Contributions of Condensable Particulate Matter to Atmospheric Organic Aerosol over Japan

Condensable particulate matter emissions regulated by flue gas desulfurization technologies in typical industrial plants

Condensable particulate matter (CPM) emissions have exceeded filterable particulate matter from industrial plants under strict emission standards. However, how CPM emission characteristics are affected by air pollution control devices (especially end-of-pipe flue gas desulfurization (FGD) systems) remains to be investigated. Here, we systematically demonstrated CPM emissions regulated by various FGD systems through field measurements of 22 typical industrial sites. Inorganic CPM (57.6 ∼ 99.5 % of CPM) predominantly consisted of water-soluble ions, whose concentrations were distinct between the inlet and outlet of FGD units. SO42- or Cl- mainly contributed to inorganic CPM before desulfurization, while SO42- and NH4+ accounted for 49.2 ∼ 96.3 % of inorganic CPM after FGD. Higher removal efficiencies for Cl- (98.1 ± 1.9 %) than SO42- (50.1 ± 23.8 %) in partial lime-gypsum-wet FGD systems could convert Cl--rich CPM into SO42--rich CPM. Ammonia-wet FGD and activated coke FGD failed to address NH3 slip issues effectively, leading to NH4+- rich (44.0 ∼ 96.0 %) CPM after desulfurization. Conversions of precursors (i.e., NH3, HCl, and SO3) before and after FGD were consistent with those of water-soluble ions. This study revealed chemical-specific transformations of CPM under different FGD processes, highlighting the control of the NH3 slip to reduce CPM emissions.

Study on the phase transformation mechanism and influencing factors of inorganic condensable particulate matter from coal-fired power plants

In this study, the concentration of inorganic ions (SO42-, NH4+, NO3- and NO2-) and morphological characteristics of condensable particulate matter (CPM) were investigated to elucidate the formation mechanism of inorganic CPM from ultra-low emission coal-fired power plants. The concentration of inorganic ions increased with the increase of H2O content and concentration of inorganic gaseous contaminants (SO2, NOX and NH3), and decrease of condensation temperature, indicating the enhancement of heterogenous reaction in the saturated flue gas. Furthermore, NOX and SO2 could undergo redox reactions, leading to an elevation in the concentration of SO42- and NO3-. Additionally, the introduction of NH3 resulted in increased concentrations of SO42-, NO3-, and NO2-, highlighting the significant role of NH3 neutralization in CPM nucleation. The condensation of SO3/sulfuric acid aerosols was enhanced under saturation conditions, and SO2 and SO3/sulfuric acid aerosols could contribute synergistically to the formation of SO42-. Moreover, morphological analysis revealed the presence of both well-aggregated solid CPM and dispersed liquid CPM, confirming the formation of inorganic CPM during fast condensation. Furthermore, the detected CPM were composed of S and O, which identified the significant role of sulfates in the inorganic CPM. These findings provide valuable insights for the control of inorganic CPM in flue gas systems.

Potential Strategy to Control the Organic Components of Condensable Particulate Matter: A Critical Review

More and more attention has been paid to condensable particulate matter (CPM) since its emissions have surpassed that of filterable particulate matter (FPM) with the large-scale application of ultralow-emission reform. CPM is a gaseous material in the flue stack but instantly turns into particles after leaving the stack. It is composed of inorganic and organic components. Organic components are an important part of CPM, and they are an irritant, teratogenic, and carcinogenic, which triggers photochemical smog, urban haze, and acid deposition. CPM organic components can aggravate air pollution and climate change; therefore, consideration should be given to them. Based on existing methods for removing atmospheric organic pollutants and combined with the characteristics of CPM organic components, we provide a critical overview from the aspects of (i) fundamental cognition of CPM, (ii) common methods to control CPM organic components, and (iii) catalytic oxidation of CPM organic components. As one of the most encouraging methods, catalytic oxidation is discussed in detail, especially in combination with selective catalytic reduction (SCR) technology, to meet the growing demands for multipollutant control (MPC). We believe that this review is inspiring for a fuller understanding and deeper exploration of promising approaches to control CPM organic components.

