Customized thin and loose cake layer to mitigate membrane fouling in an electro-assisted anaerobic forward osmosis membrane bioreactor (AnOMEBR)

Photocatalytic hydrogel film assisted forward osmosis (PFO) for water treatment: Sustainable performance and contaminant control

The integration of catalytic oxidation with forward osmosis (FO) holds promising potential to address two crucial challenges encountered by FO: fouling and unsustainable performance, but suitable approaches are still rare. Herein, we have successfully developed a photocatalysis-assisted forward osmosis (PFO) system. In the PFO, a self-made porous carbon nitride doped functional carbon nanotube photocatalytic hydrogel film (PCN@CNTM) was engaged in the FO process in an inventive way by simply sticking to the commercial FO membrane surface, preventing damage to the membrane from the catalyst's direct insertion and delaying the assault from the oxidation groups. PFO allowed organic pollutants to decompose in the feed solution (90%) and on the membrane surface, regulating the water chemical potential and giving the FO membrane antifouling properties. This resulted in sustainable water flux (11.8 LMH) with no significant membrane fouling in PFO, whereas in FO alone there was a significant fouling and flux drop (from 12.73 to 7.23 LMH in 4 h). Moreover, the expensive FO membrane was protected while the hydrogel film can be replaced on demand. The PFO exemplifies the concept of synergistic technology integration, presenting a new perspective on harnessing the strengths of distinct technologies in a mutually beneficial manner.

In-situ cathodic electrolysis coupled with hydraulic backwash inhibited biofilm formation on a backwashable carbon nanotube membrane

Electro-coupled membrane filtration (ECMF) is an innovative and green technology for water and wastewater treatment. However, the dynamics of biofouling development in the ECMF system has yet been determined. This fundamental question was systematically investigated in this study through laboratory dead-end ECMF experiments. It was found that the ECMF process with an applied voltage of 3 V and a backwash interval of 60 min was capable of completely eradicating membrane biofouling in an extended filtration time of 1450 min. In contrast, membrane biofouling was much severer with a longer backwash interval of 720 min or without backwash. The complemental permeate analysis and membrane characterization results revealed that biofouling during ECMF involved two sequential stages. During the first stage, dead bacteria and their degradation debris formed a loose deposit layer on the membrane surface. The continuous accumulation of this layer decreased the electrochemical performance of the membrane cathode. As such, bacteria in the top deposit layer proliferated and secreted extracellular polymeric substances, which led to irreversible fouling in the second stage. Therefore, timely removal of the initial deposit layer by hydraulic backwash was crucial in preventing irreversible membrane biofouling. These findings provided novel insights into the synergistic effects of cathodic electrolysis and hydraulic backwash for biofouling mitigation.

Evaluation of aquaporin based biomimetic forward osmosis membrane in terms of rejection performance for contaminants in greywater and its membrane fouling properties

Forward osmosis (FO) technology is regarded as an alternative to wastewater treatment due to its high permeate flux, excellent solute selectivity and low fouling tendency. In this study, two novel aquaporin based biomimetic membranes (ABMs) were used for comparison in short-term experiments to investigate the impact of membrane surface properties on greywater treatment. The impact of feed solution (FS) temperature on the filtration performance and membrane fouling behavior of ABM was further analyzed in the sequential batch experiments. Results indicated that the membranes with rough surface morphology and low zeta potential (absolute value) facilitated the adsorption of linear alklybezene sulfonates (LAS), thus improving the water flux and the rejection of Ca²⁺ and Mg²⁺. The increase in FS temperature enhanced the diffusion of organic matter and the water flux. In addition, sequential batch experiments showed that the membrane fouling layer was mainly in the form of organic and inorganic composite fouling, which was mitigated at FS temperature of 40 °C. Microbial community analysis revealed that the increase in FS temperature affected the diversity of microbial communities. More heterotrophic nitrifying bacteria were enriched in the fouling layer at FS 40 °C than at FS 20 °C. This study provides a novel strategy for employing ABM FO in greywater treatment and reuse.

