Incorporation of modified Stöber silica nanoparticles in polystyrene/polyamide-6 blends: Coalescence inhibition and modification of the thermal degradation via controlled dispersion at the interface

Implementing Silica Nanoparticles in the Study of the Airborne Transmission of SARS-CoV-2

Aerosol transmission constitutes one of the major transmission routes of the SARS-CoV-2 pathogen. Due to the pathogen's properties, research on its airborne transmission has some limitations. This paper focuses on silica nanoparticles (SiO2) of 40 and 200 nm sizes as the physicochemical markers of a single SARS-CoV-2 particle enabling experiments on the transmission of bioaerosols in public spaces. Mixtures of a determined silica concentration were sprayed on as an aerosol, whose particles, sedimented on dedicated matrices, were examined by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Since it was not possible to quantitatively identify the markers based on the obtained images, the filters exposed with the AirSampler aspirator were analyzed based on inductively coupled plasma optical emission spectroscopy (ICP-OES). The ICP-OES method enabled us to determine the concentration of silica after extracting the marker from the filter, and consequently to estimate the number of markers. The developed procedure opens up the possibility of the quantitative estimation of the spread of the coronavirus, for example in studies on the aerosol transmission of the pathogen in an open environment where biological markers-surrogates included-cannot be used.

Interfacially compatibilized PI/PDMS blends with reduced octadecylamine-functionalized graphene oxide: morphological and rheological properties

We investigate the interfacial compatibilization effect of reduced octadecylamine-functionalized graphene oxide (ODA-GO) on the morphological and rheological properties of immiscible homopolymer blends of polydimethylsiloxane (PDMS) and polyisoprene (PI). We prepared droplet-matrix blends with a PI : PDMS ratio of 30 : 70 or 70 : 30 and interfacially localized ODA-GO stabilizer loadings from 0.1% to 1%. Blends were examined by optical microscopy and rheometry. Both blends show typical droplet-matrix morphology with stabilized round drops that do not stick together. With the addition of ODA-GO, smaller drops were observed in PI-continuous blends as compared to the PDMS-continuous blends suggesting that the effects of particles are not symmetric in the two cases. At sufficiently high ODA-GO loadings, flow-induced coalescence is suppressed almost completely. Dynamic oscillatory rheology broadly confirms the morphological observations. Specifically, all the blends show an interfacial relaxation process that is distinct from the bulk viscoelasticity, and the dependence of this process on GO content and flow conditions confirms the compatibilizing effect of the ODA-GO. This work provides a strategy for interfacially-compatibilizated polymer blends with specific properties for practical applications.

Recent advances in chemical surface modification of metal oxide nanoparticles with silane coupling agents: A review

Nowadays, metal oxide nanoparticles (NPs) have been applied in various fields of nanotechnology including catalysis of chemical reactions, drug delivery, water treatment, textile industries, polymer composites, adhesives, and coatings. The greatest challenge in relation to metal oxide NPs is high tendency to aggregation. Chemical surface modification of metal oxide NPs has gained widely interest to control of dispersion and aggregation of NPs. Silane modifiers are one of the most important bifunctional modifiers that are frequently used for surface treatment of metal oxide NPs. In this review paper, we first focus on the synthesis, surface thermodynamic properties, surface modification techniques, and kinetic of silanization reaction of metal oxide NPs. Then, the recent development in using silane modifiers for treatment of metal oxide NPs in various applications were investigated. It was found that the unmodified NPs have high surface energy and are thermodynamically unstable. The thermodynamic properties of NPs including G_m^s, H_m^s, and S_m^sincrease with decreasing the particle size. Aggregation phenomena is the simple way to reduce the excess surface energy of NPs that leads to an increase in particle size. Therefore, the chemical surface modification of NPs using silane modifiers can be used as an effective method for the prevention of NPs agglomeration and improvement of NPs stability.

Development of an Immiscible Polymer/Polymer/Nanoparticle System to Assess the Location of Nanoparticles by Quantitative Optical Microscopy

The thermo-optical behavior of immiscible PS/PC blends filled with silica nanoparticles was studied in order to get some information upon the location of nanoparticles in the polymer blend phases and interface using optical microscopy. The systems were designed taking into account rheological and optical requirements, having droplet-matrix morphology, with particle size in the range of the visible light wavelength. The melt blending procedure helped to set the nanoparticles at specific locations including within the PC minor phase, PS matrix phase and PS/PC interphase, which was confirmed via transmission electron microscopy. The light scattering was measured via the normalized transmitted light intensity over temperature, encompassing the Tg of the two polymers. The PS/PC blends showed an increase in the light scattering as compared to the pure polymers, which is magnified upon increasing the PC content. The addition of the nanosilica forming PS/PC/Nanosilica systems greatly reduces the light scattering, particularly above the Tg of the PS phase. The use of hydrophilic nanosilica does not show any appreciable hysteresis upon comparing data from heating and cooling cycles. This type of silica stays mainly trapped within the PC dispersed phase, little interfering with the light scattering, which happens at the polymer-polymer interface. On the other hand, the use of hydrophobic nanosilica does show a clear hysteresis. The hydrophobic silica located at the PS/PC interphase, interfere with the light scattering intensity at this interface, and can be used to identify its presence. The proposed procedure can help control the mixing process, thus improving the effective action of the nanoparticles in the final properties of polymer systems.

Influence of Nanomaterial Compatibilization Strategies on Polyamide Nanocomposites Properties and Nanomaterial Release during the Use Phase

The incorporation of small amounts of nanofillers in polymeric matrices has enabled new applications in several industrial sectors. The nanofiller dispersion can be improved by modifying the nanomaterial (NM) surface or predispersing the NMs to enhance compatibility. This study evaluates the effect of these compatibilization strategies on migration/release of the nanofiller and transformation of polyamide-6 (PA6), a thermoplastic polymer widely used in industry during simulated outdoors use. Two nanocomposites (NCs) containing SiO2 nanoparticles (NPs) with different surface properties and two multiwalled carbon nanotube (MWCNT) NCs obtained by different addition methods were produced and characterized, before and after accelerated wet aging conditions. Octyl-modified SiO2 NPs, though initially more aggregated than uncoated SiO2 NPs, reduced PA6 hydrolysis and, consequently, NM release. Although no clear differences in dispersion were observed between the two types of MWCNT NCs (masterbatch vs direct addition) after manufacture, the use of the MWCNT masterbatch reduced PA6 degradation during aging, preventing MWCNT accumulation on the surface and further release or potential exposure by direct contact. The amounts of NM released were lower for MWCNTs (36 and 108 mg/m(2)) than for SiO2 NPs (167 and 730 mg/m(2)), being lower in those samples where the NC was designed to improve the nanofiller-matrix interaction. Hence, this study shows that optimal compatibilization between NM and matrix can improve NC performance, reducing polymer degradation and exposure and/or release of the nanofiller.