Influence of alveolar bone loss, post type, and ferrule presence on the biomechanical behavior of endodontically treated maxillary canines: Strain measurement and stress distribution

Short fiber-reinforced composite resins as post-and-core materials for endodontically treated teeth: A systematic review and meta-analysis of in vitro studies

STATEMENT OF PROBLEM

As the use of traditional posts has been associated with complications and failure outcomes, the introduction of novel materials and minimally invasive dentistry has shifted toward the use of composite resin post-and-core restorations for endodontically treated teeth. As a further process, to improve stress absorption environment in restored teeth, the invention of short fiber-reinforced composite resins (SFRCs) as post-and-core restorations has recently emerged. However, evidence regarding its performance is still scarce, and a synthesis of existing data is lacking.

PURPOSE

The purpose of this systematic review and meta-analysis was to assess the performance of SFRC post-and-core restorations, regarding fracture resistance and failure mode and considering both cyclic and static loading.

MATERIAL AND METHODS

An electronic search in 5 databases was conducted up to August 2022, and the protocol of the study was registered a priori. The search terms included "fiber reinforced composite," "core build-up," and "post." Studies were considered if they compared SFRC restorations with other types of conventional posts and teeth restored using bulk fill composite resin. The internal validity of the studies was assessed by using a custom-made risk of bias tool.

RESULTS

A total of 1271 records were identified, of which 13 were considered for full-text assessment. Eight were ultimately included, all being in vitro studies, and 7 of them were deemed eligible for quantitative syntheses. The results varied considerably across studies with divergent fracture resistance values and percentages of catastrophic failure being reported. Standard depth (6 mm) SFRCs presented fewer repetitions until fracture on average, compared with the individually made FRCs (3 studies: mean difference (MD): -4062; 95% CI: -6148, -1975; P<.001) under cyclic loading. Under static loading, SFRCs (standard depth) presented a nearly 300 N lower fracture force compared with that of intact teeth, (3 studies: MD: -297; 95%CI: -378, -216; P<.001).

CONCLUSIONS

Evidence on the laboratory fracture and failure performance of SFRCs is limited, and future studies should incorporate more standardized experimental conditions, as well as SFRCs with limited sacrifice of tooth substrate within the root canal of endodontically treated teeth.

Effect of apical root resection, orthodontic extrusion, and surgical crown lengthening on load capability

OBJECTIVES

This study aims to investigate the load-to-fracture of procedures changing crown-to-root ratio (RCRR) aimed to restore severely damaged upper central incisors to avoid tooth extraction compared to implant placement. There is no evidence on load capability after apical root resection (AR), orthodontic extrusion (OE), and surgical crown lengthening (SCL) in respect to RCRR, respectively.

MATERIAL AND METHODS

Human maxillary central incisors were endodontically treated, decoronated, and divided into 4 groups (n = 48). The following specimen preparation was performed: (I) adhesive core-and-post build-up (control), (II) as (I) and 2 mm apical root resection (AR), (III) before adhesive core-and-post build-up teeth were shortened 2 mm coronally (OE) (IV) as (I), but specimens were embedded 4 mm instead of 2 mm below the CEJ (SCL), group (V) implant-borne restoration with individual all-ceramic abutments (n = 12; ∅4.1/l = 12 mm) (IBR). All specimens received all-ceramic crowns, thermo-mechanical (TML), and subsequent linear loading (LL) until failure. RCRR were calculated and log-rank, Kruskal-Wallis, Mann-Whitney U, ANOVA, and chi-square tests applied (p = 0.05).

RESULTS

Fracture loads after subsequent LL differed significantly (p = 0.001) between groups, while implants showed the highest values. Fmax median (min/max) were as follows: (I) 252 (204/542), (II) 293 (243/443), (III) 253 (183/371), (IV) 195 (140/274), and (V) 446 (370/539). Pair-wise comparison showed significant differences (p = 0.001) between group I/IV and group V, I, and IV (p = 0.045), II and IV (p = 0.001), and III compared to IV (p = 0.033), respectively. RCRR below 1 significantly increased load capability compared to RCRR = 1.

CONCLUSIONS

OE appears to preferably ensure biomechanical stability of teeth that are endodontically treated and receive core-and-post and crown placement compared to SCL. AR has no adverse biomechanical impact. RCRR < 1 is biomechanically beneficial.

CLINICAL RELEVANCE

For endodontically treated and restored teeth, orthodontic extrusion should be preferred compared to surgical crown lengthening prior single-crown restoration. As orthodontic extrusion, apical root resection has no adverse effect on load capability. Single-crown implant-borne restorations are most load capable.

Finite element analysis of endodontically treated premolars without ferrule restored with one-piece glass fiber post and core in combination with different inner shoulder retention form systems

OBJECTIVE

The current study was performed to explore the impact of post materials as well as the inner shoulder retention form (ISRF) design on the biomechanical behavior of endodontically treated premolars without ferrule restoration using a method of mathematical three-dimensional (3D) finite element analysis (FEA).

