Preconcentration of trace elements on a support impregnated with sodium diethyldithiocarbamate prior to their determination by inductively coupled plasma-atomic emission spectrometry

A newly-constructed bifunctional bacterial consortium for removing butyl xanthate and cadmium simultaneously from mineral processing wastewater: Experimental evaluation, degradation and biomineralization

Due to the technological limitations associated with beneficiation technology, large amounts of flotation reagents and heavy metals remain in mineral processing wastewater. Unfortunately, however, no treatment methods are available to mitigate the resulting pollution by them. In this study, a bacterial consortium SDMC (simultaneously degrade butyl xanthate and biomineralize cadmium) was constructed in an effort to simultaneously degrade butyl xanthate (BX) and biomineralize cadmium (Cd) by screening and domesticating two different bacterial species including Hypomicrobium and Sporosarcina. SDMC is efficient in removing the combined pollution due to BX and Cd with a 100% degradation rate for BX and 99% biomineralization rate for Cd within 4 h. Besides, SDMC can tolerate high concentrations of Fe(III) (0-40 mg/L). It has an excellent ability to utilize Fe(III) for enhanced removal of the combined pollutants. SDMC can effectively remove pollutants with a pH range of 6-9. Further, we discussed pathways for potential degradation and biomineralization: Cd(BX)₂-Cd²⁺, BX^-; BX^--CS₂, butyl perxanthate (BPX); Cd²⁺-(Ca0.67,Cd0.33)CO₃. The removal of the combined pollutants primarily entails decomposition, degradation, and biomineralization, C-O bond cleavage, and microbially induced carbonate precipitation (MICP). SDMC is a simple, efficient, and eco-friendly bifunctional bacterial consortium for effective treatment of BX-Cd combined pollution in mineral processing wastewater.

Microbial community structures and their driving factors in a typical gathering area of antimony mining and smelting in South China

This study investigated soil microbial community in a typical gathering area of antimony mining and smelting in South China. The physical and chemical properties of different soils (mining waste dumps, flotation tailings, and smelting slag) and depths (0-20 cm, 40-60 cm, and 80-100 cm) were compared. The results showed that antimony (Sb) and arsenic (As) were the main pollutants, and their concentrations were 5524.7 mg/kg and 3433.7 mg/kg, respectively. Xanthates were found in the flotation tailings and smelting slag, and the highest concentration was 585.1 mg/kg. The microbial communities were analyzed by high-throughput sequencing, and it was shown that Proteobacteria, Acidobacteria, Chlorobacterium, Bacteroides, and Actinomycetes were the dominant taxa at the phylum level. There were obvious differences in microbial community structure in different sites. The dominant microorganism in the mining site was Chujaibacter. Subgroup_2_unclassified and Gemmatimonadaceae_unclassified were the prevalent microorganisms in the flotation and smelting sites, respectively. As, Sb, and xanthates were the main factors affecting the diversity and composition of bacteria in the flotation tailings and smelting slag areas. Therefore, this study provides experimental guidance and a theoretical basis for soil antimony pollution quality assessment, biological treatment, and environmental remediation.

Effects of typical flotation reagent on microbial toxicity and nickel bioavailability in soil

The combined toxicological effects of nickel (Ni) and butyl xanthate (BX), that is commonly used in flotation reagents for non-ferrous metals ore processing such as Ni, copper and lead ores, on soil microbial communities were studied by determining soil microbial activity, soil enzyme activities and Ni bioavailability. The results revealed that the exchangeable (EXC) and reducible (RED) fractions of Ni were higher in Ni/BX mixture than Ni alone, probably because BX reacts with Ni to form complexes that lead an increase in bioavailability of Ni. The presence of BX and Ni inhibited microbial activity and enzyme activities during the first 30-days. Then, from 30 days to 180 days, different trends were observed according to the condition: microbial activity was stimulated with BX alone while it was inhibited with Ni/BX mixture. This observation was supported by the fact that the inhibitory ratio (I) was higher for Ni/BX mixture than BX alone. Results showed that the sensitivity to one or both contaminants followed the order: urease (UA) > invertase (INV). EXC fraction of Ni/BX mixture were significantly correlated with UA, INV, I, peak power (P_peak) and peak time (T_peak), respectively (p < 0.01), suggesting that Ni bioavailability might explain the Ni toxicity against microbial communities under combined pollution conditions. Such observations allow us to better understand toxic effects of Ni pollution when accompanied with BX, facilitating precisely evaluation of potential risks in mining areas.

