Copolyesters based on bibenzoic acids

Selective C(aryl)-O bond cleavage in biorenewable phenolics

Biorefining of lignocellulosic biomass via a lignin first approach delivers a range of products with high oxygen content. Besides pulp, a lignin oil rich in guaiacols and syringols is obtained bearing multiple C(aryl)-OH and C(aryl)-OMe groups, typically named phenolics. Similarly, technical lignin can be used but is generally more difficult to process providing lower yields of monomers. Removal of the hydroxy and methoxy groups in these oxygenated arenes is challenging due to the inherently strong C-O bonds, in addition to the steric and electronic deactivation by adjacent -OH or -OMe groups. Moreover, chemoselective removal of a specific group in the presence of other similar functionalities is non-trivial. Other side-reactions such as ring saturation and transalkylation further complicate the desired reduction process. In this overview, three different selective reduction reactions are considered. Complete hydrodeoxygenation removes both hydroxy and methoxy groups resulting in benzene and alkylated derivatives (BTX type products) which is often complicated by overreduction of the arene ring. Hydrodemethoxylation selectively removes methoxy groups in the presence of hydroxy groups leading to phenol products, while hydrodehydroxylation only removes hydroxy groups without cleavage of methoxy groups giving anisole products. Instead of defunctionalization via reduction transformation of C(aryl)-OH, albeit via an initial derivatization into C(aryl)-OX, into other functionalities is possible and also discussed. In addition to methods applying guaiacols and syringols present in lignin oil as model substrates, special attention is given to methods using mixtures of these compounds obtained from wood/technical lignin. Finally, other important aspects of C-O bond activation with respect to green chemistry are discussed.

Synthesis and Characterization of Novel Wholly Aromatic Copolyesters Based on 4'-Hydroxybiphenyl-3-Carboxylic and 3-Hydroxybenzoic Acids

A series of new wholly aromatic (co)polyesters based on m-substituted bifunctional comonomers-4'-hydroxybiphenyl-3-carboxylic (3HBCA) and 3-hydroxybenzoic (3HBA) acids with molar ratios of 3HBCA:3HBA from 0:100 to 60:40, respectively-was synthesized. NMR and FTIR spectroscopy methods proved the full compliance of the copolymer composition with the target ratio of comonomers, as well as high compositional homogeneity (absence of block sequences). The resulting copolyesters have a sufficiently high molecular weight and their intrinsic viscosity values are in the range of 0.6-0.8 dL/g. Thermal analysis showed that all 3HBCA-3HBA copolyesters are amorphous, and with an increase in the content of biphenyl units (3HBCA), the glass transition temperature increases significantly (up to 190 °C). The onset of the intense thermal decomposition of the synthesized polyesters occurs above 450 °C. Thus, this indicates a sufficiently high thermal stability of these polyesters. Rheological measurements have shown that melts of copolyesters with a high content of 3HBCA units exhibit anisotropic properties. At the same time, the method of polarization optical microscopy did not confirm the transition to the liquid crystal state for these polyesters. These results confirm that it is possible to obtain high-performance polyesters based on 3HBCA, but not a mesogenic comonomer. Thus, 3HBCA is a promising comonomer for the synthesis of new thermotropic copolyesters with controlled anisotropic properties.

Ni- and Ni/Pd-Catalyzed Reductive Coupling of Lignin-Derived Aromatics to Access Biobased Plasticizers

Lignin-derived aromatic chemicals offer a compelling alternative to petrochemical feedstocks, and new applications are the focus of extensive interest. 4-Hydroxybenzoic acid (H), vanillic acid (G), and syringic acid (S) are readily obtained via oxidative depolymerization of hardwood lignin substrates. Here, we explore the use of these compounds to access biaryl dicarboxylate esters that represent biobased, less toxic alternatives to phthalate plasticizers. Chemical and electrochemical methods are developed for catalytic reductive coupling of sulfonate derivatives of H, G, and S to access all possible homo- and cross-coupling products. A conventional NiCl₂/bipyridine catalyst is able to access the H-H and G-G products, but new catalysts are identified to afford the more challenging coupling products, including a NiCl₂/bisphosphine catalyst for S-S and a NiCl₂/phenanthroline/PdCl₂/phosphine cocatalyst system for H-G, H-S, and G-S. High-throughput experimentation methods with a chemical reductant (Zn powder) are shown to provide an efficient screening platform for identification of new catalysts, while electrochemical methods can access improved yields and/or facilitate implementation on larger scale. Plasticizer tests are performed with poly(vinyl chloride), using esters of the 4,4'-biaryl dicarboxylate products. The H-G and G-G derivatives, in particular, exhibit performance advantages relative to an established petroleum-based phthalate ester plasticizer.