METHODS

Based on the tooth anatomy and our previous research, eight mandibular second premolar FEA models representing different restorative situations were built: teeth with (a) 2.0 mm height ferrule (DF), (b) no ferrule (NF), (c) 0.5 mm width and 0.5 mm depth ISRF (ISRFW0.5D0.5), (d) 0.5 mm width and 1.0 mm depth ISRF (ISRFW0.5D1.0), (e) 0.5 mm width and 1.5 mm depth ISRF (ISRFW0.5D1.5), (f) 1.0 mm width and 0.5 mm depth ISRF (ISRFW1.0D0.5), (g) 1.0 mm width and 1.0 mm depth ISRF (ISRFW1.0D1.0), (h) 1.0 mm width and 1.5 mm depth ISRF (ISRFW1.0D1.5). All groups were restored with prefabricated glass fiber post and resin composite core (PGF), one-piece glass fiber post-and-core (OGF) and cast Co-Cr alloy (Co-Cr) respectively, and the zirconia crown was restored. Load (180N) was subjected to the buccal cusp at 45° to the tooth's long axis. Stress pattern, maximum principal stress values (MPS), and maximum displacement values on root, post and core, cement layer were calculated for each model.

RESULTS

Stress distributions were similar while the values were different among groups. Regardless of restorative approaches, roots restored with PGF showed the highest MPS values, followed by OGF and Co-Cr groups. Regardless of post materials, NF groups resulted in the highest MPS values and maximum displacement values, while ISRF and DF groups exhibited similar results. Compared with PGF groups in association with ISRF, except for OGF with ISRFW0.5D0.5, the remaining OGF groups with ISRF and all Co-Cr groups in association with ISRF presented lower values than that of DF groups. And among different ISRF systems, roots restored with ISRFW1.0D1.0 presented the lowest stress (PGF: 32.96 MPa, OGF: 31.69 MPa, Co-Cr: 29.66 MPa).

CONCLUSIONS

For endodontically treated premolars without ferrule, restored with OGF in combination with ISRF preparation could effectively enhanced its load-bearing capacity. Furthermore, the ISRF with a depth and width of 1.0 mm is recommended.

Finite element analysis of maxillary first molar with mesial-occlusal-distal-palatal defect restored with different post-and-core strategies

Purpose

To explore which restoration strategy generates the most favorable stress distribution in an endodontically-treated maxillary first molar with mesial-occlusal-distal-palatal defect.

Methods

Models with one post in palatal canal (PP), each post in palatal and distobuccal canals (PDP), each post in palatal and mesiobuccal canals (PMP), and each post in all canals (PDMP) were established for an endodontically-treated maxillary first molar with mesial-occlusal-distal-palatal defect either with fiber-reinforced composite (FRC) post or gold alloy cast (GAC) post. A 400-N vertical force and a 225-N lateral force were respectively applied. The Mohr-Coulomb stress ratio (σ_{MC ratio}) in the residual tooth structure (RTS), the resin cement, and the crowns, the tensile stress (σ_t) and compressive stress (σ_c) in the FRC posts, the von-Mises stress ratio (σ_{vM ratio}) in the GAC post-and-cores, and the σ_t and shear stress (σ_s) at the adhesive interfaces were calculated using finite element analysis.

Results

FRC posts generated lower σ_{MC ratio} than GAC posts in the RTS (0.3274-0.3643 vs. 0.3399-0.4118). Among the FRC post groups, the PDMP group got the lowest σ_s at the dentin-post interface (14.92 MPa) and the abutment-crown interface (8.242 MPa) under vertical loading, as well as the lowest σ_{MC ratio} in the RTS (0.3381) and the lowest σ_s at the dentin-post interface (38.00 MPa) under lateral loading.

Conclusions

From the point of stress distribution, placing FRC posts in the palatal, distobuccal, and mesiobuccal canals is the optimal strategy in restoring a severely damaged maxillary first molar, provided that lateral occlusal force is reduced.

Endocrown fixed partial denture: Is it possible?

STATEMENT OF PROBLEM

Whether the replacement of a missing tooth with a fixed partial denture supported by an endodontically treated abutment could be improved with endocrowns is unclear.

PURPOSE

The purpose of the study was to evaluate the mechanical behavior of a fixed partial denture (FPD) according to the preparation of the abutment teeth (endocrown or complete crown) in terms of stress magnitude in the prosthesis, cement layer, and tooth.

MATERIAL AND METHODS

A posterior model with 2 abutment teeth (first molar and first premolar) was modeled with a computer-aided design (CAD) software program for conducting a 3-dimensional finite element analysis (FEA). To replace the missing second premolar, the model was replicated in different possible FPDs according to the abutment preparation design (complete crown [Conventional], 2 endocrowns [EC]) or an endocrown on one of the abutment teeth (first molar [ECM] and first premolar [ECP]) for a total of 4 designs. All FPDs were in lithium disilicate. The solids were imported to an analysis software program (ANSYS 19.2) in the standard for the exchange of product data (STEP) format. The mechanical properties were considered isotropic and the materials to show linear elastic and homogeneous behavior. An axial load (300 N) was applied at the occlusal surface of the pontic. The results were evaluated by colorimetric stress maps of von Mises and maximum principal stress in the prosthesis, maximum principal stress and shear stresses on the cement layer, and maximum principal stress in the abutment teeth.

RESULTS

The von Mises stresses revealed that all FPD designs behaved similarly and that, considering the maximum principal stress criteria, the pontic was the most stressed region. For the cement layer, the combined designs presented an intermediate behavior, with the ECM more suitable to reducing the stress peak. The conventional preparation allowed less stress concentration in both teeth, and higher stress concentration in the premolar was observed with an endocrown. The endocrown decreased the risk of fracture failure. Considering the risk of debonding failure for the prosthesis, the endocrown preparation was only able to decrease the failure risk when the EC design was used and when only the shear stress was considered.

CONCLUSIONS

Performing endocrown preparations to retain a 3-unit lithium disilicate FPD is an alternative to conventional complete crown preparations.