Migration and distribution characteristics of typical organic pollutants in condensable particulate matter of coal-fired flue gas and by-products of wet flue gas desulfurization system

The wet flue gas desulfurization (WFGD) system of coal-fired power plants shows a good removal effect on condensable particulate matter (CPM), reducing the dust removal pressure for the downstream flue gas purification devices. In this work, the removal effect of a WFGD system on CPM and its organic pollutants from a coal-fired power plant was studied. By analyzing the organic components of the by-products emitted from the desulfurization tower, the migration characteristics of organic pollutants in gas, liquid, and solid phases, as well as the impact of desulfurization towers on organic pollutants in CPM, were discussed. Results show that more CPM in the flue gas was generated by coal-fired units at ultra-low load, and the WFGD system had a removal efficiency nearly 8% higher than that at full load. The WFGD system had significant removal effect on two typical esters, especially phthalate esters (PAEs), with the highest removal efficiency of 49.56%. In addition, the WFGD system was better at removing these two esters when the unit was operating at full load. However, it had a negative effect on n-alkanes, which increased the concentration of n-alkanes by 8.91 to 19.72%. Furthermore, it is concluded that the concentration distribution of the same type of organic pollutants in desulfurization wastewater was similar to that in desulfurization slurry, but quite different from that in coal-fired flue gas. The exchange of three organic pollutants between flue gas and desulfurization slurry was not significant, while the concentration distribution of organic matters in gypsum was affected by coal-fired flue gas.

The effect of multiple factors on changes in organic-inorganic fractions of condensable particulate matter during coal combustion

Condensable particulate matter (CPM) from coal combustion is the focus of current pollutant emission studies, and CPM can be divided into inorganic and organic fractions according to the component characteristics. At present, the effects of different factors in the combustion process on the organic and inorganic components of CPM have not been discussed systematically. Here, we conducted combustion experiments collected the generated CPM on a well-controlled drip tube furnace, and investigated the effects of different factors on the generation of organic and inorganic components of CPM by varying the furnace wall insulation temperature, the ratio of gas supply components and the water vapor content in the flue gas. The results showed that the increase in combustion temperature (1300-1500 °C) and oxygen concentration (15-25%) reduced the total CPM generation by 9.8% and 19.98%, respectively, and the intervention of water vapor increased the ability of the whole CPM sampling device to capture ultrafine condensable particles. The generation of CPM organic components decreased with the enhancement of combustion temperature and oxygen content on combustion characteristics, and alkanes shifted to low carbon content. The amount of CPM inorganic components increased with the increase of water vapor content in the flue gas, and this change was dominated by SO42-. The above results provide a feasible idea for the next step of the precise reduction of CPM components.

Uncertainties in source allocation of carbonaceous aerosols in a Mediterranean region

Understanding the atmospheric processes involving carbonaceous aerosols (CAs) is crucial for assessing air pollution impacts on human health and climate. The sources and formation mechanisms of CAs are not well understood, making it challenging to quantify impacts in models. Studies suggest residential wood combustion (RWC) and traffic significantly contribute to CAs in Europe's urban and rural areas. Here, we used an atmospheric chemistry model (MONARCH) and three different emission inventories (two versions of the European-scale emission inventory CAMS-REG_v4 and the HERMESv3 detailed national inventory for Spain) to assess the uncertainties in CAs simulation and source allocation (from traffic, RWC, shipping, fires and others) in Northeast Spain. For this, black carbon (BC) and organic aerosol (OA) measurements performed at three supersites representing different environments (urban, regional and remote) were used. Our findings show the importance of model resolution and detailed emission input data in accurately reproducing BC/OA observations. Even though emissions of total particulate matter are rather consistent between inventories in Spain, we found discrepancies between them mainly related to the spatiotemporal disaggregation (particularly relevant for traffic and RWC) and the treatment of the condensable fraction of CAs in RWC (changes in the speciation of elemental/organic carbon). The main source contribution to BC concentrations in the urban site is traffic, accounting for 71.1%/65.2% (January/July) in close agreement with the fossil contribution derived from observations (78.8%/84.2%), followed by RWC (12.8%/3%) and shipping emissions (5.4%/13.8%). An over-representation of RWC (winter) and shipping (summer) is obtained with CAMS-REG_v4. Noteworthy uncertainties arise in OA results due to condensables in emissions and a limited secondary aerosol production in the model. These findings offer insights into MONARCH's effectiveness in simulating CAs concentrations and source contribution in Northeast Spain. The study highlights the benefits of combining new datasets and modeling techniques to refine emission inventories and better understand and mitigate air pollution impacts.

