Alumina bearings in hip replacement: Theoretical and practical aspects

Biomaterial Properties of Femur Implant on Acetabulum Erosion: A Review

The hip is one in every of the various joint at intervals the body. The correct operating of this joint is essential. For the aim once the hip is injured whole, a substitution procedure of the entire joint ought to be done to reinstate its operating, that is known as absolute hip surgical process. It is finished with the assistance of inserts of various biomaterials, as an example, polymers, metals, and pottery. The primary issues with regard to the utilization of various biomaterials are the reaction of the body's instrument to wear trash. Throughout this audit, biomaterials that are developing is talked regarding aboard the wear and tear and tear conduct and instrument. To boot, the numerous properties of the biomaterials are talked regarding aboard the expected preferences and drawbacks of their utilization. Further, the blends of various biomaterials at intervals the articulating surfaces are cleft and so the problems regarding their utilization are assessed. This paper hopes to passes away an in depth review of the trauma fringe of bearing surfaces of hip prosthetic devices. Additionally, this paper can offer AN ordered blueprint of the materials nearby their favorable circumstances and detriments and besides the conceivable outcomes of use. Keywords: - Hip implant; Biomaterials; Wear mechanism; Bearing surfaces; Polymers

Evaluation of silicon nitride as a wear resistant and resorbable alternative for total hip joint replacement

Many of the failures of total joint replacements are related to tribology, i.e., wear of the cup, head and liner. Accumulation of wear particles at the implants can be linked to osteolysis which leads to bone loss and in the end aseptic implant loosening. Therefore it is highly desirable to reduce the generation of wear particles from the implant surfaces. Silicon nitride (Si(3)N(4)) has shown to be biocompatible and have a low wear rate when sliding against itself and is therefore a good candidate as a hip joint material. Furthermore, wear particles of Si(3)N(4) are predicted to slowly dissolve in polar liquids and they therefore have the potential to be resorbed in vivo, potentially reducing the risk for aseptic loosening. In this study, it was shown that α-Si(3)N(4)-powder dissolves in PBS. Adsorption of blood plasma indicated a good acceptance of Si(3)N(4) in the body with relatively low immune response. Si(3)N(4) sliding against Si(3)N(4) showed low wear rates both in bovine serum and PBS compared with the other tested wear couples. Tribofilms were built up on the Si(3)N(4) surfaces both in PBS and in bovine serum, controlling the friction and wear characteristics.

Fabrication and evaluation of SixNy coatings for total joint replacements

Wear particles from the bearing surfaces of joint implants are one of the main limiting factors for total implant longevity. Si(3)N(4) is a potential wear resistant alternative for total joint replacements. In this study, Si(x)N(y)-coatings were deposited on cobalt chromium-discs and Si-wafers by a physical vapour deposition process. The tribological properties, as well as surface appearance, chemical composition, phase composition, structure and hardness of these coatings were analysed. The coatings were found to be amorphous or nanocrystalline, with a hardness and coefficient of friction against Si(3)N(4) similar to that found for bulk Si(3)N(4). The low wear rate of the coatings indicates that they have a potential as bearing surfaces of joint replacements. The adhesion to the substrates remains to be improved.

Two-dimensional finite element simulation of fracture and fatigue behaviours of alumina microstructures for hip prosthesis

This paper describes a two-dimensional (2D) finite element simulation for fracture and fatigue behaviours of pure alumina microstructures such as those found at hip prostheses. Finite element models are developed using actual Al2O3 microstructures and a bilinear cohesive zone law. Simulation conditions are similar to those found at a slip zone in a dry contact between a femoral head and an acetabular cup of hip prosthesis. Contact stresses are imposed to generate cracks in the models. Magnitudes of imposed stresses are higher than those found at the microscopic scale. Effects of microstructures and contact stresses are investigated in terms of crack formation. In addition, fatigue behaviour of the microstructure is determined by performing simulations under cyclic loading conditions. It is shown that crack density observed in a microstructure increases with increasing magnitude of applied contact stress. Moreover, crack density increases linearly with respect to the number of fatigue cycles within a given contact stress range. Meanwhile, as applied contact stress increases, number of cycles to failure decreases gradually. Finally, this proposed finite element simulation offers an effective method for identifying fracture and fatigue behaviours of a microstructure provided that microstructure images are available.