Effects of composite resin core level and periodontal pocket depth on crack propagation in endodontically treated teeth: An extended finite element method study

STATEMENT OF PROBLEM

Preserving teeth with radicular cracks with or without a periodontal pocket is an alternative to extraction. However, an effective protocol for the restoration of radicular cracks is lacking.

PURPOSE

The purpose of this study was to examine the composite resin core level and periodontal pocket depth effects on stress distribution, maximum von Mises stress, and crack propagation in endodontically treated teeth by using the extended finite element (FE) method.

MATERIAL AND METHODS

Four 3-dimensional models of a cracked endodontically treated mandibular first molar were constructed: PP2C2 (periodontal pocket depth, 2 mm; composite resin core level, 2 mm below the canal orifice level); PP2C4 (periodontal pocket depth, 2 mm; composite resin core level, 2 mm below the crack level); PP4C2 (periodontal pocket depth, 4 mm; composite resin core level, 2 mm below the canal orifice level); and PP4C4 (periodontal pocket depth, 4 mm; composite resin core level, 2 mm below the crack level). The crack initiation was at the same level in all models. A static 700-N load was applied to the models in a vertical direction.

RESULTS

The highest stress in dentin was observed in PP2C2, whereas PP2C4 exhibited the lowest stress and least crack propagation. Stress was high in the dentin and supporting bone. No reduction in crack propagation was observed in the PP4 models, regardless of the composite resin core level.

CONCLUSIONS

The periodontal pocket depth (2 mm and 4 mm) and composite resin core level (2 mm below the crack level and 2 mm below the canal orifice level) affected stress concentration in dentin, resulting in different patterns of crack propagation in the FE models.

Effect of bone defect width and a ferrule on the fracture characteristics of vertically fractured teeth reattached with adhesive resin cement: An in vitro study

This study aimed to clarify the effects of vertical bone defect width and a ferrule on fracture of the fragments of fractured tooth reattached with adhesive resin cement (reattached tooth). The reattached tooth was built up by a fiber post and composite resin core for abutment and formed to the abutment with or without a ferrule. The vertical bone defect was fabricated with a V-shaped defect in different widths. The fracture load was evaluated using a universal testing machine. The vertical bone defect did not affect the fracture load, but a ferrule increased the root fracture load. For the specimens without a ferrule, debonding between the composite resin core and the root at the coronal loading side and fractures at the apical side of the root were found. In conclusion, the ferrule at abutment could affect fracture load and modes, and the bone defect width did not.

Effect of Different Ceramic Materials on Fatigue Resistance and Stress Distribution in Upper Canines with Palatal Veneers

OBJECTIVE

 The aim of this study was to evaluate, by means of a fatigue life test, different ceramic materials used in palatal veneers to restore the canine guidance.

MATERIALS AND METHODS

 Forty-five standardized anatomical preparations were made in extracted healthy human canines with 1.2 uniform thickness. Samples were scanned, restorations were designed and milled in polymer-infiltrated ceramic network (PICN, Vita Enamic), zirconia-reinforced lithium silicate (ZLS, Vita Suprinity), and high translucent yttrium oxide-stabilized tetragonal zirconia (YZHT, Vita YZHT). Dental preparations were etched, restorations were processed according to the manufacturers' recommendations, and adhesively cemented. Then, three samples of each group were tested with load-to-fracture to determine the fatigue parameters. In addition, the palatal veneers stresses were evaluated using numerical models through finite element analysis.

RESULTS

 The mean of the monotonic test for PICN, ZLS, and YZHT was 674.18 N, 560.5 N, and 918.98 N, respectively. The StepWise test was performed until specimen fracture or until suspension of the test after 1.2 × 10⁶ cycles. Regarding survival, using the Kaplan-Meier method, PICN presented results for the mean and median of 245.21 N and 225 N, respectively; ZLS had an average of 175.76 N and a median of 168 N, and YZHT with an average of 383.30 N and a median of 366 N. Regarding the Weibull method, PICN showed results of 5.43 β and 264 η for form and scale, respectively; ZLS had 36.14 β for form and 380.67 η for scale; and YZHT presented 4.95 β for form and 417.38 η for scale. The highest stress value was calculated for YZHT, ZLS, and PICN, respectively.

CONCLUSIONS

 It was possible to conclude that all tested materials have the possibility of being used for rehabilitation of upper canines' palatal surface.

Biomechanical behavior of endocrown restorations with different cavity design and CAD-CAM materials under a static and vertical load: A finite element analysis

STATEMENT OF PROBLEM

The influence of different restorative materials, the divergence angle, and the preparation design of the pulp chamber floor in endocrowns on stress distribution is unclear.

PURPOSE

The purpose of this finite element analysis study was to evaluate the stress distribution and maximum von Mises stress values in endocrown restorations and remaining teeth.

MATERIAL AND METHODS

An endodontically treated first mandibular molar was prepared with 2-mm occlusal reduction, a butt-joint margin, and a mesial box with a 4-mm buccolingual extension to receive an endocrown restoration. The model was then scanned, and the exported standard tessellation language file was designed according to the anatomic references by using a computer-aided design software program. The reference model was duplicated, and 27 variations were formed: restorations made of IPS e.max, Vitablocs MarkII, and Vita Enamic, as well as different divergence angles of 6, 12, and 16 degrees prepared with 3 variations of pulp chamber floor designs, keeping the natural form, adding a 1-mm glass ionomer pulp chamber base, and adding a 2-mm extension into the distal canal. Stress distribution under axial loading and maximum von Mises stress values were analyzed and calculated by using the Ansys software program.