Source apportionment of anthropogenic and biogenic organic aerosol over the Tokyo metropolitan area from forward and receptor models

Organic aerosol (OA) is a dominant component of PM2.5, and accurate knowledge of its sources is critical for identification of cost-effective measures to reduce PM2.5. For accurate source apportionment of OA, we conducted field measurements of organic tracers at three sites (one urban, one suburban, and one forest) in the Tokyo Metropolitan Area and numerical simulations of forward and receptor models. We estimated the source contributions of OA by calculating three receptor models (positive matrix factorization, chemical mass balance, and secondary organic aerosol (SOA)-tracer method) using the ambient concentrations, source profiles, and production yields of OA tracers. Sensitivity simulations of the forward model (chemical transport model) for precursor emissions and SOA formation pathways were conducted. Cross-validation between the receptor and forward models demonstrated that biogenic and anthropogenic SOA were better reproduced by the forward model with updated modules for emissions of biogenic volatile organic compounds (VOC) and for SOA formation from biogenic VOC and intermediate-volatility organic compounds than by the default setup. The source contributions estimated by the forward model generally agreed with those of the receptor models for the major OA sources: mobile sources, biomass combustion, biogenic SOA, and anthropogenic SOA. The contributions of anthropogenic SOA, which are the main focus of this study, were estimated by the forward and receptor models to have been between 9 % and 15 % in summer 2019. The observed percent modern carbon data indicate that the amounts of anthropogenic SOA produced during daytime have substantially declined from 2007 to 2019. This trend is consistent with the decreasing trend of anthropogenic VOC, suggesting that reduction of anthropogenic VOC has been effective in reducing anthropogenic SOA in the atmosphere.

The effect of air pollution control devices in coal-fired power plants on the removal of condensable and filterable particulate matter

Total particulate matter (TPM), including condensable and filterable particulate matter (CPM and FPM), is one of the pollutants that need to be controlled in the coal combustion process. In this study, CPM and FPM were sampled from sixteen coal-fired power units and two coal-fired industrial units. The removal effects of air pollution control devices equipped in the units on the migration and emission of particles were investigated by analyzing samples from inlets and outlets of apparatus. The average removal efficiency of TPM by dry-type dust removal equipment, wet flue gas desulfurization devices, and wet-type precipitators reached 98.57 ± 0.90%, 44.89 ± 15.01%, and 28.45 ± 7.78%, respectively. The removal efficiency of dry-type dust removal equipment and wet-type precipitators to TPM is mainly determined by the purification effect of FPM and CPM, respectively, and both types of particles contribute to the removal efficiency of desulfurization systems to total TPM. The concentrations of CPM (12.01 ± 5.64 mg/Nm³) and FPM (1.95 ± 0.86 mg/Nm³) emitted from ultra-low emission units were the lowest, and CPM is the dominant particle, especially the higher proportion of organic components in CPM.

Emission characteristics of condensable particulate matter (CPM) from FCC flue gas

Particulate matter (PM) as a major air pollutant, generally includes filterable particulate matter (FPM) and condensable particulate matter (CPM). CPM has gradually attracted widespread attention recently, due to its increasing proportion in total PM emissions. Fluid catalytic cracking (FCC) units, the main emission source in refineries, mostly use wet flue gas desulfurization (WFGD), which will produce a large amount of CPM. However, CPM emission and composition of FCC units are actually unclear. In this work, we aimed to understand the emission characteristics of CPM in FCC flue gas and provide some potential control strategies. Here, the stack tests of three typical FCC units were conducted to monitor FPM and CPM, and the field monitoring FPM results are higher than the concentration provided by Continuous Emission Monitoring System (CEMS). The emission of CPM is at a high-level concentration from 28.88 to 86.17 mg/Nm³, divided into inorganic fraction and organic fraction. The inorganic fraction is mainly composed in CPM, where water-soluble ions including SO₄^2-, Na⁺, NH₄⁺, NO₃^-, CN^-, Cl^-, and F^-, are the major contributors. Moreover, a variety of organic compounds are detected as qualitative analysis of organic fraction in CPM, which can be roughly classified into alkanes, esters, aromatics, and others. Finally, on the basis of the understanding of the characteristics of CPM, we have proposed two strategies for CPM control. This work is expected to advance CPM emission regulation and control in FCC units.

