Contents on the Biodegradation, under Composting Conditions, of Hierarchical PLA Biocomposites

In this work, the effect of microfibrillated cellulose (MFC) and cellulose nanocrystals (CNCs) on the biodegradation, under composting conditions, of hierarchical PLA biocomposites (HBCs) was studied using a full 2² factorial experimental design. The HBCs were prepared by extrusion processing and were composted for 180 days. At certain time intervals, the specimens were removed from the compost for their chemical, thermal and morphological characterizations. An ANOVA analysis was carried out at different composting times to study MFC and CNCs’ effects on biodegradation. The specimen’s mass loss and molecular weight loss were selected as independent variables. The results show that the presence of MFC enhances the PLA biodegradation, while with CNCs it decreases. However, when both cellulosic fibers are present, a synergistic effect was evident—i.e., in the presence of the MFC, the inclusion of the CNCs accelerates the HBCs biodegradation. Analysis of the ANOVA results confirms the relevance of the synergistic role between both cellulosic fibers over the HBC biodegradation under composting conditions. The results also suggest that during the first 90 days of incubation, the hydrolytic PLA degradation prevails, whereas, beyond that, the enzymatic microbial biodegradation dominates. The SEM results show MFC’s presence enhances the surface biodeterioration to a greater extent than the CNCs and that their simultaneous presence enhances PLA biodegradation. The SEM results also indicate that the biodegradation process begins from hydrophilic cellulosic fibers and promotes PLA biodegradation.

Chemical Recycling of End-of-Life Poly(lactide) via Zinc-Catalyzed Depolymerization and Polymerization

The chemical recycling of poly(lactide) was investigated based on depolymerization and polymerization processes. Using methanol as depolymerization reagent and zinc salts as catalyst, poly(lactide) was depolymerized to methyl lactate applying microwave heating. An excellent performance was observed for zinc(II) acetate with turnover frequencies of up to 45000 h-1. In a second step the monomer methyl lactate was converted to (pre)poly(lactide) in the presence of catalytic amounts of zinc salts. Here zinc(II) triflate revealed excellent performance for the polymerization process (yield: 91 %, Mn ∼8970 g/mol). Moreover, the (pre)poly(lactide) was depolymerized to lactide, the industrial relevant molecule for accessing high molecular weight poly(lactide), using zinc(II) acetate as catalyst.

Ruthenium-Catalyzed Hydrogenative Degradation of End-of-Life Poly(lactide) to Produce 1,2-Propanediol as Platform Chemical

The chemical recycling of end-of-life polymers can add some value to a future circular economy. In this regard, the hydrogenative degradation of end-of-life PLA was investigated to produce 1,2-propanediol as product, which is a useful building block in polymer chemistry. In more detail, the commercially available Ru-MACHO-BH complex was applied as catalyst to degrade end-of-life PLA efficiently to 1,2-propanediol under mild conditions. After investigations of the reaction conditions a set of end-of-life PLA goods were subjected to degradation.

Tin(ii) 2-ethylhexanoate catalysed methanolysis of end-of-life poly(lactide)

The depolymerisation of end-of-life poly(lactide) (PLA) goods was studied as part of the chemical recycling of PLA.

Polycaprolactone/gelatin-based scaffolds with tailored performance: in vitro and in vivo validation

Nanofibrous scaffolds composed of polycaprolactone (PCL) and gelatin (Ge) were obtained through a hydrolytic assisted electrospinning process. The PCL-to-Ge proportion (100/0 to 20/80), as well as the dissolution time (24, 48, 72, 96, 120 h) into a 1:1 formic/acetic acid solvent before electrospinning were modified to obtain the different samples. A strong influence of these factors on the physicochemical properties of the scaffolds was observed. Higher Ge percentage reduced crystallinity, allowed a uniform morphology and increased water contact angle. The increase in the dissolution time considerably reduced the molar mass and, subsequently, fibre diameter and crystallinity were affected. During in vitro biocompatibility tests, higher cell adhesion and proliferation were found for the 60/40, 50/50 and 40/60 PCL/Ge compositions that was corroborated by MTT assay, fluorescence and microscopy. A weakened structure, more labile to the in vitro degradation in physiologic conditions was found for these compositions with higher dissolution times (72 and 96 h). Particularly, the 40/60 PCL/Ge scaffolds revealed an interesting progressive degradation behaviour as a function of the dissolution time. Moreover, these scaffolds were non-inflammatory, as revealed by the pyrogen test and after the 15-day subcutaneous in vivo implantation in mice. Finally, a reduction of the scar tissue area after infarction was found for the 40/60 PCL/Ge scaffolds electrospun after 72 h implanted in rat hearts. These results are especially interesting and represent a feasible way to avoid undesired inflammatory reactions during the scaffold assimilation.

Performance of Polyester-Based Electrospun Scaffolds under In Vitro Hydrolytic Conditions: From Short-Term to Long-Term Applications

The evaluation of the performance of polyesters under in vitro physiologic conditions is essential to design scaffolds with an adequate lifespan for a given application. In this line, the degradation-durability patterns of poly(lactide-co-glycolide) (PLGA), polydioxanone (PDO), polycaprolactone (PCL) and polyhydroxybutyrate (PHB) scaffolds were monitored and compared giving, as a result, a basis for the specific design of scaffolds from short-term to long-term applications. For this purpose, they were immersed in ultra-pure water and phosphate buffer solution (PBS) at 37 °C. The scaffolds for short-time applications were PLGA and PDO, in which the molar mass diminished down to 20% in a 20-30 days lifespan. While PDO developed crystallinity that prevented the geometry of the fibres, those of PLGA coalesced and collapsed. The scaffolds for long-term applications were PCL and PHB, in which the molar mass followed a progressive decrease, reaching values of 10% for PCL and almost 50% for PHB after 650 days of immersion. This resistant pattern was mainly ascribed to the stability of the crystalline domains of the fibres, in which the diameters remained almost unaffected. From the perspective of an adequate balance between the durability and degradation, this study may serve technologists as a reference point to design polyester-based scaffolds for biomedical applications.