RESULTS

Endocrown restoration presented the lowest von Mises stress values when a 6-degree divergence angle was used with Vitablocs MarkII. However, in other layers such as enamel, resin cement, and pulpal floor, the lowest von Mises stress values were observed in IPS e.max restorative material when the divergence angle was increased to 16 degrees. No difference was found in the stress distribution pattern and maximum von Mises stress values in the alveolar bone or periodontal ligament.

CONCLUSIONS

Endocrowns fabricated with lithium disilicate ceramics without intraradicular extension exhibited lower stresses on tooth structure. An increase in the divergence angle improved the stress distribution on tooth structure; however, sound dental tissue should not be removed to achieve better stress distribution.

The effect of fiber insertion on fracture strength and fracture modes in endocrown and overlay restorations

Aim of this study was to determine the fracture strength and modes of endocrown and overlay restorations with/without fiber reinforcement on endodontically treated teeth. Sixty-five molar teeth were used: Group IN (intact teeth), Group E (endocrown), Group ER (endocrown + ribbond), Group O (overlay), Group OR (overlay + ribbond; n = 13). Ribbond (Seattle, WA) was inserted at the base of pulp chamber in Group ER and OR. All restorations were designed and produced by using computer-aided design and computer-aided manufacturing (Sirona Dental Systems, Bensheim, Germany) and Cerasmart (GC Corp. Kasugai, Aichi, Japan). All teeth were subjected to thermomechanical aging and fractured in a universal test device. Fractured surfaces were analyzed with a stereomicroscope (SMZ1000, Nikon, Japan). Data were analyzed with Welch's analysis of variance and Games-Howell test (p < .001). Group E showed significantly lower fracture strength values than other groups(p < .05). No statistically significant differences were found among the other groups(p > .05). Most of the unfavorable fractures were seen in Groups E and O. Overlay restorations showed higher fracture strength values than endocrown restorations. Although fiber insertion did not improve the fracture strength of the indirect restorations, it reduced the frequency of irreparable fracture mode. Overlay restorations and fiber application are more advantageous in preserving the durability of the endodontically treated teeth.

Better Glass-fiber Post Preservation in Teeth with Ferrule When Subjected to Chewing

OBJECTIVES

To evaluate the influence of ferrule effect and mechanical fatigue aging on glass-fiber post push-out bond strength (PBS) to root-canal dentin at different root thirds of premolars.

METHODS AND MATERIALS

Thirty-two sound maxillary premolar teeth were collected, and randomly assigned to two experimental groups (n=16): 'Remaining Dentin Ferrule' (RDF) = coronal crown cut 2.0 mm above the cementoenamel junction (CEJ); 'Without Dentin Ferrule' (WDF) = coronal crown cut at the cemento-enamel junction. Teeth were endodontically treated, post spaces were prepared up to 10.0-mm depth from CEJ, and glass-fiber posts were cemented using a dual-cure self-adhesive composite cement. Standardized cores were built using a light-cure composite, upon which tooth cores were prepared using a 1.5-mm taper ogival-end diamond bur. Crowns were handmade using self-cure acrylic resin and cemented using the aforementioned composite cement. Half of the specimens were subjected to 1,200,000 cycles of mechanical fatigue in a chewing simulator (F = 'Fatigue'), while the other half were stored in distilled water at 37°C for 1 week (C = 'Control'). All specimens were horizontally sectioned into 1.0-mm thick slices prior to PBS test; the failure modes were assessed using stereomicroscopy and scanning electron microscopy (SEM). Data were analyzed for each root third using two-way analysis of variance (ANOVA) followed by Tukey HSD post-hoc test; frequency distribution was compared by Chi-square test (α=0.05) and post-hoc comparisons with Bonferroni.

RESULTS

The mean PBS in MPa (SD) were = RDF_F = 10.4 (2.9); WDF_F = 6.9 (1.7); RDF_C = 14.5 (2.7); WDF_C = 14.2 (2.9). Similar PBS were found for the root thirds. For all root thirds, significant differences were found for both the factors Dentin Ferrule and Fatigue, and their interaction (p<0.05). The lowest PBS was found for specimens without dentin ferrule subjected to chewing fatigue (p<0.001). Most failures occurred at the composite cement/dentin interface, followed by mixed and composite cement/glass-fiber post interfacial failures. There was a significant increase in mixed failures for the WDF_F group (p<0.001).

CONCLUSION

Absence of 2.0-mm remaining dentin ferrule in premolars resulted in a higher decrease of the glass-fiber posts' PBS to dentin after mechanical fatigue, irrespective of root third.

Minimal tooth preparation for posterior monolithic ceramic crowns: Effect on the mechanical behavior, reliability and translucency

OBJECTIVE

Despite the increased use of monolithic crowns, their performance has yet to be determined when the minimal tooth preparation (MTP) principle is considered. The goal of this study was to evaluate the effect of MTP on the mechanical behavior, reliability and translucency of posterior monolithic ceramic crowns.

METHODS

Dentin analogues were machined using two preparation designs (0.5 or 1 mm reduction) to receive first molar crowns in order to evaluate the monolithic crown performance. Next, 126 crowns were divided (21/g) according to the material (High translucent zirconia - YZHT, Zirconia reinforced lithium silicate - ZLS and Hybrid ceramic - HC) and thickness (0.5 or 1 mm). Tensile stress concentration was calculated using the finite element method. The crowns were adhesivelly cemented and step stress fatigued to calculate reliability for missions at 600 and 1000 N. Translucency was analyzed in 10 discs of each material and thickness.

