A new and highly selective turn-on fluorescent sensor with fast response time for the monitoring of cadmium ions in cosmetic, and health product samples

Label-free fluorescence aptasensor for the detection of cadmium(II) ion based on the conformational switching of aptamer and thioflavine T

A simple label-free Cd2+ fluorescent aptasensor was proposed using aptamer as a recognition element and thioflavine T (ThT) as a signal reporter. The presence of Cd(II) can induce the conformational switching of the aptamer probe, accompanied by a change in fluorescence intensity. According to the difference in fluorescence signals before and after the addition of Cd2+, a fluorescence sensor for Cd2+ assay was established. Under the better experimental conditions, the sensor displayed a good linear range from 2 to 50 nM and the excellent detection limit was 0.8 nM. The method demonstrated high sensitivity and good selectivity. The aptasensor could detect Cd2+ in simulated water samples with satisfactory results. The proposed method had obvious advantages that was without chemical modification of fluorescent groups and complicated target preconcentration. It provided a new analytical platform for the detection of heavy metal ion pollution in environmental and biomedical fields.

Rapid Detection of Cd2+ Ions in the Aqueous Medium Using a Highly Sensitive and Selective Turn-On Fluorescent Chemosensor

Herein, a novel optical chemosensor, (CM1 = 2, 6-di((E)-benzylidene)-4-methylcyclohexan-1-one), was designed/synthesized and characterized by ¹H-NMR and FT-IR spectroscopy. The experimental observations indicated that CM1 is an efficient and selective chemosensor towards Cd²⁺, even in the presence of other metal ions, such as Mn²⁺, Cu²⁺, Co^2+, Ce³⁺, K⁺, Hg²⁺,^, and Zn²⁺ in the aqueous medium. The newly synthesized chemosensor, CM1, showed a significant change in the fluorescence emission spectrum upon coordination with Cd²⁺. The formation of the Cd²⁺ complex with CM1 was confirmed from the fluorometric response. The 1:2 combination of Cd²⁺ with CM1 was found optimum for the desired optical properties, which was confirmed through fluorescent titration, Job's plot, and DFT calculation. Moreover, CM1 showed high sensitivity towards Cd²⁺ with a very low detection limit (19.25 nM). Additionally, the CM1 was recovered and recycled by the addition of EDTA solution that combines with Cd²⁺ ion and, hence, frees up the chemosensor.

Introducing Graphene–Indium Oxide Electrochemical Sensor for Detecting Ethanol in Aqueous Samples with CCD-RSM Optimization

There is significant demand for portable sensors that can deliver selective and sensitive measurement of ethanol on-site. Such sensors have application across many industries, including clinical and forensic work as well as agricultural and environmental analysis. Here, we report a new graphene–indium oxide electrochemical sensor for the determination of ethanol in aqueous samples. Graphene layers were functionalised by anchoring In2O3 to its surface and the developed composite was used as a selective electrochemical sensor for sensing ethanol through cyclic voltammetry. The detection limit of the sensor was 0.068 mol/L and it showed a linear response to increasing ethanol in the environment up to 1.2 mol/L. The most significant parameters involved and their interactions in the response of the sensor and optimization procedures were studied using a four-factor central composite design (CCD) combined with response surface modelling (RSM). The sensor was applied in the detection of ethanol in authentic samples.

Recent Advances in Porphyrin-Based Materials for Metal Ions Detection

Porphyrins have planar and conjugated structures, good optical properties, and other special functional properties. Owing to these excellent properties, in recent years, porphyrins and their analogues have emerged as a multifunctional platform for chemical sensors. The rich chemistry of these molecules offers many possibilities for metal ions detection. This review mainly discusses two types of molecular porphyrin and porphyrin composite sensors for metal ions detection, because porphyrins can be functionalized to improve their functional properties, which can introduce more chemical and functional sites. According to the different application materials, the section of porphyrin composite sensors is divided into five sub-categories: (1) porphyrin film, (2) porphyrin metal complex, (3) metal–organic frameworks, (4) graphene materials, and (5) other materials, respectively.

A water-soluble BODIPY based 'OFF/ON' fluorescent probe for the detection of Cd2+ ions with high selectivity and sensitivity

A water-soluble dilithium salt BODIPY derivative (LiBDP) with appended dicarboxylate pseudo-crown ether [NO4] coordinating sites has been designed, synthesized and characterized successfully for the selective and sensitive recognition of Cd2+ in aqueous media. The chemosensor exhibits a remarkable increase in fluorescence intensity as well as a distinct color change upon the addition of Cd2+ over other environmentally and biologically relevant metal ions in H2O. The fluorometric response of LiBDP is attributed to the metal chelation-enhanced fluorescence (MCHEF) effect which has been confirmed by a strong association constant of 2.57 ± 1.06 × 105 M-1 and Job's plot, indicating 1 : 1 binding stoichiometry between LiBDP and Cd2+. Frontier molecular orbital analysis (obtained from DFT studies) also illustrates the turn-on fluorescence of the probe by blocking photoinduced electron transfer (PET) after coordination to Cd2+. The probe can detect Cd2+ in a competitive environment up to a submicromolar level in a biologically significant pH range. The sensor is proved to be reversible and reusable by the alternative addition of Cd2+ followed by S2-. The OFF/ON/OFF sensing behavior is utilized to construct an INHIBIT molecular logic gate based on the two inputs of Cd2+ and S2- and a fluorescence intensity at 512 nm as an output. The test paper experiment demonstrates the practical utility of LiBDP to monitor Cd2+ in an aqueous sample. Finally, the sensing probe was utilized to monitor Cd2+ in living cells.

