Engineering polydopamine-glued sandwich-like nanocomposites with antifouling and antibacterial properties for the development of advanced mixed matrix membranes

An Assessment of the Catalytic and Adsorptive Performances of Cellulose Acetate-Based Composite Membranes for Oil/Water Emulsion Separation

Cellulose acetate (CA) mixed-matrix membranes incorporating polyvinylpyrrolidone (PVP), bentonite (B or Ben), graphene oxide (GO), and titanium dioxide (TiO2) were prepared by the phase inversion separation technique for oil/water separation. An investigation was performed where the mixed-matrix membrane was tested for the separation performance of hydrophilic and hydrophobic surface properties. An ultrafiltration experiment at the laboratory scale was used to test dead-end ultrafiltration models developed for the treatment performances of oily wastewater under dynamic full-scale operating conditions. Artificial oily wastewater solutions were prepared from hexane, toluene, and engine oil with Tween80 emulsions for oil removal treatment using composite membranes. The impacts of material hydrophilicity, weight loss, permeability, and pore size were investigated, and it was found that the oil retention of membranes with larger pore sizes enabled much more sophisticated water flux. The CA-GO-, CA-B-, and CA-TiO2-incorporated membranes achieved pure water flux (PWF) values of 45.19, 53.41, and 100.25 L/m2h, respectively. The performance of CA-TiO2 in oil/water emulsion rejection was assessed, and the rejection of engine oil/water, toluene/water, and hexane/water mixtures was determined to be 95.21%, 90.33%, and 92.4%, respectively. The CA-based mixed-matrix membrane portrayed better antifouling properties due to enhanced hydrophilicity and water molecules. The CA-TiO2-incorporated membrane possessed the potential to provide high separation efficiency for oily wastewater treatment. This study demonstrates the potential of fine-tuning membrane performances through material hybridization to achieve efficient wastewater treatment.

Silver and Antimicrobial Polymer Nanocomplexes to Enhance Biocidal Effects

Antimicrobial resistance has become a major problem over the years and threatens to remain in the future, at least until a solution is found. Silver nanoparticles (Ag-NPs) and antimicrobial polymers (APs) are known for their antimicrobial properties and can be considered an alternative approach to fighting resistant microorganisms. Hence, the main goal of this research is to shed some light on the antimicrobial properties of Ag-NPs and APs (chitosan (CH), poly-L-lysine (PLL), ε-poly-L-lysine (ε-PLL), and dopamine (DA)) when used alone and complexed to explore the potential enhancement of the antimicrobial effect of the combination Ag-NPs + Aps. The resultant nanocomplexes were chemically and morphologically characterized by UV-visible spectra, zeta potential, transmission electron microscopy, and Fourier-transform infrared spectroscopy. Moreover, the Ag-NPs, APs, and Ag-NPs + APs nanocomplexes were tested against Gram-positive Staphylococcus aureus (S. aureus) and the Gram-negative Escherichia coli (E. coli) bacteria, as well as the fungi Candida albicans (C. albicans). Overall, the antimicrobial results showed potentiation of the activity of the nanocomplexes with a focus on C. albicans. For the biofilm eradication ability, Ag-NPs and Ag-NPs + DA were able to significantly remove S. aureus preformed biofilm, and Ag-NPs + CH were able to significantly destroy C. albicans biofilm, with both performing better than Ag-NPs alone. Overall, we have proven the successful conjugation of Ag-NPs and APs, with some of these formulations showing potential to be further investigated for the treatment of microbial infections.

Surface Mineralization of the TiO2-SiO2/PES Composite Membrane with Outstanding Separation Property via Facile Vapor-Ventilated In Situ Chemical Deposition

Conventional polymeric membranes are broadly employed in water treatment processes; however, most of them suffer from relatively low water permeance and severe membrane fouling phenomena owing to their relatively hydrophobic nature. In this work, a novel class of inorganic-organic composite membranes was developed through a newly developed vapor-ventilated in situ chemical deposition method, where the Ti and Si precursors were first hydrolyzed and then conferred into metal oxides to form a continuous TiO₂-SiO₂ modification layer. Owing to the distinct physicochemical properties, the Ti and Si precursors were leveraged as quasi-molecular regulators to tune the membrane surface chemistry and pore aperture (within the nanoscale) to benefit highly efficient water purification by underpinning the rapid transport of water molecules and featuring an excellent fouling-resistant and fouling-releasing property against typical pollutants. The as-developed TiO₂-SiO₂/PES composite membrane showed a high water permeance of 187.4 L·m^-2·h^-1·bar^-1, together with a relatively small mean pore aperture of 4.2 nm, showing an outstanding permeating efficiency among state-of-the-art membranes with a similar separation accuracy. This study provides a paradigm shift in membrane materials that could open avenues for developing high-performance inorganic-organic composite membranes for complex wastewater treatment.