RESULTS

Higher stress concentration was found in thinner crowns and those with higher elastic modulus. YZHT crowns were suspended when fatigue reached 1500 N load, thus 1-parameter Weibull was used to analyze the data. Reliability was only affected by thickness at 1000 N. ZLS.5 showed lower survival than HC.5, which was similar to the groups that presented 100% survival. YZHT showed the highest strength and data scattering. ZLS1 (22.3 ± 1.4) presented higher translucency than HC1 (19.2 ± 0.6) and YZHT1 (12.0 ± 2.9), whereas ZLS.5 and HC.5 were similar to each other (26.5 ± 2.3, 26.7 ± 2.2) and superior to YZHT.5 (12.7 ± 1.2).

SIGNIFICANCE

HC.5 combined high reliability and translucency with low stress concentration, yielding better crown performance and tooth preservation.

Effect of different materials and undercut on the removal force and stress distribution in circumferential clasps during direct retainer action in removable partial dentures

OBJECTIVES

This study aimed to evaluate the effect of different materials and undercut on the removal force and stress distribution in the supporting tooth and in the circumferential clasp used in removable partial prosthesis.

METHODS

Upper molars prepared for Akers circumferential clasp with retention and opposing arm were modeled, scanned, elaborated with CAD software and the geometries imported in FEA and analyzed. Six different materials were selected for the clasp (Polyamide, Polyoxymethylene, Polyetheretherketone - PEEK, Gold alloy, Titanium and CoCr) and 3 different undercuts (0.25, 0.50 and 0.75mm), totaling 18 groups.

RESULTS

The clasps presented greater stress in their structure and potentially greater damage to the dental enamel when made with rigid materials and with more undercut; however, they presented greater ability to remain in position.

SIGNIFICANCE

Polyamide with a higher undercut is an esthetic alternative to rigid metallic clasps. It showed promising behavior because it strongly reduces the damage to the enamel, and even with an undercut of 0.75, the retention is lower than for CoCr with a 0.25 undercut, and this retention might still be sufficient. Polyoxymethylene and Polyetheretherketone (PEEK) are not suitable materials for the clasps, because the maximum stress occurring during removal with higher undercuts is higher than the material strength.

An In Vitro Evaluation of Fracture Resistance of Endodontically Treated Maxillary Central Incisor Restored with Custom-Made Cast Post and Core with Uniform and Nonuniform Core Ferrule Heights

Aim

The aim of this study was to evaluate in vitro fracture resistance of endodontically treated teeth restored with custom-made cast post and core having uniform and nonuniform core ferrule heights.

Materials and Methods

Thirty-five freshly extracted human maxillary central incisors were included in this study. All teeth were subjected to standard root canal treatment. The teeth were randomly divided into five groups-Group 1: uniform ferrule (2 mm buccal, lingual, and proximal), Group 2: uniform ferrule (3 mm buccal, lingual, and proximal), Group 3: nonuniform ferrule (2 mm buccal, 3 mm lingual), Group 4: nonuniform ferrule (2 mm buccal, 4 mm lingual), and Group 5: no ferrule. The teeth were sectioned horizontally 4 mm above cementoenamel junction and post space preparation was performed maintaining 4 mm of apical gutta-percha. Ferrule was prepared according to dimension designated for each group. Custom-made cast post and core were fabricated and luted using zinc phosphate cement. Testing was conducted using universal testing machine with application of static load (Newton), and failure load was recorded. Data were analyzed by one-way analysis of variance and Tukey test. The mode of fracture was noted by visual inspection for all specimens.

Result

Significant differences (P < 0.001) were found among mean fracture forces of test groups. Group 1: 1181.66 ± 68.29, Group 2: 1455.58 ± 173.11, Group 3: 1019.00 ± 52.55, Group 4: 971.58 ± 66.52, and Group 5: 888.00 ± 60.56. The presence of nonuniform ferrule height resulted in a significant decrease (P < 0.0001) in mean fracture strength compared to uniform 2- and 3-mm core ferrule height.

Conclusion

The central incisors restored with cast post and core and crowns with 3-mm uniform core ferrule were more fracture resistant compared to central incisors with nonuniform core ferrule height. Both the uniform and nonuniform core ferrule groups were more fracture resistant than the group that lacked ferrule.

Does ferrule thickness influence resistance to fracture of endodontically treated teeth?

Background:

Teeth with severe crown destruction and endodontically treated may or may not present a circular strip of dental tissue located in the cervical region called ferrule.

Aims:

The aims of this study were to evaluate ferrule thickness influence on endodontically treated teeth (ETT) resistance to fracture.

Materials and Methods:

A total of 30 bovine incisor teeth were selected, endodontically treated and randomly distributed, according to the ferrule thickness: G1- no ferrule, G2 – 1 mm, and G3 – 2 mm. All the teeth were restored with prefabricated posts and composite resin. Resistance to fracture was established as the compression strength at 45° tilt at the lingual surface of the crown.

Statistical Analysis Used:

Data were analyzed using ANOVA and Tukey's test.

Results:

Resistance to fracture of G1 and G2 were significantly higher than that of G3 (P < 0.001). The pattern of fracture, common to all groups, occurred at the composite resin on the coronary portions.

Conclusion:

Ferrule thickness can influence the resistance to fracture of ETT.

Impact of endodontic post material on longitudinal changes in interproximal bone level: a randomized controlled pilot trial

OBJECTIVES

Aim was to evaluate the impact of glass fiber versus titanium endodontic posts on the interproximal bone level around severely damaged endodontically treated teeth.