Developed compositional source profile and estimated emissions of condensable particulate matter from coal-fired power plants: A case study of Yantai, China

The emission and environmental impact of condensable particulate matter (CPM) from coal-fired power plants (CFPPs) are of increasing concern worldwide. Many studies on the characteristics of CPM emission have been conducted in China, but its source profile remains unclear, and its emission inventory remains high uncertainty. In this work, the latest measurements reported in the latest 33 studies for CPM inorganic and organic species emitted from CFPPs in China were summarized, and then a compositional source profile of CPM for CFPPs was developed for the first time in China, which involved 10 inorganic species and 71 organic species. In addition, the CPM emission inventory of CFPPs in Yantai of China was developed based on surveyed activity data, continuous emission monitoring system (CEMS), and the latest measurement data. The results show that: (1) Inorganic species accounted for 77.64 % of CPM emitted from CFPPs in Yantai, among which SO₄^2- had the highest content, accounting for 23.74 % of CPM, followed by Cl^-, accounting for 11.95 %; (2) Organic matter accounted for 22.36 % of CPM, among which alkanes accounted for the largest proportion of organic fraction (72.7 %); (3) Emission concentration method (EC) and CEMS-based emission ratio method (ER_FPM,CEMS) were recommended to estimate CPM emissions for CFPPs; (4) The estimated CPM emission inventories of Yantai CFPPs in 2020 by the EC method and the ER_FPM,CEMS method were 1231 tons and 929 tons, respectively, with uncertainties of -34 % ∼ 33 % and -27 % ∼ 57 %, respectively; (5) CPM emissions were mainly distributed in the northern coastal areas of Yantai. This developed CPM source profile and emission inventory can provide basic data for assessing the impacts of CPM on air quality and health. In addition, this study can provide an important methodology for developing CPM emission inventories and CPM emission source profiles for stationary combustion sources in other regions.

Variation of nitrate and nitrite in condensable particulate matter from coal-fired power plants under the simulated rapid condensing conditions

In this work, condensation temperature, H₂O vapor, SO₂, SO₃ and NH₃ were studied to explore the formation mechanism of nitrate ions (NO₃^-) and nitrite ions (NO₂^-) in condensable particulate matter (CPM) discharged by ultra-low emission coal-fired power plants. Some important results were obtained: (i) The concentration of NO₃^- and NO₂^- increased with the decrease of condensation temperature, and H₂O vapor could also promote the formation of NO₃^- and NO₂^-. (ii) The effects of SO₂ and SO₃ varied at different saturated states of flue gas, which was caused by the redox reaction of SO₂ and NO_X or the formation of H₂SO₄. (iii) NH₃ could promote the nucleation of NO₃^- and NO₂^-, and the promotion effect also existed in the existence of SO₂ or SO₃. It is worth mentioning that SO₃ and SO₂ might synergistically inhibit the formation of NO₃^- and NO₂^-, regardless of the presence of NH₃. The research results would enrich peoples understanding of the chemical and physical characteristics of NO₃^- and NO₂^- in CPM and provide a basic reference for the control of CPM emitted from coal-fired power plants.

Suggestion on further strengthening ultra-low emission standards for PM emission from coal-fired power plants in China

China has established the largest clean coal-fired power generation system in the world by accomplishing the technological transformation of coal-fired power plants (CFPPs) to achieve ultra-low emission. The potential for further particulate matter (PM) emission reduction to achieve near-zero emission for CFPPs has become a hotspot issue. In this study, PM emission from some ultra-low emission CFPPs adopting advanced air pollutant control technologies in China was reviewed. The results revealed that the average filterable particulate matter (FPM) concentration, measured as the total particulate matter (TPM) according to the current national monitoring standard, was (1.67±0.86) mg/m³, which could fully achieve the ultra-low emission standard for key regions (5 mg/m³), but that achieving the near-zero emission standard was difficult (1 mg/m³). However, the condensable particulate matter (CPM), with an average concentration of (1.06±1.28) mg/m³, was generally ignored during monitoring, which led to about 38.7% underestimation of the TPM. Even considering both FPM and CPM, the TPM emission from current CFPPs would contribute to less than 5% of atmospheric PM_2.5 concentrations in the key cities and regions in China. Therefore, further reduction in FPM emission proposed by the near-zero emission plan of CFPPs may have less environmental benefit than emission control of other anthropogenic sources. However, it is suggested that the management of CPM emission should be strengthened, and a national standard for CPM emission monitoring based on the indirect dilution method should be established for CFPPs. Those measurements are helpful for optimal operation of air pollutant control devices and continuously promoting further emission reduction.