A bifunctional sensor based on diarylethene for the colorimetric recognition of Cu2+ and fluorescence detection of Cd2+

A novel bifunctional sensor based on diarylethene with a benzyl carbazate unit was synthesized successfully. It not only served as a colorimetric sensor for the recognition of Cu²⁺ by showing changes in absorption spectra and solution color, but also acted as a fluorescent sensor for the detection of Cd²⁺ through obvious emission intensity enhancement and fluorescence color change. The sensor exhibited excellent selectivity and sensitivity towards Cu²⁺ and Cd²⁺, and the limits of detection for Cu²⁺ and Cd²⁺ were 8.36 × 10⁻⁸ mol L⁻¹ and 1.71 × 10⁻⁷ mol L⁻¹, respectively, which were much lower than those reported by the WHO and EPA in drinking water. Furthermore, its application in practical samples demonstrated that the sensor can be effectively applied for the detection of Cu²⁺ and Cd²⁺ in practical water samples.

A bifunctional sensor for colorimetric recognition of Cu²⁺ and fluorescent detection of Cd²⁺ was synthesized. It not only showed high selectivity and sensitivity to Cu²⁺ and Cd²⁺, but also could be used in practical water samples with high accuracy.

Fluorescence turn-on sensing of trace cadmium ions based on EDTA-etched CdTe@CdS quantum dot

Cadmium-caused environmental pollution and diseases have always been worldwide problems. Thus it is extremely urgent to establish a cheap, rapid, simple and selective detection method for trace cadmium in drinking water. In this study, a fluorescence "turn-on" method based on ethylene diamine tetraacetic acid (EDTA)-etched CdTe@CdS quantum dots (QDs) was designed to detect Cd²⁺. High resolution transmission electron microscopy (HRTEM) and X-ray photoelectron spectroscopy (XPS) were utilized for chemical and structural characterization of the as-prepared QDs. Based on chemical etching of EDTA on the surface of CdTe@CdS QDs, specific Cd²⁺ recognition sites were produced, and then results in fluorescence quenching. The introduction of Cd²⁺ could identify these sites and restore the fluorescence of the EDTA-QDs system. Under the optimum conditions, the nanoprobe shows a linear response range from 0.05 to 9 μM with a very low detection limit of 0.032 μM. In addition, the reported fluorescence probe in this work displays a good selectivity for trace Cd²⁺ over other metal ions and an admirable practicability in real water samples.

Application of magnetic ionomer for development of very fast and highly efficient uptake of triazo dye Direct Blue 71 form different water samples

This research focuses on removing Direct Blue 71 (DB 71) from aqueous solution in an efficient and very fast route by ionic liquid mediated γ-Fe₂O₃ magnetic ionomer. 2-hydroxyethylammonium sulphonate immobilized on γ-Fe₂O₃ nanoparticles (γ-Fe₂O₃-2-HEAS) was used for this purpose. The influence of shaking time, medium pH, the concentration of sorbent and NaNO₃ on removal was evaluated to greatly influence removal extent. The optimal removal conditions were determined by response surface methodology based on the four-variable central composite design to obtain maximum removal efficiency and determine the significance and interaction effect of the variables on the removal of target triazo dye. The results have shown that an amount of 98.2% as % removal under the optimum conditions. The adsorption kinetics and isotherms were well fitted to a pseudo-second order model and Freundlich model, respectively. Based on these models, the maximum dye adsorption capacity (Q_m) of 47.60mgg^-1 was obtained. Finally, the proposed nano-adsorbent was applied satisfactorily for removal of target triazo dye from different water samples.

A Ratiometric Fluorescent Sensor for Cd2+ Based on Internal Charge Transfer

This work reports on a novel fluorescent sensor 1 for Cd²⁺ ion based on the fluorophore of tetramethyl substituted bis(difluoroboron)-1,2-bis[(1H-pyrrol-2-yl)methylene]hydrazine (Me₄BOPHY), which is modified with an electron donor moiety of N,N-bis(pyridin-2-ylmethyl)benzenamine. Sensor 1 has absorption and emission in visible region, at 550 nm and 675 nm, respectively. The long wavelength spectral response makes it easier to fabricate the fluorescence detector. The sensor mechanism is based on the tunable internal charge transfer (ICT) transition of molecule 1. Binding of Cd²⁺ ion quenches the ICT transition, but turns on the π − π transition of the fluorophore, thus enabling ratiometric fluorescence sensing. The limit of detection (LOD) was projected down to 0.77 ppb, which is far below the safety value (3 ppb) set for drinking water by World Health Organization. The sensor also demonstrates a high selectivity towards Cd²⁺ in comparison to other interferent metal ions.

Dithizone-etched CdTe nanoparticles-based fluorescence sensor for the off–on detection of cadmium ion in aqueous media

In the present work, a new fluorescence probe based on dithizone-etched CdTe nanoparticles was designed for the sensitive and selective detection of cadmium ion in environmental samplesviaa reversible off–on fluorescence mode.

A coumarin–chalcone hybrid used as a selective and sensitive colorimetric and turn-on fluorometric sensor for Cd2+ detection

A chalcone-based naked-eye colorimetric chemical sensor, (E)-4-hydroxy-3-(3-(4-methoxyphenyl)acryloyl)-2H-chromen-2-one 1a, was developed for selective and sensitive recognition of Cd²⁺ in mixed aqueous–organic media.