Evaluation of solubility and dissolution profile of itraconazole after cogrinding with various hydrophilic carriers

Self-emulsifying micelles as a drug nanocarrier system for itraconazole oral bioavailability enhancement; in vitro and in vivo assessment

Itraconazole (ITZ) is a renowned antifungal medication, however its therapeutic efficacy is limited by low solubility and oral bioavailability. The current research work attempted to augment the oral bioavailability of ITZ by incorporating into self-emulsifying micelles (SEMCs). To fabricate the SEMCs, various preparation techniques including physical mixture, melt-emulsification, solvent evaporation and kneading, were opted by using different weight ratio of drug and solubilizers i.e. Gelucire-50/13 or Gelucire-44/14 and characterized both in vitro and in vivo. The prepared SEMCs were found to be in the size range from 63.4 ± 5.2 to 284.2 ± 19.5 nm with surface charges ranging from -16 ± 1.2 to -27 ± 2.0 mV. The drug solubility was improved to a reasonable extent with all investigated formulations, however, SEMCs in group 6 prepared by kneading method (KMG6) using Gelucire-44/14: drug (10:1 presented 87.6 folds' increase (964.93 ± 2 μg/mL) compared to solubility of crystalline ITZ (11 ± 2 μg/mL) through kneading method. In addition, KMG6 SEMCs shows the fast drug release compared to other SEMCs. Further, KMG6 SEMCs also exhibited 5.12-fold higher relative intestinal serosal fluid absorption compared to crystalline ITZ. The pharmacokinetic parameters such Cmax, AUC and Tmax of KMG6 SEMCs significantly improved compared to crystalline ITZ. In conclusion, the manipulation of ITZ solubility, dissolution rate and absorption using SEMCs is a promising strategy for bioavailability enhancement.

Mechanistic study of dissolution enhancement by interactive mixtures of chitosan with meloxicam as model

To enhance dissolution rate of meloxicam (MX), a poorly soluble model drug, a natural polysaccharide excipient chitosan (CH) is employed in this work as a carrier to prepare binary interactive mixtures by either mixing or co-milling techniques. The MX-CH mixtures of three different drug loads were characterized for morphological, granulometric, and thermal properties as well as drug crystallinity. The relative dissolution rate of MX was determined in phosphate buffer of pH 6.8 using the USP-4 apparatus; a significant increase in MX dissolution rate was observed for both mixed and co-milled mixtures comparing to the raw drug. Higher dissolution rate of MX was evidently connected to surface activation by mixing or milling, which was pronounced by the higher specific surface energy as detected by inverse gas chromatography. In addition to the particle size reduction, the carrier effect of the CH was confirmed for co-milling by linear regression between the MX maximum relative dissolution rate and the total surface area of the mixture (R² = 0.863). No MX amorphization or crystalline structure change were detected. The work of adhesion/cohesion ratio of 0.9 supports the existence of preferential adherence of MX to the coarse particles of CH to form stable interactive mixtures.

Feasibility of electrospray deposition for rapid screening of the cocrystal formation and single step, continuous production of pharmaceutical nanococrystals

OBJECTIVES

This study employed electrospray deposition (ESD) for simultaneous synthesis and particle engineering of cocrystals.

SIGNIFICANCE

Exploring new methods for the efficient production of cocrystals with desired particle properties is an essential demand.

METHODS

The possibility of cocrystal formation by ESD was examined for indomethacin-saccharin, indomethacin-nicotinamide, naproxen-nicotinamide, and naproxen-iso-nicotinamide cocrystals. Solutions of the drug and coformer at stoichiometric ratios were sprayed to a high electric field which caused rapid evaporation of the solvent and the formation of fine particles. The phase purity, size, and morphology of products were compared with reference cocrystals. Experiments were performed to evaluate the effects of stoichiometric ratio, concentration and solvent type on the cocrystal formation. Physical stability and dissolution properties of the electrosprayed cocrystals were also compared with reference cocrystals.

RESULTS

ESD was found to be an efficient and rapid method to produce cocrystals for all studied systems other than indomethacin-nicotinamide. Pure cocrystals only formed at a specific drug:coformer ratio. The solvent type has a weak effect on the cocrystal formation and morphology. Electrosprayed cocrystals exhibited nano to micrometer sizes with distinct morphologies with comparable physical stability with reference cocrystals. Nanococrystals of indomethacin-saccharin with a mean size of 219 nm displayed a threefold higher dissolution rate than solvent evaporated cocrystal.

CONCLUSION

ESD successfully was utilized to produce pure cocrystals of poorly soluble drugs with different morphologies and sizes ranging from nano to micrometer sizes in one step. This study highlighted the usefulness of ESD for simultaneous preparation and particle engineering of pharmaceutical cocrystals.