MATERIALS AND METHODS

Thirty-eight participants of a randomized controlled trial on glass fiber (n = 18) and titanium post-endodontic restorations (n = 20) received radiographs at two different times after post placement (T0 = <12 months and T1 = 36-72 months after post placement). A total of 76 radiographs were analyzed with an image-editing software. Medians of changes in mesial and distal interproximal bone level (∆MBL, ∆DBL) were calculated and tested for statistical significance with respect to post material using Mann-Whitney U test (p < 0.05). Impact of post material on bone level changes was assessed in multilevel mixed-effect linear regression models.

RESULTS

The mean observation period was 54 months for glass fiber and 50 months for titanium posts. Interproximal bone loss was small in both groups during the study period with no significant differences between groups (glass-fiber group, ∆MBL = - 0.03 mm and ∆DBL = - 0.06 mm; titanium group, ∆MBL = - 0.07 mm and ∆DBL = - 0.17 mm; both p > 0.05). Overall, impact of post material on bone loss was almost negligible with a nonsignificant difference between materials of 0.10 mm during the entire study period.

CONCLUSION

The rigidity of endodontic post material has no impact on the level of alveolar bone support of severely damaged endodontically treated teeth.

CLINICAL RELEVANCE

Post-endodontic restorations of severely damaged teeth can achieve steady levels of periodontal bone support as a parameter of periodontal health, irrespective of post material.

Failure loads of all-ceramic cantilever fixed dental prostheses on post-restored abutment teeth: influence of the post presence and post position

The influence of a fiber post-restored abutment tooth on the load capability of a three-unit zirconia framework cantilever fixed dental prosthesis (cFDP) was evaluated after simulated clinical function. Human lower sound premolars (n = 64) were distributed, in equal numbers, to four experimental groups: two vital abutment teeth (group I; control); mesial abutment tooth post-restored (group II); distal abutment tooth post-restored (group III); and mesial and distal abutment teeth post-restored (group IV). All specimens received an adhesively luted three-unit cFDP of veneered zirconia. Simulated clinical function was performed by two subsequent sequences of thermal-cycling (2 × 3,000 cycles) and mechanical loading (1.2 × 10⁶ load cycles from 0 to 50 N) (TCML). Four specimens failed during TCML (one in each of groups I and IV and two in group II). The maximum load capability ranged from 365 to 538 N and was not significantly different between groups. Specimens with post-restored abutments failed mainly because of abutment tooth fracture of the distal abutment. The presence or position of post-restored abutment teeth has no significant impact on load capability of all-ceramic three-unit cFDPs. The risk of tooth fracture of the distal abutment teeth of a cFDP was significantly increased when one abutment tooth, irrespective of its position, was post-and-core restored.

Influence of remaining coronal thickness and height on biomechanical behavior of endodontically treated teeth: survival rates, load to fracture and finite element analysis

Objective

To evaluate the effect of restorative strategy (fiber post vs cast post and core), coronal height (0 mm vs 2 mm) and thickness (higher than 1 mm vs lower than 1 mm) on survival rate, fracture resistance and stress distribution.

Material and Methods

Seventy-two bovine teeth were cleaned and allocated in six groups (n = 12). Twenty-four teeth were sectioned at 13 mm length (no remaining coronal structure) and forty-eight were sectioned at 15 mm (2 mm remaining coronal structure). Half of the forty-eight had remaining coronal thickness lower than 1 mm and the other half had thickness higher than 1 mm. All root canals were prepared at 10 mm (luting length), fiber posts were cemented in thirty-six specimens and cast post and core in other thirty-six. All teeth were restored with metallic crowns. Specimens were submitted to 1.5 million cycles (100 N, 45°, 10 Hz at 2 mm below incisal edge) and evaluated at each 500,000 cycles to detect failures. Specimens that survived were submitted to load to fracture test. Bidimensional (Rhinoceros^® 4.0) models were obteined survival data submitted to Kaplan-Meier (α=0.05) analysis and load to fracture values submitted to ANOVA and Tukey tests (α=0.05).

Results

Groups without remaining coronal structure showed survival rates lower than other groups (p=0.001). ANOVA showed higher values of load to fracture for groups with coronal thickness higher than 1 mm (p=0.0043). Finite element analysis showed better stress distribution in groups with remaining coronal structure and restored with fiber post.

Conclusion

Specimens without remaining coronal structure have lower survival rates. Specimens with remaining structure lower than 1 mm and without coronal structure support the same load to fracture value independently of the restorative strategy.

An in vitro study evaluating the effect of ferrule design on the fracture resistance of endodontically treated mandibular premolars after simulated crown lengthening or forced eruption methods

Background

The purpose of this study was to evaluate the effect of ferrule design on the fracture resistance of endodontically treated mandibular first premolars after simulated crown lengthening and orthodontic forced eruption methods restored with a fiber post-and-core system.

Methods

Forty extracted and endodontically treated mandibular first premolars were decoronated to create lingual-to-buccal oblique residual root models, with a 2.0 mm height of the lingual dentine wall coronal to the cemento-enamel junction, and the height of buccal surface at the cemento-enamel junction. The roots were divided randomly into five equal groups. The control group had undergone incomplete ferrule preparation in the cervical root, with 0.0 mm buccal and 2.0 mm lingual ferrule lengths (Group F0). Simulated surgical crown lengthening method provided ferrule preparation of 1.0 mm (Group CL/F1) and 2.0 mm (Group CL/F2) on the buccal surface, with ferrule lengths of 3.0 mm and 4.0 mm on the lingual surface, respectively. Simulated orthodontic forced eruption method provided ferrule preparation of 1.0 mm (Group OE/F1) and 2.0 mm (Group OE/F2) on the buccal surface and ferrule lengths of 3.0 mm and 4.0 mm on the lingual surface, respectively. After restoration with a glass fiber post-and-core system and a cast Co-Cr alloy crown, each specimen was embedded in an acrylic resin block to a height on the root 2.0 mm from the apical surface of the crown margin and loaded to fracture at a 135° angle to its long axis in a universal testing machine. Data were analyzed statistically using two-way ANOVA with Tukey HSD tests and Fisher’s test, with α = 0.05.

