Modeling and monitoring cyclic and linear volatile methylsiloxanes in a wastewater treatment plant using constant water level sequencing batch reactors

Unraveling the distribution characteristic of cyclic volatile methylsiloxanes in various environmental media of a wastewater treatment plant

Cyclic volatile methylsiloxane (cVMS) is extensively used in consumer products and frequently detected in various environmental media, including water and air. In this study, we developed reliable and convenient methods to sample three cVMS compounds: octamethylcyclotetrasiloxane (D4), decamethylcyclopentasiloxane (D5), and dodecamethylcyclohexasiloxane (D6) in water and air samples collected from different tanks within a wastewater treatment plant (WWTP). The concentrations of D4, D5, and D6 in the water samples ranged from 0.40 to 8.0 μg L-1, 0.35 to 91 μg L-1, and 0.54 to 17 μg L-1, respectively. In the air samples, these concentrations varied from 0.34 to 20 μg m-3, 0.34 to 128 μg m-3, and 0.08 to 12 μg m-3, respectively. It is worth noting that the air-water distribution coefficient (Kaw) for these three cVMS exhibited a strong correlation with their water solubility. Moreover, fugacity fractions indicated a net evaporation process from water to the atmosphere. Furthermore, we investigated the distribution of cVMS between the gaseous and particulate phases. The results revealed a significant fraction, exceeding 72 %, of cVMS resided in the gas phase. D4 and D5 predominate in the gaseous phase, while D5 and D6 are the principal constituents within the particulate phase. The distribution coefficient characterizing the partitioning of cVMS compounds between the gaseous and particulate (Kp) exhibited a strong correlation with their corresponding octanol-air partitioning coefficients (Koa). These findings contribute to a better understanding of the distribution of cVMS in diverse environmental media and the underlying mechanism governing their dispersion.

Helping WWTP managers to address the volatile methylsiloxanes issue-Behaviour and complete mass balance in a conventional plant

Volatile methylsiloxanes (VMSs) are a group of additives employed in different consumer products that can affect the quality of the biogas produced in wastewater treatment plants (WWTPs). The main objective of this study is to understand the fate of different VMSs along the treatment process of a WWTP located in Aveiro (Portugal). Thus, wastewater, sludge, biogas, and air were sampled in different units for two weeks. Subsequently, these samples were extracted and analyzed by different environment-friendly protocols to obtain their VMS (L3-L5, D3-D6) concentrations and profiles. Finally, considering the different matrix flows at every sampling moment, the mass distribution of VMSs within the plant was estimated. The levels of ∑VMSs were similar to those showed in the literature (0.1-50 μg/L in entry wastewater and 1-100 μg/g dw in primary sludge). However, the entry wastewater profile showed higher variability in D3 concentrations (from non detected to 49 μg/L) than found in previous studies (0.10-1.00 μg/L), likely caused by isolated releases of this compound that could be related to industrial sources. Outdoor air samples showed a prevalence of D5, while indoor air locations were characterized by a predominance of D3 and D4. Differences in sources and the presence of an indoor air filtration system may explain this divergence. Biogas was characterized by ∑VMSs concentrations (8.00 ± 0.22 mg/m3) above the limits recommended by some engine manufacturers and mainly composed of D5 (89%). Overall, 81% of the total incoming mass of VMSs is reduced along the WWTP, being the primary decanter and the secondary treatment responsible for the highest decrease (30.6% and 29.4% of the initial mass, respectively). This reduction, however, is congener dependant. The present study demonstrates the importance of extending sampling periods and matrices (i.e., sludge and air) to improve sample representativity, time-sensitivity, and the accuracy of mass balance exercises.

Volatile Methylsiloxanes in Complex Samples: Recent Updates on Pretreatment and Analysis Methods

Volatile methylsiloxanes (VMSs) are massively produced chemicals having applications in industry and home because of their physical and chemical characteristics. They are used in personal care products such as cosmetics, household coatings, cleaners, skin care products, and others. Resultantly, large number of VMSs are discharged into air where they can be subjected to atmospheric migrations over long distances causing toxic and estrogenic effects, persistence, and bioaccumulations. Many institutions have taken measures to control VMSs. They require accurate, rapid, and sensitive pretreatment and analysis methods for diverse samples. Herein, the pretreatment and determination methods of VMSs as reported in recent years are reviewed and summarized. Pretreatments include commonly methods such as membrane-assisted solvent extraction, liquid-liquid extraction, and others, while novel methods are solid phase extraction, solid phase microextraction, diverse liquid phase microextraction and others. Analyses are made through gas chromatography-based methods. In addition, the advantages, and disadvantages of techniques are compared, and the prospects of pretreatment and analysis methods are discussed.