Development of Volatility Distributions for Organic Matter in Biomass Burning Emissions

The volatility distribution of organic emissions from biomass burning and other combustion sources can determine their atmospheric evolution due to partitioning/aging. The gap between measurements and models predicting secondary organic aerosol has been partially attributed to the absence of semi- and intermediate volatility organic compounds (S/I-VOC) in models and measurements. However, S/I-VOCs emitted from these sources and typically quantified using the volatility basis framework (VBS) are not well understood. For example, the amount and composition of S/I-VOCs and their variability across different biomass burning sources such as residential woodstoves, open field burns, and laboratory simulated open burning are uncertain. To address this, a novel filter-in-tube sorbent tube sampling method collected S/I-VOC samples from biomass burning experiments for a range of fuels and combustion conditions. Filter-in-tube samples were analyzed using thermal desorption-gas chromatography-mass spectrometry (TD/GC/MS) for compounds across a wide range of volatilities (saturation concentrations; -2 ≤ logC* ≤ 6). The S/I-VOC measurements were used to calculate volatility distributions for each emissions source. The distributions were broadly consistent across the sources with IVOCs accounting for 75% - 90% of the total captured organic matter, while SVOCs and LVOCs were responsible for 6% - 13% and 1% - 12%, respectively. The distributions and predicted partitioning were generally consistent with literature. Particulate matter emission factors spanned two orders of magnitude across the sources. This work highlights the potential of inferring gas-particle partitioning behavior of biomass burning emissions using filter-in-tube sorbent samples analyzed offline. This simplifies both sampling and analysis of S/I-VOCs for studies focused on capturing the full range of organics emitted.

Emissions of Condensable Organic Aerosols from Stationary Combustion Sources over Japan

Treatment of condensable particulate matter (CPM) is key for accurate simulation of atmospheric particulate matter (PM), because conventional stationary combustion source emission surveys do not measure CPM in many countries. This study updates previously estimated CPM emissions from stationary combustion sources in Japan by considering the relationship between the CPM fraction and filterable PM (FPM) concentrations for individual sources rather than using a uniform CPM/FPM ratio for all sources. As a result, the total emissions ratio of condensable organic aerosol (OA) and filterable PM2.5 (OA CPM ∕ PM 2.5 FPM ) from stationary combustion sources, based on this update, changes from ~2.0 to 0.20, and the estimated concentrations of condensable OA, averaged over winter and over summer, changes from up to 3 μg m-3 to up to 0.2 μg m-3. The normalized mean bias for concentration of the simulated organic carbon (OC) in winter changes from -78% ~ -9% to -83% ~ -28%), although the proportion of modern carbon in total carbon is better estimated. The CPM contribution is likely to be overestimated when the source-dependent relationship between the CPM/FPM ratio and FPM concentration is not considered. Thus, accurate knowledge of the CPM/FPM ratio, particularly for sources with high FPM concentrations, is critical to improve CPM emission estimation.

Impacts of condensable particulate matter on atmospheric organic aerosols and fine particulate matter (PM2.5) in China