Results

Mean fracture loads (kN) for groups F0, CL/F1, CL/F2, OE/F1 and OE/F2 were as follows: 1.01 (S.D. = 0.26), 0.91 (0.29), 0.73 (0.19), 0.96 (0.25) and 0.76 (0.20), respectively. Two-way ANOVA revealed significant differences for the effect of ferrule lengths (P = 0.012) but no differences for the effect of cervical treatment methods (P = 0.699). The teeth with no buccal ferrule preparation in control group F0 had the highest fracture resistance. In contrast, the mean fracture loads for group CL/F2 with a 2.0-mm buccal and 4.0-mm lingual ferrule created by simulated crown lengthening method were lowest (P = 0.036).

Conclusions

Increased apically complete ferrule preparation resulted in decreased fracture resistance of endodontically treated mandibular first premolars, regardless of whether surgical crown lengthening or orthodontic forced eruption methods been used.

3-D finite element analysis of the effects of post location and loading location on stress distribution in root canals of the mandibular 1st molar

Objective

The purpose of this study was to evaluate, by using finite element analysis, the influence of post location and occlusal loading location on the stress distribution pattern inside the root canals of the mandibular 1^st molar.

Material and Methods

Three different 3-D models of the mandibular 1^st molar were established: no post (NP) – a model of endodontic and prosthodontic treatments; mesiobuccal post (MP) – a model of endodontic and prosthodontic treatments with a post in the mesiobuccal canal; and distal post (DP) – a model of endodontic and prosthodontic treatments with a post in the distal canal. A vertical force of 300 N, perpendicular to the occlusal plane, was applied to one of five 1 mm² areas on the occlusal surface; mesial marginal ridge, distal marginal ridge, mesiobuccal cusp, distobuccal cusp, and central fossa. Finite element analysis was used to calculate the equivalent von Mises stresses on each root canal.

Results

The DP model showed similar maximum stress values to the NP model, while the MP model showed markedly greater maximum stress values. The post procedure increased stress concentration inside the canals, although this was significantly affected by the site of the force.

Conclusions

In the mandibular 1^st molar, the distal canal is the better place to insert the post than the mesiobuccal canal. However, if insertion into the mesiobuccal canal is unavoidable, there should be consideration on the occlusal contact, making central fossa and distal marginal ridge the main functioning areas.

Evaluation of Different Restoration Combinations Used in the Reattachment of Fractured Teeth: A Finite Element Analysis

Objective. The purpose of this study was to test different restoration combinations used for constructing fractured endodontically treated incisors by reattaching their fractured fragments. Methods. Seven types of 3-D FEM mathematical root canal-filled models were generated, simulating cases of (OB) reattaching fractured fragments; (CrPL) reattaching fractured fragments + ceramic palatinal laminate; (CmPL) reattaching fractured fragments + composite palatinal laminate; (CM) reattaching fractured fragments + coronal 1/3 of the root was filled using core material; (BP) reattaching fractured fragments + glass fiber post; (CP) composite resin restoration + glass fiber post; and (OC) composite resin restoration. A 100-N static oblique force was applied to the simulated teeth with 135° on the node at 2 mm above the cingulum to analyze the stress distribution at the tooth. Results. For enamel tissue, the highest stress values were observed in model BP, and the lowest stress values were observed in model CmPL. For dentine tissue, the highest stress concentrations were observed around the fracture line for all models. Conclusions. Reattachment of fractured fragments by bonding may be preferred as a restoration option for endodontically treated incisors; also, palatinal laminate decreases the stress values at tooth tissues, especially at the enamel and the fracture line.

"Ferrule Comes First. Post Is Second!" Fake News and Alternative Facts? A Systematic Review

INTRODUCTION

Both the role of an endodontic post and the ferrule effect have been discussed for decades. The clinical impact of endodontic posts compared with post-free restoration with or without ferrule support was not systematically reviewed so far. It was assumed that the effect of an endodontic post compared with a post-free restoration can be evaluated only when at the same time a ferrule or no-ferrule situation was clinically compared.

METHODS

The specific PICO question was as follows: Patient: adults with sufficient endodontic treatment needing a core or post; Intervention: post-endodontic treatment using posts with or without ferrule; Comparison: post-endodontic treatment without posts with or without ferrule; Outcomes: failure rates of post/core complexes with or without ferrule support. A Medline search was performed via PubMed in June 2017 using relevant electronic databases. Additionally, hand search was performed. Only prospective clinical studies in humans comparing the success/survival of teeth restored with or without posts over a minimum time of observation of 5 years were included.

RESULTS

In total, 7 randomized controlled trials and 1 prospective clinical trial met inclusion criteria. Cochrane rating showed high risk of bias in 5 studies. Two of 3 studies support the ferrule-effect concept. Seven of 8 show no post effect. Clinical evidence regarding the influence of tooth location on its survival is scarce.