Highly-efficient PVDF adsorptive membrane filtration based on chitosan@CNTs-COOH simultaneous removal of anionic and cationic dyes

An adsorptive membrane filtration based on polyvinylidene fluoride (PVDF) with chitosan (CS) and carboxylated carbon nanotubes (CNTs-COOH) is prepared by method of phase conversion, and the PVDF-CS@CNTs-COOH membranes can effectively separate anionic and cationic dye wastewater. Compared to pure PVDF membranes, PVDF-CS@CNTs-COOH increases pure water flux from 36.39 (L·m^-2·h^-1) to 85.25 (L·m^-2·h^-1), an increase of nearly 230%. The membrane exhibits excellent rejection performance in the filtration of six types of dye wastewater. The modified membranes also performed well in terms of rejection of mixed anionic and cationic dyes and also have a high performance in recycling, with a flux of over 94% for both anionic and cationic dyes. In addition, the adsorption curve fitting results showed that the adsorption process was more consistent with the pseudo-second-order adsorption kinetic model and Langmuir mode.

A mini review of multifunctional ultrafiltration membranes for wastewater decontamination: Additional functions of adsorption and catalytic oxidation

Multifunctional ultrafiltration membranes, which achieve ultrafiltration and additional functions in one unit, are a new strategy developed in recent years for wastewater treatment. In this mini review, we summarized and commented on the development of adsorptive and catalytically oxidative multifunctional ultrafiltration membranes, as well as pointed out possible further trends. The main methods for membrane preparation, i.e., blending, surface coating, reverse filtration, etc., were summarized, and the advantages and disadvantages of each method were discussed. In addition, the key criteria which influence the performance of membranes, including the efficiency of additional functions, original ultrafiltration, permeance, and stability, were analyzed. Furthermore, we introduced the applications of different classes of multifunctional ultrafiltration membranes, and tried to further analyzed some examples of multifunctional ultrafiltration membranes used for adsorption and catalytic oxidation. The most significant advantage of this technology is the high efficiency for the simultaneous removal of different kinds of pollutants or for the removal of one kind of pollutant during the deep treatment of multicomponent wastewater. However, some challenges still oppose the practical application of multifunctional ultrafiltration. We believe that breaking the trade-off between the high efficiency of additional functions and high flux, strengthening the stability of the membranes, achieving synergistic effects between multi-effect functions, and investigating the interaction mechanisms between active materials and the membrane are key points for further research.

Antifouling and antibacterial behavior of membranes containing quaternary ammonium and zwitterionic polymers

To overcome the organic-/bio- fouling of the membrane, a dual-functional ultrafiltration membrane containing quaternary ammonium and zwitterionic polymers via quaternization and surface radical polymerization was designed, and its antifouling and antibacterial behavior was studied. In this work, poly(vinylidene fluoride)/poly(methyl methacrylate-co-dimethylamino-2-ethyl methacrylate) (PVDF/P(MMA-co-DMAEMA)) blend membrane was quaternized by p-chloromethyl styrene (p-CMS), and the double bonds were introduced onto the membrane surface, which further participated in the polymerization of zwitterionic monomers on the membrane surface. The results indicated that the resultant membrane exhibited obviously improved hydrophilicity and weak positive charge (isoelectric point, 7.49). The membrane presented higher flux recovery ratio and lower protein adhesion compared with the pure PVDF membrane. Meanwhile, the membrane showed high-efficiency broad-spectrum antibacterial performance, that is, the bacteria killing efficiency of S. aureus and E. coli reached 98.2% and 97.0%, respectively. Moreover, the membrane effectively inhibited bacterial adhesion, which is important for the long-term antibacterial properties of membrane. This antifouling and antibacterial PVDF membrane may have potential in the long-term filtration process, especially when dealing with microbiologically contaminated water.