Phase behavior of the polymer/drug system PLA/DEET

3D-printing of the polymer/insect-repellent system poly(l-lactic acid)/ethyl butylacetylaminopropionate (PLLA/IR3535)

The polymer/solvent system poly(l-lactic acid)/ethyl butylacetylaminopropionate (PLLA/IR3535) is regarded as an insect-repellent-delivery system, serving, e.g., for fighting mosquito-borne tropical diseases. In such systems the solid polymer hosts the liquid repellent, with the latter slowly released to the environment, expelling mosquitoes. As a new approach, exceeding prior work about application of different technologies to obtain such devices, in this work, samples of the polymer/repellent system PLLA/IR3535 were prepared by 3D-printing. The experiments showed that it is possible to print 3D-parts containing up to 25 m% repellent, with an only minor loss of repellent during the printing process. For samples containing low amount of repellent, crystallization of PLLA was suppressed due to the rather fast cooling step and the low bed temperature of around 25 °C, being lower than the glass transition temperature of the homogeneous polymer/repellent strands. At higher repellent concentration, due to the lowering of the glass transition temperature to near or even below ambient temperature, the crystallinity slowly increased during storage after printing. For all samples, regardless of the initial repellent concentration, the repellent-release rate increases with temperature, and at ambient temperature the release-time constant is in the order of 10 days. The study successfully proved the applicability of the technology of extrusion-based 3D-printing for the preparation of polymer parts with a specific shape/design containing mosquito-repellent at a concentration which raises the expectation to be used as a repellent delivery-device.

Slow-DEET-Release Mosquito-Repellent System Based on Poly(butylene succinate)

Bio-sourced and biodegradable poly(butylene succinate) (PBS) strands containing up to 40 m% mosquito-repellent N,N-diethyl-3-methylbenzamide (DEET) were obtained by extrusion, for an initial evaluation of the DEET evaporation characteristics and the possible application of such strands as biodegradable slow-release repellent-delivery devices. For DEET concentrations up to 20 m%, DEET is entrapped in the semicrystalline spherulitic superstructure of PBS. In contrast, at higher DEET concentrations, the liquid repellent, at least partially, is not fully incorporated in the PBS spherulites rather than segregates to form an own macrophase. Quantification of the release of DEET to the environment by thermogravimetric analysis at different temperatures between 60 and 100 °C allowed estimation of the evaporation rate at lower service temperatures, suggesting an extremely low release rate with a time constant of the order of magnitude of 1-2 years at 25 °C, independent of the initial concentration.

Properties of Mosquito Repellent-Plasticized Poly(lactic acid) Strands

Poly(lactic acid) (PLA) is an attractive candidate for replacing petrochemical polymers because it is fully biodegradable. This study investigated the potential of PLA as a sustainable and environmentally friendly alternative material that can be developed into commercially viable wearable mosquito repellent devices with desirable characteristics. PLA strands containing DEET and IR3535 were prepared by twin screw extrusion compounding and simultaneously functioned as plasticizers for the polymer. The plasticizing effect was investigated by thermal and rheological studies. DSC studies showed that the addition of DEET and IR3535 into PLA strands reduced the glass transition temperature consistent with predictions of the Fox equation, thus proving their efficiency as plasticizers. The rheology of molten samples of neat PLA and PLA/repellents blends, evaluated at 200 °C, was consistent with shear-thinning pseudoplastic behaviour. Raman studies revealed a nonlinear concentration gradient for DEET in the PLA strand, indicating non-Fickian Type II transport controlling the desorption process. Release data obtained at 50 °C showed initial rapid release followed by a slower, near constant rate at longer times. The release rate data were fitted to a novel modification of the Peppas-Sahlin desorption model.

Crystallization-Induced Polymer Scaffold Formation in the Polymer/Drug Delivery System Poly(l-lactic acid)/Ethyl Butylacetylaminopropionate (PLLA/IR3535)

Polymer/mosquito-repellent scaffolds exhibit increasing importance in long-lasting human skin protection to be used as wearable devices and allowing for controlled release of repellents. In this study, ethyl butylacetylaminopropionate (IR3535) was used as a human and environmental friendly active mosquito-repellent serving as a solvent to form functional poly(l-lactic acid) (PLLA) scaffolds by crystallization-based solid-liquid thermally induced phase separation. Crystallization of PLLA in the presence of IR3535 is faster than melt-crystallization of neat PLLA, and in the investigated concentration range from 5 to 50 mass % PLLA, its maximum crystallization rate increases with the PLLA content, by both, increases of the maximum crystal growth rate and of the nuclei density. By adjusting the polymer concentration and the crystallization temperature, microporous scaffolds of different fine structures are obtained, hosting the mosquito-repellent in intra- and interspherulitic pores for its intended later evaporation.