Anaerobic membrane bioreactors for pharmaceutical-laden wastewater treatment: A critical review

Pharmaceuticalsare a diverse group of chemical compounds widely used for prevention and treatment of infectious diseases in both humans and animals. Pharmaceuticals, either in their original or metabolite form, find way into the wastewater treatment plants (WWTPs) from different sources. Recently, anaerobic membrane bioreactors (AnMBR) has received significant research attention for the treatment of pharmaceuticals in various wastewater streams. This review critically examines the behaviour and removal of a wide array of pharmaceuticals in AnMBR with primary focus on their removal efficiencies and mechanisms, critical influencing factors, and the microbial community structures. Subsequently, the inhibitory effects of pharmaceuticals on the performance of AnMBR and membrane fouling are critically discussed. Furthermore, the imperative role of membrane biofouling layer and its components in pharmaceuticals removal is highlighted. Finally, recent advancements in AnMBR configurations for membrane fouling control and enhanced pharmaceuticals removal are systemically discussed.

Enhanced understanding of osmotic membrane bioreactors through machine learning modeling of water flux and salinity

Mathematical modeling can be helpful to understand and optimize osmotic membrane bioreactors (OMBR), a promising technology for sustainable wastewater treatment with simultaneous water recovery. Herein, seven machine learning (ML) algorithms were employed to model both water flux and salinity of a lab-scale OMBR. Through the optimum hyperparameters tuning and 5-fold cross-validation, the ML models have achieved more accurate results without obvious overfitting and bias. The median R² scores of water flux modeling were all over the 0.95 and the most of median R² scores from total dissolved solids (TDS) modeling were higher than 0.90. During model testing, random forest (RF) algorithm presented the highest R² score of 0.987 with the lowest root mean square error (RMSE = 0.044) for the water flux modeling, and extreme gradient boosting (XGB) algorithm exhibited the best results (R² = 0.97; RMSE = 0.234) in the TDS modeling. The Shapley Additive exPlanations (SHAP) analysis found that the phosphorus concentration was a critical input feature for both water flux and TDS modeling. Finally, the selected ML models were used to predict water flux and salinity affected by two input features and the predication results confirmed the importance of the phosphate concentration. The results of this study have demonstrated the promise of ML modeling for investigating OMBR systems.

Engineering pressure retarded osmosis membrane bioreactor (PRO-MBR) for simultaneous water and energy recovery from municipal wastewater

Osmotic membrane bioreactors (OMBR) have gained increasing interest in wastewater treatment and reclamation due to their high product water quality and fouling resistance. However, high energy consumption (mostly by draw solution recovery) restricted the wider application of OMBR. Herein, we propose a novel pressure retarded osmosis membrane bioreactor (PRO-MBR) for improving the economic feasibility. In comparison with conventional FO-MBR, PRO-MBR exhibited similar excellent contaminants removal performance and comparable water flux. More importantly, a considerable amount of energy can be recovered by PRO-MBR (4.1 kWh/100 m²·d), as a result of which, 10.02% of the specific energy consumption (SEC) for water recovery was reduced as compared with FO-MBR (from 1.42 kWh/m³ to 1.28 kWh/m³). Membrane orientation largely determined the performance of PRO-MBR, higher power density was achieved in AL-DS orientation (peak value of 3.4 W/m²) than that in AL-FS orientation (peak value of 1.4 W/m²). However, PRO-MBR suffered more severe and complex membrane fouling when operated in AL-DS orientation, because the porous support layer was facing sludge mixed liquor. Further investigation revealed fouling was mostly reversible for PRO-MBR, it exhibited similar flux recoverability (92.4%) to that in FO-MBR (95.1%) after osmotic backwash. Nevertheless, flux decline due to membrane fouling is still a restricting factor to power generation of PRO-MBR, its power density was decreased by 38.2% in the first 60 min due to the formation of fouling. Overall, in perspective of technoeconomic feasibility, the PRO-MBR demonstrates better potential than FO-MBR in wastewater treatment and reclamation and deserves more research attention in the future.

Mutual effects of CO2 absorption and H2-mediated electromethanogenesis triggering efficient biogas upgrading