Cyclic volatile methyl siloxanes (D4, D5, and D6) as the emerging pollutants in environment: environmental distribution, fate, and toxicological assessments

Cyclic volatile methyl siloxanes (cVMS) have now become a subject of environmental contamination and risk assessment due to their widespread use and occurrence in different environmental matrices. Due to their exceptional physio-chemical properties, these compounds are diversely used for formulations of consumer products and others implying their continuous and significant release to environmental compartments. This has captured the major attention of the concerned communities on the grounds of potential health hazards to human and biota. The present study aims at comprehensively reviewing its occurrence in air, water, soil, sediments, sludge, dusts, biogas, biosolids, and biota and their environmental behavior as well. Concentrations of cVMS in indoor air and biosolids were higher; however, no significant concentrations were observed in water, soil, and sediments except for wastewaters. No threat to the aquatic organisms has been identified as their concentrations do not exceed the NOEC (maximum no observed effect concentration) thresholds. Mammalian (rodents) toxicity hazards were not very evident except for the occurrence of uterine tumors in very rare cases under long-term chronic and repeated dose exposures in laboratory conditions. Human relevancy to rodents were also not strongly enough established. Therefore, more careful examinations are required to develop stringent weight of evidences in scientific domain and ease the policy making with respect to their production and use so as to combat any environmental consequences.

Fate of household and personal care chemicals in typical urban wastewater treatment plants indicate different seasonal patterns and removal mechanisms

Studies on the presence and fate of household and personal care chemicals (HPCCs) in wastewater treatment plants (WWTPs) are important due to their increasing consumption worldwide. The seasonal patterns and removal mechanisms of HPCCs are not well understood for WWTPs that apply different treatment technologies. To answer these questions, the sewage and sludge samples were taken from 10 typical WWTPs in Northeast China. Levels of UV filters in the influents in the warm season were significantly greater than that of the cold season (p < 0.05). Significant seasonal differences were found for the removals of many HPCCs. Results revealed that the highest removal efficiencies were found for linear alkylbenzene sulphonates with values ranging from 97.2% to 99.7%, and the values were 50.0%-99.9% for other HPCCs. The SimpleTreat model demonstrated that the studied WWTPs were operating with high efficiency at the time of sampling. The sorption of HPCCs to sludge can be strongly associated with their physicochemical parameters. Mass balance calculation suggested that sorption was the dominant mechanism for the removal of antimicrobials, while degradation and/or biotransformation were the other mechanisms for removing the most HPCCs in the WWTPs. This study real the factors influencing the seasonal patterns and removal mechanisms which imply the need for further studies to fully understands the plant and human health implications as sludge could be used in the municipal land application of biosolids.

Suspect screening analysis of the occurrence and removal of micropollutants by GC-QTOF MS during wastewater treatment processes

The presence of micropollutants in wastewater treatment plant (WWTP) poses potential risks to the aquatic system and human health. This study comprehensively characterized the presence, elimination, and transformation of micropollutants in the WWTP using the suspect screening approaches by employing the gas chromatography coupled with quadrupole time-of-flight mass spectrometry. Overall, 5724 features were identified in influent, while only 3418 features existed in effluents. Hierarchical cluster analysis (HCA) was used to group features based on intensity profiles to investigate the behavior and fate of detected features. Four representative trends were defined with the corresponding features. Among 117 compounds identified during the treatment process, there were 99 compounds in influent, 10 biological transformation products (TPs), 3 ozone TPs, and 5 ultraviolet TPs. Furthermore, the removal efficiencies for the detected compounds were determined. The study findings highlight the importance of the removal of emerging pollutants and TPs such as fipronil, fipronil sulfide, and fipronil sulfone.

Evolution of consciousness of exposure to siloxanes-review of publications

The purpose of this description is to review scientific literature from 1944 to 2017 as a source of information on the reasons for the increased interest in siloxanes (silicones). Not only the research area, but first, the changes in the tendency of research aims are important issues in the evaluation. On the one hand, the authors emphasize the unique properties of linear and cyclic siloxanes, providing many examples of beneficial applications, and on the other hand, there are some warnings of overcoming of the safety barrier of their presence in human environment. Analyzing the results from the SCOPUS database, it can be argued that the increased interest of scientists and government agencies particularly relates to the analysis of siloxanes in biological and environmental samples. This is caused not only by the widespread use of various siloxanes in the pharmaceutical, medical, cosmetic and food industries, but also by the direct contact of these compounds with tissues, as well as an increased access to knowledge and modern research tools that have developed the awareness of hazards. The development of research methods enables not only constant monitoring of progressively lower siloxanes concentrations in various samples, but because of the specificity of these methods, it also enables an identification of specific siloxane compounds and evaluation of their effects on humans and environment. This paper discusses the issues of the evolution of consciousness of exposure to siloxanes due to their increased synthesis and widespread use in many areas of human life, which contributes to environmental pollution.