Combined effects of antimony and sodium diethyldithiocarbamate on soil microbial activity and speciation change of heavy metals. Implications for contaminated lands hazardous material pollution in nonferrous metal mining areas

The combined effects of antimony (Sb) and sodium diethyldithiocarbamate (DDTC), a common organic flotation reagent, on soil microbial activity and speciation changes of heavy metals were investigated for the first time. The results showed that the exchangeable fraction of Sb was transformed to a stable residual fraction during the incubation period, and the addition of DDTC promoted the transformation compared with single Sb pollution, probably because DDTC can react with heavy metals to form a complex. In addition, the presence of DDTC and Sb inhibited the soil microbial activity to varying degrees. The growth rate constant k of different interaction systems was in the following order on the 28th day: control group ≥ single DDTC pollution > combined pollution > single Sb pollution. A correlation analysis showed that the concentration of exchangeable Sb was the primary factor that affected the toxic reaction under combined pollution conditions, and it significantly affected the characteristics of the soil microorganisms. All the observations provide useful information for a better understanding of the toxic effects and potential risks of combined Sb and DDTC pollution in antimony mining areas.

On-line microwave-based preconcentration device for inductively coupled plasma atomic emission spectrometry: application to the elemental analysis of spirit samples

A microwave-based thermal nebulizer (MWTN) has been employed for the first time as on-line preconcentration device in inductively coupled plasma atomic emission spectrometry (ICP-AES). By the appropriate selection of the experimental conditions, the MWTN could be either operated as a conventional thermal nebulizer or as on-line analyte preconcentration and nebulization device. Thus, when operating at microwave power values above 100 W and highly concentrated alcohol solutions, the amount of energy per solvent mass liquid unit (EMR) is high enough to completely evaporate the solvent inside the system and, as a consequence, the analyte is deposited (and then preconcentrated) on the inner walls of the MWTN capillary. When reducing the EMR to the appropriate value (e.g., by reducing the microwave power at a constant sample uptake rate) the retained analyte is swept along by the liquid-gas stream and an analyte-enriched aerosol is generated and next introduced into the plasma cell. Emission signals obtained with the MWTN operating in preconcentration-nebulization mode improved when increasing preconcentration time and sample uptake rate as well as when decreasing the nozzle inner diameter. When running with pure ethanol solution at its optimum experimental conditions, the MWTN in preconcentration-nebulization mode afforded limits of detection up to one order of magnitude lowers than those obtained operating the MWTN exclusively as a nebulizer. To validate the method, the multi-element analysis (i.e. Al, Ca, Cd, Cr, Cu, Fe, K, Mg, Mn, Na, Pb and Zn) of different commercial spirit samples in ICP-AES has been performed. Analyte recoveries for all the elements studied ranged between 93% and 107% and the dynamic linear range covered up to 4 orders of magnitude (i.e. from 0.1 to 1000μgL(-1)). In these analysis, both MWTN operating modes afforded similar results. Nevertheless, the preconcentration-nebulization mode permits to determine a higher number of analytes due to its higher detection capabilities.

