Use of capnography to verify emergency ventilator sharing in the COVID-19 era

Ventilator output splitting interface 'ACRA': Description and evaluation in lung simulators and in an experimental ARDS animal model

The current COVID-19 pandemic has led the world to an unprecedented global shortage of ventilators, and its sharing has been proposed as an alternative to meet the surge. This study outlines the performance of a preformed novel interface called 'ACRA', designed to split ventilator outflow into two breathing systems. The 'ACRA' interface was built using medical use approved components. It consists of four unidirectional valves, two adjustable flow-restrictor valves placed on the inspiratory limbs of each unit, and one adjustable PEEP valve placed on the expiratory limb of the unit that would require a greater PEEP. The interface was interposed between a ventilator and two lung units (phase I), two breathing simulators (phase II) and two live pigs with heterogeneous lung conditions (phase III). The interface and ventilator adjustments tested the ability to regulate individual pressures and the resulting tidal volumes. Data were analyzed using Friedman and Wilcoxon tests test (p < 0.05). Ventilator outflow splitting, independent pressure adjustments and individual tidal volume monitoring were feasible in all phases. In all experimental measurements, dual ventilation allowed for individual and tight adjustments of the pressure, and thus volume delivered to each paired lung unit without affecting the other unit's ventilation-all the modifications performed on the ventilator equally affected both paired lung units. Although only suggested during a dire crisis, this experiment supports dual ventilation as an alternative worth to be considered.

Sharing Mechanical Ventilator: In Vitro Evaluation of Circuit Cross-Flows and Patient Interactions

During the COVID-19 pandemic, a shortage of mechanical ventilators was reported and ventilator sharing between patients was proposed as an ultimate solution. Two lung simulators were ventilated by one anesthesia machine connected through two respiratory circuits and T-pieces. Five different combinations of compliances (30–50 mL × cmH₂O⁻¹) and resistances (5–20 cmH₂O × L⁻¹ × s⁻¹) were tested. The ventilation setting was: pressure-controlled ventilation, positive end-expiratory pressure 15 cmH₂O, inspiratory pressure 10 cmH₂O, respiratory rate 20 bpm. Pressures and flows from all the circuit sections have been recorded and analyzed. Simulated patients with equal compliance and resistance received similar ventilation. Compliance reduction from 50 to 30 mL × cmH₂O⁻¹ decreased the tidal volume (V_T) by 32% (418 ± 49 vs. 285 ± 17 mL). The resistance increase from 5 to 20 cmH₂O × L⁻¹ × s⁻¹ decreased V_T by 22% (425 ± 69 vs. 331 ± 51 mL). The maximal alveolar pressure was lower at higher compliance and resistance values and decreased linearly with the time constant (r² = 0.80, p < 0.001). The minimum alveolar pressure ranged from 15.5 ± 0.04 to 16.57 ± 0.04 cmH₂O. Cross-flows between the simulated patients have been recorded in all the tested combinations, during both the inspiratory and expiratory phases. The simultaneous ventilation of two patients with one ventilator may be unable to match individual patient’s needs and has a high risk of cross-interference.

Combined Ventilation of Two Subjects with a Single Mechanical Ventilator Using a New Medical Device: An In Vitro Study

Introduction

The SARS-CoV-2 pandemic has created a sudden lack of ventilators. DuplicAR^Ⓡ is a novel device that allows simultaneous and independent ventilation of two subjects with a single ventilator. The aims of this study are (a) to determine the efficacy of DuplicAR^Ⓡ to independently regulate the peak and positive-end expiratory pressures in each subject, both under pressure-controlled ventilation and volume-controlled ventilation and (b) to determine the ventilation mode in which DuplicAR^Ⓡ presents the best performance and safety.

Materials and Methods

Two test lungs are connected to a single ventilator using DuplicAR^Ⓡ. Three experimental stages are established: (1) two identical subjects, (2) two subjects with the same weight but different lung compliance, and (3) two subjects with different weights and lung compliances. In each stage, the test lungs are ventilated in two ventilation modes. The positive-end expiratory pressure requirements are increased successively in one of the subjects. The goal is to achieve a tidal volume of 7 ml/kg for each subject in all different stages through manipulation of the ventilator and the DuplicAR^Ⓡ controllers.

Results

DuplicAR^Ⓡ allows adequate ventilation of two subjects with different weights and/or lung compliances and/or PEEP requirements. This is achieved by adjusting the total tidal volume for both subjects (in volume-controlled ventilation) or the highest peak pressure needed (in pressure-controlled ventilation) along with the basal positive-end expiratory pressure on the ventilator and simultaneously manipulating the DuplicAR^Ⓡ controllers to decrease the tidal volume or the peak pressure in the subject that needs less and/or to increase the positive-end expiratory pressure in the subject that needs more. While ventilatory goals can be achieved in any of the ventilation modes, DuplicAR^Ⓡ performs better in pressure-controlled ventilation, as changes experienced in the variables of one subject do not modify the other one.

Conclusions

DuplicAR^Ⓡ is an effective tool to manage the peak inspiratory pressure and the positive-end expiratory pressure independently in two subjects connected to a single ventilator. The driving pressure can be adjusted to meet the requirements of subjects with different weights and lung compliances. Pressure-controlled ventilation has advantages over volume-controlled ventilation and is therefore the recommended ventilation mode.