Chemical accumulation and voltammetric determination of traces of nickel(II) at glassy carbon electrodes modified with dimethyl glyoxime containing polymer coatings

Electrochemical sensing platform based on Zeolite/Graphite/Dimethylglyoxime nanocomposite for highly selective and ultrasensitive determination of nickel

In this work, the fabrication and analytical application of a novel, unique, mercury-free, and user-friendly voltammetric sensor of Ni(II) based on glassy carbon electrode (GCE) modified with zeolite(MOR)/graphite(G)/dimethylglyoxime(DMG) composite (MOR/G/DMG-GCE) and the voltammetric procedure for highly selective, ultra-trace determination of nickel ions were reported for the first time. Deposition of a thin layer of the chemically active MOR/G/DMG nanocomposite enables the selective and effective accumulation of Ni(II) ions in the form of the DMG-Ni(II) complex. In 0.1 mol L^-1 ammonia buffer (pH 9.0), the MOR/G/DMG-GCE exhibited linear response in the Ni(II) ions concentration range of 0.86 - 19.61 µg L^-1 and 0.57 - 15.75 µg L^-1, for the accumulation time of 30 s and 60 s, respectively. For 60 s of accumulation time, the limit of detection (S/N = 3) was 0.18 µg L^-1 (3.04 nM), and sensitivity of 0.202 µA L µg^-1 was achieved. The developed protocol was validated by the analysis of wastewater certified reference materials. Its practical usefulness was confirmed by the determination of nickel released from metallic jewelry submerged in artificial sweat and stainless steel pot during water boiling. The obtained results were verified by electrothermal atomic absorption spectroscopy as a reference method.

Bismuth-Chitosan Nanocomposite Sensors for Trace Level Detection of Ni(II) and Co(II) in Water Samples

Trace minerals play an essential role in methane production via anaerobic digestion (AD). It is important to monitor Ni(II) and Co(II) concentrations and the Ni/Co concentration ratio for the rapid diagnosis of the ecological status or activity of methanogens in AD. Electrochemical detection of Ni(II) and Co(II) was investigated by coating the Bi-chitosan nanocomposite on a glassy carbon electrode (GCE) via the electrodeposition technique. A square-wave adsorptive cathodic stripping voltammetry technique (SWAdCSV) was applied and optimized when dimethylglyoxime (DMG) was used as the chelating agent for Ni(II) and Co(II) measurements. The SWAdCSV results showed that the current peaks for Co(II) detection are 6.1 times greater than the current peaks for Ni(II) measurements, probably due to the different affinity of DMG molecules between Ni(II) and Co(II). DMG molecules demonstrated higher selectivity toward Co(II) cations compared to Ni(II). The modified Bi-chitosan GCE developed in this study showed a relatively wide range of the Ni(II) and Co(II) concentrations (2–100 µg L−1) with a limit of detection of 3.6 µg L−1 for Ni(II) and 2.4 µg L−1 for Co(II), respectively. The developed sensor was applied to Ni(II) and Co(II) spiked natural water samples and showed good performance of detection with 12 consecutive measurements. Overall, the fabricated sensor showed excellent sensitivity toward Ni(II) and Co(II) in natural water samples.

Determination of Trace Levels of Nickel(II) by Adsorptive Stripping Voltammetry Using a Disposable and Low-Cost Carbon Screen-Printed Electrode

A commercial and disposable screen-printed carbon electrode (SPCE) has been proposed for a fast, simple and low-cost determination of Ni(II) at very low concentration levels by differential pulse adsorptive stripping voltammetry (DPAdSV) in the presence of dimethylglyoxime (DMG) as complexing agent. In contrast with previously proposed methods, the Ni(II)-DMG complex adsorbs directly on the screen-printed carbon surface, with no need of mercury, bismuth or antimony coatings. Well-defined stripping peaks and a linear dependence of the peak area on the concentration of Ni(II) was achieved in the range from 1.7 to 150 µg L−1, with a limit of detection of 0.5 µg L−1 using a deposition time of 120 s. An excellent reproducibility and repeatability with 0.3% (n = 3) and 1.5% (n = 15) relative standard deviation, respectively, were obtained. In addition, the suitability of the SPCE as sensing unit has been successfully assessed in a wastewater certificated reference material with remarkable trueness and very good reproducibility.

Complexation-Based Detection of Nickel(II) at a Graphene-Chelate Probe in the Presence of Cobalt and Zinc by Adsorptive Stripping Voltammetry

The adsorptive stripping voltammetric detection of nickel and cobalt in water samples at metal film electrodes has been extensively studied. In this work, a novel, environmentally friendly, metal-free electrochemical probe was constructed for the ultra-trace determination of Ni2+ in water samples by Adsorptive Cathodic Stripping Voltammetry (AdCSV). The electrochemical platform is based on the adsorptive accumulation of Ni2+ ions directly onto a glassy carbon electrode (GCE) modified with dimethylglyoxime (DMG) as chelating agent and a Nafion-graphene (NGr) nanocomposite to enhance electrode sensitivity. The nafion-graphene dimethylglyoxime modified glassy carbon electrode (NGr-DMG-GCE) shows superior detection capabilities as a result of the improved surface-area-to-volume ratio and enhanced electron transfer kinetics following the incorporation of single layer graphene, while limiting the toxic effects of the sensor by removal of the more common mercury, bismuth and lead films. Furthermore, for the first time the NGr-DMG-GCE, in the presence of common interfering metal ions of Co2+ and Zn2+ demonstrates good selectivity and preferential binding towards the detection of Ni2+ in water samples. Structural and morphological characterisation of the synthesised single layer graphene sheets was conducted by Raman spectrometry, HRTEM and HRSEM analysis. The instrumental parameters associated with the electrochemical response, including accumulation potential and accumulation time were investigated and optimised in addition to the influence of DMG and graphene concentrations. The NGr-DMG-GCE demonstrated well resolved, reproducible peaks, with RSD (%) below 5% and a detection limit of 1.5 µg L-1 for Ni2+ reduction at an accumulation time of 120 s., the prepared electrochemical sensor exhibited good detection and quantitation towards Ni2+ detection in tap water samples, well below 0.1 mg L-1 set by the WHO and EPA standards. This comparable to the South African drinking water guidelines of 0.15 mg L-1.

Rapid and direct electrochemical determination of Ni(II) in industrial discharge water

Industrial water contains a number of contaminants, such as organic pollutants and heavy metals, which can significantly affect the quality of soil, ground and environmental waters. We have successfully optimized and tested an electrochemical method and sensor modified with dimethylglyoxime for monitoring of nickel(II). The detection limit was 0.03mg/L and determination limit was 0.09mg/L. Linear concentration range was observed from 0.06 to 0.5mg/L Ni(II) and it is suitable for the analysis of environmental waters. The effect of all parameters important for on-site measurements (such as interferences, presence of dissolved oxygen, temperature) was investigated and considered in the analysis of mine discharge water. Water samples were analyzed without any pretreatment or filtration. A low level of error (5.6%) was observed for analysis demonstrating the usability of the optimized sensor and method for on-site measurements.