Condensable particulate matter (CPM) emitted from stationary combustion and mobile sources exhibits high emissions and a large proportion of organic components. However, CPM is not generally measured when conducting emission surveys of PM in most countries, including China. Consequently, previous emission inventories have not included emission rates for CPM. Here, we construct an emission inventory of CPM in China with a focus on organic aerosols (OAs) based on collected CPM emission information. Results show that OA emissions are enhanced twofold after the inclusion of CPM in a new inventory for China for the years 2014 and 2017. Considering organic CPM emissions and model representations of secondary OA (SOA) formation from CPM, a series of sensitivity cases have been simulated here using the three-dimensional Community Multiscale Air Quality (CMAQ) model to estimate the contributions of CPM emissions to atmospheric OA and fine PM (PM2.5, particulate matter with aerodynamic diameter not exceeding 2.5 μm) concentrations in China. Compared with observations at a Beijing site during a haze episode from 14 October to 14 November 2014, estimates of the temporal average primary OA (POA) and SOA concentrations were greatly improved after including the CPM effects. These scenarios demonstrated the significant contributions of CPM emissions from stationary combustion and mobile sources to the POA (51 %-85 %), SOA (42 %-58 %), and total OA concentrations (45 %-75 %). Furthermore, the contributions of CPM emissions to total OA concentrations were demonstrated over the 2 major cities and 26 other cities of the Beijing-Tianjin-Hebei region (hereafter referred to as the "BTH2 + 26 cities") in December 2018, with average contributions of up to 49 %, 53 %, 54 %, and 50 % for Handan, Shijiazhuang, Xingtai, and Dezhou, respectively. Correspondingly, the inclusion of CPM emissions also narrowed the gap between simulated and observed PM2.5 concentrations over the BTH2 + 26 cities. These results improve the simulation performance of atmospheric OA and PM2.5 and may also provide important implications for the sources of OA.

Unit-based emissions and environmental impacts of industrial condensable particulate matter in China in 2020

The emission of condensable particulate matter (CPM) and its environmental impacts are arousing concern in China with the effective control of filter particulate matter (FPM). This study established an up-to-date and unit-based CPM emission inventory for industrial sectors and systematically evaluated the effects of CPM on primary and secondary PM_2.5 in China. In 2020, the national CPM emissions total for industrial sectors was estimated to be 0.98 Tg with uncertainty from -49% to 66%, including 0.62 Tg of organic CPM (CPM_org) and 0.36 Tg of inorganic CPM (CPM_in). Totals of 62%, 23% and 8% CPM were emitted from coal-fired power plants, coal-fired industrial boilers and sinter plants, respectively. By filling CPM emissions in PM_2.5 simulation, the normalized mean bias (NMB) of model to observation was improved from -27% to -14% in East, North and Central China. The 4 μg/m³ PM_2.5 concentration was attributed to CPM emissions in this region, accounting for 10% of observations. On "polluted" days (PM_2.5>75 μg/m³), industrial CPM emissions can contribute 7 μg/m³ PM_2.5 in North China. Therefore, China should focus on controlling CPM from coal combustion to ensure continuous air quality improvement.

Real-time detection of vehicle-originated condensable particulate matter through thermodenuder integrated aerosol measurement method at tailpipes

Condensable particulate matter (CPM) corresponds to primary particulate matter ≤2.5 μm (PM_2.5) obtained through the condensation of gaseous air pollutants caused by temperature drops in the atmosphere. The internal combustion of vehicle engines can produce CPM because of the condensable compounds in the exhaust gas. Conventional CPM measurement methods have been developed for coal-fired power plants with stable emissions through sampling and off-site analyses. They are therefore unsuitable for detecting the rapidly changing vehicle-originated CPM. In addition, the current system for evaluating PM_2.5 from vehicles, based on the particle measurement program (PMP) protocol, provides only the emission factors of total PM_2.5 (and not CPM separately) at a fixed temperature (∼25 °C) and dilution ratio (∼ × 35). This study reports, for the first time, the development of a real-time detection method for vehicle-originated CPM through a thermodenuder (TD) integrated with real-time aerosol instruments. This method was designed to reduce the loss of CPM due to condensation and diffusion while sampling the exhaust gas. It permits the investigation of the effects of dilution gas temperature (5-45 °C) and dilution ratio (up to × 30) on the formation of CPM. During the feasibility test of this method using a diesel vehicle (Euro-4), the real-time total particle number concentrations (PNs) matched well with those obtained by a PMP protocol-based evaluation system. Moreover, this method detected PNs concentrations ten times higher than the detection limit (4 × 10⁶ particles/cm³) of the PMP-based system. The emission factors of the total PM_2.5 with a bulk density (1 g/cm³) measured by this method also showed consistency with the results of the PMP protocol. The mass emission factor of CPM determined by deploying the TD was ∼14.57 mg/km (∼63% contribution to the total PM_2.5).