Volatile methylsiloxanes through wastewater treatment plants - A review of levels and implications

The use of siloxanes has been increasing due to physicochemical properties that are appropriate to be included in the formulations of a large variety of consumer products. This implies a considerable release of these chemicals into the environment, which caught the attention of the scientific community in view of some reports of potential hazardous effects. However, the studies related to the presence and partition of volatile methylsiloxanes (VMSs) in wastewater treatment plants (WWTPs) are still scarce. The aim of this review is to provide a comprehensive assessment of the current state of the knowledge concerning the presence of VMSs in WWTPs and also a discussion of the efficiency of the removal technologies available. Levels, fate and behaviour of VMSs in WWTPs were reviewed, covering not only the water and sludge lines during the treatment processes, but also in the surrounding air. Several approaches for the analysis of VMSs within the WWTPs have been developed to cope with the complexity of the mentioned matrices, which led to sometimes challenging protocols. Hence, an overview of methodologies normally used was also included in the present review. Regarding the wastewater samples, VMSs have been detected in influents in concentrations ranging from a few nanograms to a hundred micrograms per litre, in which linear VMSs were usually detected in lower levels than cyclic siloxanes. The levels of VMSs in effluents were lower than those found in influents, suggesting an effective removal from the water line. However, they are commonly accumulating in the sludge, instead of suffering degradation during the treatment process. Therefore, due to the volatile character of VMSs it can be expected that a fraction may be removed in WWTPs by volatilization, thus completing the mass balances to the whole treatment facilities.

Using mechanisms of hydrolysis and sorption to reduce siloxanes occurrence in biogas of anaerobic sludge digesters

Hydrolysis of hexamethylcyclotrisiloxane (D3), octamethylcyclotetrasiloxane (D4), decamethylcyclopentasiloxane (D5), dodecamethylcyclohexasiloxane (D6) and dodecamethylcyclohexasilane (D6_silane) and their sorption to digested sludge was studied in batch experiments. Hydrolysis was affected by the type of the compound and the applied temperature, while the relevant half-life values ranged between 0.07±0.01d (D3, 55°C) and 48.4±17.1d (D6_silane, 4°C). D5 showed the greatest affinity for sorption to digested sludge (logK_d: 3.84±3.42), the lowest LogK_d value was found for D3 (1.46±0.95). Prediction of investigated compounds' fate in a single-stage anaerobic digestion system indicated that volatilization seems to be the major fate in both mesophilic and thermophilic conditions. The addition of a pre-digester with 3d retention time would significantly decrease the expected concentrations of all siloxanes in biogas, enhancing their removal through hydrolysis and sorption to sludge.

From the shop to the drain - Volatile methylsiloxanes in cosmetics and personal care products

Organosiloxanes are widely used in the formulation of a broad range of cosmetic and personal care products (PCPs), including creams and lotions, bath soaps, shampoo and hair care products to soften, smooth, and moisten. In fact, the intensive and widespread use of organosiloxanes combined with their lipophilic nature, makes them interesting targets for future research, particularly in the toxicology area. This study focused on determining the concentration levels of these compounds in the bestselling brands of PCPs in the Oporto region (Portugal), allowing the estimation of dermal and inhalation exposure to siloxanes and the evaluation of the quantities released to the environment "down-the-drain" and to air. To accomplish this task, a QuEChERS technique ("Quick, Easy, Cheap, Effective, Rugged, and Safe") was employed to extract the siloxanes from the target PCPs, which has never been tested before. The resulting extract was analysed by gas chromatography-mass spectrometry (GC-MS). The limits of detection varied between 0.17 (L2) and 3.75ngg(-1) (L5), being much lower than any values reported in the literature for this kind of products. In general, satisfactory precision (<10%) and accuracy values (average recovery of 84%) were obtained. 123 PCPs were analysed (moisturizers, deodorants, body and hair washes, toilet soaps, toothpastes and shaving products) and volatile methylsiloxanes were detected in 96% of the samples, in concentrations between 0.003μgg(-1) and 1203μgg(-1). Shampoo exhibited the highest concentration for cyclic and aftershaves for linear siloxanes. Combining these results with the daily usage amounts, an average daily dermal exposure of 25.04μgkgbw(-1)day(-1) for adults and 0.35μgkgbw(-1)day(-1) for baby/children was estimated. The main contributors for adult dermal exposure were body moisturizers, followed by facial creams and aftershaves, while for babies/children were body moisturizers, followed by shower gel and shampoo. Similarly, the average daily inhalation exposure was also estimated. Values of 1.56μgkgbw(-1)day(-1) for adults and 0.03μgkgbw(-1)day(-1) for babies/children were calculated. An estimate of the siloxanes amount released "down-the-drain" into the sewage systems through the use of toiletries was also performed. An emission per capita between 49.25 and 9574μgday(-1) (mean: 1817μgday(-1)) is expected and shampoo and shower gel presented the higher mean total values (1008μgday(-1) and 473.3μgday(-1), respectively). In the worst-case scenario, D5 and D3 were the predominant siloxanes in the effluents with 3336μgday(-1) and 3789μgday(-1), respectively. Regarding the air emissions per capita, values between 8.33 and 6109μgday(-1) (mean: 1607μgday(-1)) are expected and D5 and D6 were the predominant siloxanes.