CONCLUSION

Ferrule effect and maintaining cavity walls are the predominant factors with regard to tooth and restoration survival of endodontically treated teeth. Most studies do not confirm a positive effect of post placement.

Ferrule-Effect Dominates Over Use of a Fiber Post When Restoring Endodontically Treated Incisors: An In Vitro Study

OBJECTIVES

 The aim of this study was to investigate the restoration of broken-down endodontically treated incisors with the ferrule effect using glass ceramic crowns bonded to composite resin core buildups with or without a fiber post. A no-ferrule group with post was also included for comparison.

METHODS AND MATERIALS

 Thirty decoronated endodontically treated bovine incisors with a 2-mm ferrule were restored with a direct buildup using a nanohybrid direct composite resin (Miris 2 and Optibond FL) with or without a glass-fiber-reinforced post. An additional group of 15 teeth without a ferrule were restored with buildup and a fiber post. All teeth were prepared to receive bonded glass ceramic crowns (e.max CAD luted with Variolink Esthetic DC) and were subjected to accelerated fatigue testing. Cyclic isometric loading was applied to the incisal edge at an angle of 30° and a frequency of 5 Hz, beginning with a load of 100 N (×5000 cycles). A 100 N load increase was applied each 15,000 cycles. Specimens were loaded until failure or to a maximum of 1000 N (×140,000 cycles). Groups were compared using the Kaplan Meier survival analysis (log rank test at p=0.05).

RESULTS

 None of the tested specimens withstood all 140,000 load cycles. Specimens with posts but without a ferrule were affected by an initial failure phenomenon (wide gap at the lingual margin between the buildup/crown assembly and the root). There was a significant difference in mean survived cycles between the ferrule groups (Fp=73,332× and FNp=73,244×) and the no-ferrule group (50,121×; p=0.001). The addition of a fiber post was not significant in the presence of the ferrule (p=0.884). In both groups with posts, 100% of failures were unrestorable. The no-post group had 47% of restorable and possibly restorable failures.

CONCLUSIONS

 The survival of broken-down nonvital incisors was improved by the presence of the ferrule but not by the fiber-reinforced post. Fiber posts were always detrimental to the failure mode and were not able to compensate for the absence of a ferrule.

Survival of Restored Endodontically Treated Teeth in Relation to Periodontal Status

Abstract The aim of the present study was to investigate the success and survival of restored endodontically treated teeth (ETT) in a general practice environment related to periodontal parameters. Data from 360 restored ETT treated between 2000 and 2011 were collected. Dates of interventions like restorations, repairs, replacements and extractions were recorded. Additionally, general information about patients and dentitions as well as periodontal status was recorded. Success was analyzed using Kaplan-Meier statistics and a multivariate Cox regression analysis was performed to assess variables influencing success and survival. After a mean observation time of 4.34 years (range 0.6 - 11.6 years), 19 teeth were extracted and 27 restorations needed repair or replacement. According to the Cox regression, increasing maximum pocket depth of the tooth resulted in a higher risk for failure (p=0.012). In conclusion, periodontal pocket depth was found to be a significant factor in the survival of restored ETT.

Impact of a Core Ferrule Design on Fracture Resistance of Teeth Restored with Cast Post and Core

Objectives. To investigate the influence of a contra bevel on the fracture resistance of teeth restored with cast post and core. Materials and Methods. Sixty plastic analogues of an upper incisor were endodontically treated and prepared with 6° internal taper and 2 mm of ferrule in order to receive a cast post and core. The prepared samples were divided into two groups (n = 30); the first group serves as control while the second group was prepared with an external 30° bevel on the buccal and lingual walls. All samples crowned were exposed to a compressive load at 130° to their long axis until fractures occurred. Fracture resistance loads were recorded and failure modes were also observed. Mann-Whitney test was carried out to compare the two groups. Results. Mean failure loads for the groups were, respectively, 1038.69 N (SD ±243.52 N) and 1078.89 N (SD ±352.21 N). Statistically, there was no significant difference between the two groups (P = 0.7675 > 0.05). Conclusion. In the presence of a ferrule and a crown in the anterior teeth, adding a secondary ferrule to the cast post and core will not increase the resistance to fracture.

A 3-dimensional finite element analysis of the restoration of the maxillary canine with a complex zirconia post system

STATEMENT OF PROBLEM

Zirconia posts exhibit high strength and toughness, but reliable bonding with the resin core is difficult to attain. The use of a ferrule has been found to improve stress distribution in the root of endodontically treated teeth.

PURPOSE

The purpose of this finite element analysis study was to measure the stress distribution in the post-core system and root structure of a maxillary canine.

MATERIAL AND METHODS

A right maxillary canine was embedded and subjected to a micro-computed tomography scan. Three-dimensional dynamic scan data were then transformed, and a finite element model of 4 dentin ferrule heights was designed with zirconia posts and heat-pressed glass ceramics for a complete crown restoration. Von Mises stresses were determined by applying a 300 N static load to the middle of the lingual surface of the crown.

RESULTS

When the ferrule height increased from 0 to 3 mm, the maximum von Mises stress of the zirconia post decreased from 196 to 149 MPa, and that on the zirconia post-dentin interface decreased from 174 to 132 MPa. The maximum von Mises stress decreased from 39.8 to 32.5 MPa in the apical root and from 59.5 to 49.9 MPa in the mid-root when the ferrule height increased from 0 to 3 mm.

CONCLUSIONS

Increased ferrule height is associated with reduced von Mises stress in the zirconia post and the post-dentin interface, with an apparent shift of von Mises stress to the root cervical area from the mid-root and the apex.