Preconcentration technique for the determination of trace elements in natural water samples by ICP-AES

A procedure was developed for the determination of Cd, Cu, Zn, Co, Ni, Mn, Pb and Mo in water samples by inductively coupled plasma atomic emission spectrometry (ICP-AES) after preconcentration on a morpholine dithiocarbamate (mor-DTC) supported by bagasse (Saccharam aphisinaram). The sorbed elements were subsequently eluted with 4,M HNO3 and the acid eluates were analysed by ICP-AES. The influence of various parameters such as pH, flow rate of sample, eluent concentration, volume of the sample and volume of eluent were investigated to enhance the sensitivity of the present method. A 20,mL disposable syringe served as preconcentration column. Under the optimal conditions Cd, Cu, Zn, Co, Ni, Mn, Pb and Mo in aqueous sample was concentrated about 100-fold. The sorption recoveries of elements were higher than 99.6%. The method is also applied for the analysis of natural and spiked water samples.

Inductively Coupled Plasma-Optical Emission Spectrometry for On-Line Determination of Multi Trace Elements in Environmental Samples after Preconcentration by UsingBorassus flabellifer Inflorescence Loaded with 2-Propylpiperidine-1-carbodithioate

A procedure was developed for the determination of Cu, Mn, Pb, Cd, Co, Cr, and Zn in water samples by Inductively Coupled Plasma-Optical Emission Spectrometry (ICP-OES) after preconcentration on synthesized 2-propylpiperidine-1-carbodithioate supported by Borassus flabellifer Inflorescence (BFI). The sorbed element was subsequently eluted with 0.4 M HNO3, and the acid eluates were analyzed by ICP-OES. The influence of various parameters such as pH, flow rate of sample, eluent concentration, volume of the sample, and volume of eluent were investigated. Under the optimal conditions, Cu, Mn, Pb, Cd, Co, Cr, and Zn in aqueous samples were concentrated ca. 100-fold. Recoveries were obtained by the proposed method in the range of 97.8-99.9%. This method was also applied for the analysis of spiked, natural waters and soil samples. The results provide strong evidence to support the hypothesis of an adsorption mechanism.

Use of experimental design in the optimisation of a solid phase preconcentration system for Cobalt determination by GFAAS

In this work is proposed a solid phase preconcentration system of Co2+ ions and its posterior determination by GFAAS in which fractional factorial design and response surface methodology (RSM) were used for optimization of the variables associated with preconcentration system performance. The method is based on cobalt extraction as a complex Co2+-PAN (1:2) in a mini-column of polyurethane foam (PUF) impregnated with 1-(2-pyridylazo)-naphthol (PAN) followed by elution with HCl solution and its determination by GFAAS. The chemical and flow variables studied were pH, buffer concentration, eluent concentration and preconcentration and elution flow rates. Results obtained from fractional factorial design 2(5-1) showed that only the variables pH, buffer concentration and interaction (pH X buffer concentration) based on analysis of variance (ANOVA) were statistically significant at 95% confidence level. Under optimised conditions, the method provided an enrichment factor of 11.6 fold with limit of detection and quantification of 38 and 130 ng L-1, respectively, and linear range varying from 0.13 to 10 µg L-1. The precision (n = 9) assessed by relative standard deviation (RSD) was respectively 5.18 and 2.87% for 0.3 and 3.0 µg L-1 cobalt concentrations.

Spectrophotometric determination of trace iron(III) in natural water after its preconcentration with a chelating resin

A method for the determination of Fe(III) at trace levels is described. Thus prior to the spectrophotometric determination, a preconcentration of the trace amounts of iron(III) using a chelate forming resin is proposed. A strong base anion-exchange resin (Dowex 2X4) loaded with Ferron (7-iodo-8-hydroxyquinoline-5-sulphonic acid) was used for Fe(III) preconcentration, at pH 2.2. After desorption with 5% ascorbic acid in 0.5 M HCl, the analyze (converted from Fe(III) to Fe(II) was determined spectrophotometrically at 510 nm as Fe(II)-o-phenanthroline complex. The accuracy of the proposed method was verified by comparing the obtained results with those obtained using AAS with the standard addition method. The sensitivity of the spectrophotometric method (after preconcentration) was 0.01?g Fe(III)/ml. The recovery for iron(III) at the 7?g/l level was 97%.