Anaerobic digestion coupled with bioelectrochemical system (BES) is a promising approach for biogas upgrading with low energy input. However, the alkalinity generation from electromethanogenesis is invariably ignored which could serve as a potential assistant for CO₂ removal through the transformation into dissolved inorganic carbon (DIC). Herein, a novel bioelectrochemical CO₂ conversion in the methanogenic BES was proposed based on active CO₂ capture and in-situ microbial utilization. It was found that the BES using a stainless steel/carbon felt hybrid biocathode (BES-SSCF reactor) achieved a CH₄ yield of 0.33 ± 0.03 LCH₄/gCOD_removal and increased CH₄ production rate by 28.3% of BES-CF reactor at 1.0 V applied voltage. As the experiment progressed, CH₄ content increased to 93.1% and CO₂ content in the upgraded biogas maintained at below 3%. The continuous proton consumption from H₂ evolution reaction in the hybrid biocathode was capable of creating a slightly alkaline condition in the BES-SSCF reactor and thereby the CO₂ capture as bicarbonate was enhanced through endogenous alkalinity absorption. Microbial community analysis revealed that significant enrichment of Methanobacterium and Methanosarcina at the BES-SSCF cathodic biofilm was favorable for bicarbonate reduction into CH₄ via establishment of H₂-mediated electron transfer. Consequently, the remained CO₂ and DIC only accounted for 12% of total carbon in the BES-SSCF reactor and the high conversion rate of CO₂ to CH₄ (82.3%) was achieved. These results unraveled an innovative CO₂ utilization mechanism integrating CO₂ absorption with H₂-mediated electromethanogenesis.

Forward osmosis treatment of algal-rich water: Characteristics and mechanism of membrane fouling

Membrane fouling is an inevitable problem in forward osmosis (FO) treatment of algal-rich water (ARW). Natural ARW has a complex composition. Therefore, the coexisting components (Ca²⁺, natural organic humic acid [HA], and inorganic particulate kaolinite) in the influence of ARW on FO membrane fouling were studied. The analysis of extended Derjaguin-Landau-Verwey-Overbeek theory and the confocal laser scanning microscopy revealed that the addition of coexisting components increased the attraction between pollutants and membranes, as well as among pollutants to varying degrees, and promoted the development of membrane fouling. Furthermore, Ca²⁺ and HA aggravated irreversible membrane fouling. All coexisting components changed the distribution and thickness of the fouling layer, and the addition of Ca²⁺ increased the content of extracellular organic matter (proteins and polysaccharides). The present results enhance the understanding of the mechanism through which natural ingredients affect microalgal membrane fouling and provide a basis for membrane fouling control to treat ARW.

Impacts of applied voltage on forward osmosis process harvesting microalgae: Filtration behaviors and lipid extraction efficiency

Microalgae are promising source of biofuels, while harvesting process is the obstacle for the further development. Herein, a treatment system that combined electrochemical process with forward osmosis (FO) membrane filtration process was developed to achieve microalgae harvesting. The conductive FO membranes were used as both electrode materials and basic separation system. With -5 V electric field being applied, 57.6% of reduction in water flux loss was observed, while microalgae recovery efficiency increased by 17.3%. The lipid content also increased to nearly 38%. Meanwhile, the inevitable reverse diffusion of solutes in the FO process and the concentration process of the microalgae solution increased the salinity of the microalgae solution, which is generally regarded as an obstacle for the application of FO. However, in the electrically-assisted FO system, it not only improved the efficiency of the electrochemical process, but also can increase the lipid content. The lipid extraction efficiency of the -5 V electric field increased from 17.7% and 28.5% to 20.4% and 31.1%, respectively, with one and two times extractions. The synergistic effect of the reverse diffusion of Cl^- and electrochemical process was conducive for the improvement of the lipid extraction efficiency, and is expected to reduce the energy consumption of the lipid extraction process.

Fouling behaviors are different at various negative potentials in electrochemical anaerobic membrane bioreactors with conductive ceramic membranes

Membrane fouling remains a critical challenge to the practical application of anaerobic membrane bioreactor (AnMBR). To address this challenge, a conductive ceramic membrane was prepared for fouling control in AnMBR. By using the conductive membranes, the anti-fouling performances were enhanced about 3 times at potentials below -1.0 V vs Ag/AgCl compared to the conventional AnMBR. The particle size distributions and the electric field calculations suggest that such an enhancement was mainly attributed to the increased particle sizes of foulants in the supernatant and the electric field forces. Moreover, the scanning electron microscope and confocal laser scanning microscope results show that the conductive membrane at -1.0 V could increase the porosity of the gel layer on the surface, whereas the conductive membrane at -2.0 V could inhibit the activity of adhering bacteria. Surprisingly, membrane fouling of electrically-assisted AnMBR (AnEMBR) at -0.5 V was increased, which was attributed to a dense biofilm-like structure formation. Such a result is contrary to the conventional cognition that negative potential could mitigate the membrane fouling. Overall, this work supplements the understanding of the anti-fouling effects of the electric field in AnEMBR, and provides supplementary information for the engineering application of AnEMBR.