Crystallization kinetics of some new olefinic block copolymers

Effect of Octene Block Copolymer (OBC) and High-Density Polyethylene (HDPE) on Crystalline Morphology, Structure and Mechanical Properties of Octene Random Copolymer

Blending octene random copolymer (ORC) with other polymers is a promising approach to improving ORC mechanical properties, such as tensile strength and elongation. In this study, octene block copolymer (OBC) with lower density than ORC and high-density polyethylene (HDPE) were used to blend with ORC. The effect of both OBC and HDPE on ORC was analyzed using scanning electron microscopy (SEM), differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA) and small-angle X-ray scattering (SAXS). For ORC/OBC blends, a small amount of OBC can improve the crystallization ability of ORC. Meanwhile, for ORC/HDPE blends, the crystallization ability of ORC was significantly suppressed, attributed to good compatibility between ORC and HDPE as indicated by the homogeneous morphology and the disappearance of the α transition peak of ORC in ORC/HDPE blends. Therefore, the tensile strength and elongation of ORC/HDPE blends are significantly higher than those of ORC/OBC blends. For ORC/OBC/HDPE ternary blends, we found that when ORC:OBC:HDPE are at a ratio of 70:15:15, cocrystallization is achieved. Although HDPE improves the compatibility of ORC and OBC, the three-phase structure of the ternary blends can be observed through SAXS when HDPE and OBC exceed 30 wt%. Blending HDPE and OBC (≤30 wt%) could improve the mechanical property of ORC.

The Influence of DMDBS on Crystallization Behavior and Crystalline Morphology of Weakly-Phase-Separated Olefin Block Copolymer

Olefin block copolymer (OBC), with its low hard segments, can form unique space-filling spherulites other than confined-crystallization morphologies, mainly due to its weak phase-separation. In this work, 1,3;2,4-Bis(3,4-dimethylbenzylidene) sorbitol (DMDBS), a well-known nucleating agent, was used to tailor the crystallization behavior and crystalline morphology of OBC. It was found that DMDBS can precipitate within an OBC matrix and self-assemble into crystalline fibrils when cooling from the melt. A non-isothermal crystallization process exhibited an increased crystallization rate and strong composition dependence. During the isothermal crystallization process, DMDBS showed a more obvious nucleating efficiency at a higher crystallization temperature. OBC showed typical spherulites when DMDBS was added. Moreover, a low addition of DMDBS significantly decreased the crystal size, while a large addition of DMDBS induced aggregates, due to the limited miscibility of DMDBS with OBC. The efficient nucleating effect of DMDBS on OBC led to an increased optical transparency for OBC/DMDBS composites.

Olefinic Thermoplastic Elastomer Gels: Combining Polymer Crystallization and Microphase Separation in a Selective Solvent

Since selectively swollen thermoplastic elastomer gels (TPEGs) afford a wide range of beneficial properties that open new doors to developing elastomer-based technologies, we examine the unique structure-property behavior of TPEGs composed of olefinic block copolymers (OBCs) in this study. Unlike their styrenic counterparts typically possessing two chemically different blocks, this class of multiblock copolymers consists of linear polyethylene hard blocks and poly(ethylene-co-α-octene) soft blocks, in which case, microphase separation between the hard and the soft blocks is accompanied by crystallization of the hard blocks. Here, we prepare olefinic TPEGs (OTPEGs) through the incorporation of a primarily aliphatic oil that selectively swells the soft block and investigate the resultant morphological features through the use of polarized light microscopy and small-/wide-angle X-ray scattering. These features are correlated with thermal and mechanical property measurements from calorimetry, rheology, and extensiometry to elucidate the roles of crystallization and self-assembly on gel characteristics and establish useful structure-property relationships.

Tuning the crystalline and mesophase structure of olefin block copolymer through self-nucleation and annealing treatments

As a type of novel semi-crystalline block copolymers, the final properties of olefin block copolymers (OBCs) greatly depend on the crystalline and phase-separated structures. In the present work, we systematically investigated the influence of self-nucleation and annealing on the lamellar and mesophase-separated structure of OBCs. According to the crystalline and melting behavior after self-nucleation and annealing treatments, four different regimes can be recognized with the self-seeding temperature Ts varying from 125 to 109 °C. In regime A, only self-nucleation occurs, while it coexists with lamellar thickening in regime B. In regime C, there is only lamellar thickening behavior. The lamellar thickening induced inconsecutive lamellar crystals observed revealed that the rearrangement of the hard blocks, which are next to the soft blocks and trapped in the intermediate regime between crystalline and amorphous phases, into neighboring lamellar crystals should be the mechanism for the lamellar thickening of the OBCs. Surprisingly, no lamellar thickening occurs and a new small melting peak appears at lower temperatures in regime D. Considering the block dispersity of OBCs, the emergence of a small melting peak at lower temperatures can be attributed to the crystallization of the ethylene sequence with relatively weaker crystallization abilities, which are not able to crystallize in a standard crystalline state. Based on these findings, we gained some new understandings on lamellar thickening behavior of OBCs and established the self-nucleation and annealing process as a powerful tool for tuning the crystalline and phase-separated structures of OBCs.

Formation of banded spherulites and the temperature dependence of the band space in olefin block copolymer

The banded spherulites for olefin block copolymer result from continuous lamellar twisting with an intriguing temperature tendency of the band space.

An extremely uniform dispersion of MWCNTs in olefin block copolymers significantly enhances electrical and mechanical performances

A new guidance for the development of conductive elastomers with improved comprehensive performance by considering chain architecture is provided.

The effect of hard block content on the orientation and mechanical properties of olefin block copolymer films as obtained via melt stretching

In this study, the orientation, structure and mechanical performance of a series of uniaxially oriented films based on olefin block copolymers (OBC) have been investigated in terms of the differences in hard block content and draw ratio (DR).

Liquid–solid transition in mesophase separated olefin multiblock copolymers during crystallization

A delayed liquid–solid transition has been found in strongly segregated olefin multiblock copolymers, compared to that in weakly segregated systems.

Effect of melting temperature on interfacial interaction and mechanical properties of polypropylene (PP) fiber reinforced olefin block copolymers (OBCs)

Transcrystalline structures for the first time were observed at the interface of OBC/PP fiber, proving that the partially melted (170 °C) and totally melted (190 °C) PP fibers have stronger interactions with OBC than unmelted PP fibers does.

Hierarchical structures of olefinic blocky copolymer/montmorillonite nanocomposites with collapsed and intercalated clay layers

Hierarchical structures of two types of nanocomposite at different scales were characterized by various techniques.