Solid–liquid–liquid phase envelopes from temperature-scanned refractive index data

A novel method for estimating the upper critical solution temperature (UCST) of N,N-diethyl-m-toluamide (DEET)-polyethylene systems was developed. It was validated using data for the dimethylacetamide (DMA)-alkane systems which showed that refractive index mixing rules, linear in volume fraction, can accurately predict mixture composition for amide-alkane systems. Furthermore, rescaling the composition descriptor with a single adjustable parameter proved adequate to address any asymmetry when modeling the DMA-alkane phase envelopes. This allowed the translation of measured refractive index cooling trajectories of DEET-alkane systems into phase diagrams and facilitated the estimation of the UCST values by fitting the data with an adjusted composition descriptor model. For both the DEET- and DMA-alkane systems, linear behavior of UCST values in either the Flory–Huggins critical interaction parameter, or the alkane critical temperature, with increasing alkane molar mass is evident. The UCST values for polymer diluent systems were estimated by extrapolation using these two complimentary approaches. For the DEET-polyethylene system, values of 183.4 and 180.1 °C respectively were obtained. Both estimates are significantly higher than the melting temperature range of polyethylene. Initial liquid–liquid phase separation is therefore likely to be responsible for the previously reported microporous microstructure of materials formed from this binary system.

Mosquito-repellent controlled-release formulations for fighting infectious diseases

Malaria is a principal cause of illness and death in countries where the disease is endemic. Personal protection against mosquitoes using repellents could be a useful method that can reduce and/or prevent transmission of mosquito-borne diseases. The available repellent products, such as creams, roll-ons, and sprays for personal protection against mosquitoes, lack adequate long-term efficacy. In most cases, they need to be re-applied or replaced frequently. The encapsulation and release of the repellents from several matrices has risen as an alternative process for the development of invention of repellent based systems. The present work reviews various studies about the development and use of repellent controlled-release formulations such as polymer microcapsules, polymer microporous formulations, polymer micelles, nanoemulsions, solid-lipid nanoparticles, liposomes and cyclodextrins as new tools for mosquito-borne malaria control in the outdoor environment. Furthermore, investigation on the mathematical modelling used for the release rate of repellents is discussed in depth by exploring the Higuchi, Korsmeyer-Peppas, Weibull models, as well as the recently developed Mapossa model. Therefore, the studies searched suggest that the final repellents based-product should not only be effective against mosquito vectors of malaria parasites, but also reduce the biting frequency of other mosquitoes transmitting diseases, such as dengue fever, chikungunya, yellow fever and Zika virus. In this way, they will contribute to the improvement in overall public health and social well-being.

Melt-Spun Poly(D,L-lactic acid) Monofilaments Containing N,N-Diethyl-3-methylbenzamide as Mosquito Repellent

Malaria is still a major tropical disease, with Africa particularly burdened. It has been proposed that outdoor protection could aid substantially in reducing the malaria incidence rate in rural African communities. Recently, melt-spun polyolefin fibers containing mosquito repellents have been shown to be promising materials to this end. In this study, the incorporation of N,N‑Diethyl‑3‑methylbenzamide (DEET)-a popular and widely available mosquito repellent-in commercially available, amorphous poly(D,L-lactic acid) (PDLLA) is investigated with the aim of producing biodegradable mosquito-repelling filaments with a reduced environmental impact. It is shown to be possible to produce macroscopically stable PDLLA-DEET compounds containing up to 20 wt.-% DEET that can be melt-spun to produce filaments, albeit at relatively low take-up speeds. A critical DEET content allows for stress-induced crystallization during the spinning of the otherwise amorphous PDLLA, resulting in the formation of α-crystals. Although the mechanical integrity of the filaments is notably impacted by the incorporation of DEET, these filaments show potential as materials that can be used for Malaria vector control.

Phase behavior of solvent-rich compositions of the polymer/drug system poly(butylene succinate) and N,N-diethyl-3-methylbenzamide (DEET)

Poly(butylene succinate) (PBS) is used to produce micro-/nanoporous biodegradable scaffolds, suitable for the release of the mosquito repellent N,N-diethyl-3-methylbenzamide (DEET), based on thermally induced phase separation. For solvent-rich compositions up to 30 m% PBS, it was found that PBS dissolves in DEET at elevated temperatures. During cooling, spherulitic crystallization of PBS occurs, with the crystallization temperature decreasing with the content of DEET and the cooling rate, as determined by cloud-point measurements, differential scanning calorimetry, and polarized-light optical microscopy. Scaffold morphologies of quenched solutions were analyzed by scanning electron microscopy as a function of the polymer concentration and the quenching temperature. These two parameters control the nucleus density/spherulite size, the degree of intermeshing of spherulites, and the intra- and interspherulitic pore size, with the latter typically being of the order of magnitude of few micrometers.

Binary mixtures of semicrystalline polymers with low-molecular-mass compounds: thermal behaviour and phase structure

The results of phase equilibrium studies in mixtures of semicrystalline polymers with low-molecular-mass compounds are summarized and analyzed. A new classification of phase diagrams for such mixtures is proposed. Alternative points of view on the phase composition of semicrystalline polymers are presented. The phase structure evolution during the thermally induced phase separation of mixtures is monitored and the morphology of the forming capillary porous bodies as precursors of polymeric membranes is described. The general regularities concerning the influence of the nature of mixture components, polymer molecular mass, temperature scanning rate and other factors on the topology of phase diagrams are considered. Experimental methods used to construct the phase diagrams of mixtures and to study features of their phase structure are compared.

The bibliography includes 203 references.