Lipase-catalyzed synthesis of tricaprylin in a medium solely composed of substrates. Water production and elimination

Ultrasound pretreatment as a novel approach for intensification of lipase catalyzed esterification of tricaprylin

The current work deals with ultrasound assisted intensification of synthesis of tricaprylin based on the enzyme catalyzed reaction of caprylic acid and glycerol with novel approach of using ultrasound in only the initial stages of the reaction. Two types of immobilized lipases as Lipozyme RM (Rhizomucor miehei) and Novozym 435 (Candida antarctica) have been used in the work. The effect of ultrasonic conditions such as treatment time and power as well as the reaction conditions such as substrate molar ratio, reaction time and enzyme loading on the yield of tricaprylin has been investigated. It was established that the optimum pretreatment conditions were irradiation time as 30min with ultrasonic frequency of 20kHz, supplied power of 240W, 70% duty cycle (7s on 3s off cycle) whereas the optimum reaction conditions were 4:1 molar ratio of caprylic acid to glycerol, enzyme loading as 3% and operating temperature of 50°C. It was also established that reuse of enzymes for 10 cycles was possible without any significant effect on the activity of lipase. It was also conclusively established that compared to the conventional approach of synthesis, ultrasound pretreatment based approach greatly influenced the rate of reaction and maximum tricaprylin yield of 94.8% was achieved in 7h of reaction time under the optimum conditions.

Computer-aided control of water activity for lipase-catalyzed esterification in solvent-free systems

A computer system for on-line monitoring and control of the water activity (a(w)) in solvent-free media has been developed. The performance of this system was investigated by carrying out the lipase-catalyzed esterification of n-capric acid with n-decyl alcohol. A humidity sensor measured the relative humidity in the reactor headspace, which was then transmitted electrically to a digital computer that was used as a feedback controller. The water activity control was achieved by sparging either humidified air or dried air through the reaction medium at a flow rate determined by the digital feedback controller. The use of humid air and dry air for a(w) control made it possible to induce a larger a(w) gradient and thereby higher water transfer rate. As a result, the water activity quickly reached the desired a(w) values. We tested whether water activity in the reaction medium can be monitored by measuring relative humidity in the headspace. When the water activity in the liquid phase was determined from measurements of water content in the medium and compared to that measured directly with the humidity sensor, the a(w) in the reaction medium did not differ significantly from that in the headspace. This indicates that there is a near-equilibrium between the liquid medium and the exit air stream. Water activity was also successfully maintained close to the set point despite the massive production of water during the esterification process. Thus, the control system developed in this study is particularly useful for systems where large amounts of water are produced and where conventional methods make it difficult to control water activity as a result of a low water transfer rate. The effects that computer control of the water activity had on the reaction rate and yield were also examined. The reaction yield was significantly improved with water activity control. The conversions obtained at 28 h without and those with water activity control were 70% and 96%, respectively. In addition, from the fact that the final yields increased with decreasing a(w), computer-aided water activity control was performed with a set-point change. By controlling a(w) at 0.55 during initial reaction phase, followed by a step change of a(w) from 0.55 to 0 after 11 h of reaction, it was possible to enhance the final conversion to 100%.

Highly enantioselective esterification of racemic ibuprofen in a packed bed reactor using immobilised Rhizomucor miehei lipase

A systematic study of the enantioselective resolution of ibuprofen by commercial Rhizomucor miehei lipase (Lipozyme(R) IM20) has been carried out using isooctane as solvent and butanol as esterificating agent. The main variables controlling the process (temperature, ibuprofen concentration, ratio butanol:ibuprofen) have been studied using an orthogonal full factorial experimental design, in which the selected objective function was enantioselectivity. This strategy has resulted in a polynomial function that describes the process. By optimizing this function, optimal conditions for carrying out the esterification of racemic ibuprofen have been determined. Under these conditions, enantiomeric excess and total conversion values were 93.8% and 49.9%, respectively, and the enantioselectivity was 113 after 112 h of reaction. These conditions have been considered in the design of a continuous reactor to scale up the process. The esterification of ibuprofen was properly described by pseudo first-order kinetics. Thus, a packed bed reactor operating as a plug-flow reactor (PFR) is the most appropriate in terms of minimizing the residence time compared with a continuous stirred tank reactor (CSTR) to achieve the same final conversion. This reactor shows a similar behavior in terms of enantioselectivity, enantiomeric excess, and conversion when compared with batch reactors. A residence-time distribution (RTD) shows that the flow model is essentially a plug flow with a slight nonsymmetrical axial dispersion (Peclet number = 43), which was also corroborated by the model of CSTR in series. The stability of the system (up to 100 h) and the possibility of reutilization of the enzyme (up to four times) lead to consider this reactor as a suitable configuration for scale up of the process.