An online technology for effectively monitoring inorganic condensable particulate matter emitted from industrial plants

The concentration of condensable particulate matter (CPM) has gradually exceeded that of filterable particulate matter emitted from industrial plants equipped with advanced air pollution control systems. However, there is still no available online technology to measure CPM emissions. Based on the significant linear correlations (R² > 0.87, p < 3 × 10^-3) between the electrical conductivity (EC) values and ionic mass concentrations of the CPM solutions when the interference of H⁺ was excluded. We developed an online inorganic CPM monitoring system, including a cooling and condensation unit, pH and EC meters, a self-cleaning unit, and an automatic control unit. The CPM mass concentrations obtained by the developed online monitoring system agree well (mean bias 3.8-20.7%) with those obtained by the offline system according to USEPA Method 202 when used in parallel during real-world studies. Furthermore, individual ion mass concentrations of CPMs can even be retrieved separately with a time resolution of one hour when industrial plants are under steady operating conditions. The newly developed system makes the online monitoring of CPM emissions available and lays a foundation for the control of CPM emitted from industrial sources to further improve air quality.

Emission characteristics of PM2.5 and components of condensable particulate matter from coal-fired industrial plants

Particulate matter (PM), including condensable particulate matter (CPM) and filterable particulate matter (FPM), emitted from coal combustion is one of the major contributors to air pollution. In this study, CPM and FPM were sampled from two coal-fired industrial boilers with air pollution control devices (APCDs). The emission concentration of total PM (CPM and FPM) and inorganic components of CPM were studied. The organic fractions in CPM and raw coal were analyzed using a gas chromatograph/mass spectrometer (GC/MS). The concentrations of total PM in the flue gas decreased from 1475.61 to 7.68 mg/Nm³ in unit 1, and from 2451.62 to 29.38 mg/Nm³ in unit 2 after the flue gas passed through the APCDs. CPM accounted for 51.42-91.93% of total PM emitted from stacks, of which organic components (73.87-96.30%) were one of the main constituents. Although aromatic hydrocarbons are one of the major components of raw coal, they were almost nonexistent in the CPM emitted from coal combustion. Saturated hydrocarbons accounted for the largest proportion of organic components in CPM, 49.19% in unit 1 and 61.16% in unit 2. The proportion of esters in the oxygen-containing derivatives of CPM emitted from two units was relatively high. SO₄^2- was the inorganic component with the largest concentration in CPM emitted from the boiler units. This study will improve the understanding of the emissions levels of PM_2.5 and the properties of CPM that originate from the coal-fired industrial processes.

Mercury speciation and size-specific distribution in filterable and condensable particulate matter from coal combustion

Particle-bound mercury discharged with fine particulate matter from coal-fired power plants causes atmospheric pollution that impacts human health. In this study, the speciation and size-specific distribution of particle-bound mercury in filterable particulate matter (FPM) from an ultra-low emission power plant and condensable particulate matter (CPM) from an entrained flow reactor were analyzed. Most importantly, particle-bound mercury was enriched in fine particles smaller than 0.02 μm, whose mass fraction was several orders of magnitude higher than that in large particles. Particularly, HgBr₂, HgCl₂, and HgO were major mercury species in FPM, whereas CPM involves mostly HgCl₂ with a small portion of HgBr₂. The occurrence of these species was also confirmed by a thermodynamic equilibrium calculation. The results further revealed the effects of air pollution control devices (APCDs) on the speciation of particle-bound mercury. Specifically, an electrostatic precipitator (ESP) removed most particle-bound mercury. Similarly, wet flue gas desulfurization (WFGD) dramatically reduced particle-bound mercury for most particles, except those between 0.1 and 1 μm. At the outlet of WFGD, mercury bound with FPM₁₀ (smaller than 10 μm) is only 0.15% of the total mercury at the inlet of selective catalytic reduction (SCR). This knowledge provides insights that can be used to design and optimize the control strategy for mercury emission in power plants.

Considering Condensable Particulate Matter Emissions Improves the Accuracy of Air Quality Modeling for Environmental Impact Assessment

This study examines environmental impact assessment considering filterable particulate matter (FPM) and condensable particulate matter (CPM) to improve the accuracy of the air quality model. Air pollutants and meteorological data were acquired from Korea’s national monitoring station near a residential development area in the target district and background site. Seasonal emissions of PM2.5, including CPM, were estimated using the California puff (CALPUFF) model, based on Korea’s national emissions inventory. These results were compared with the traditional environmental impact assessment results. For the residential development area, the seasonal PM2.5 concentration was predicted by considering FPM and CPM emissions in the target area as well as the surrounding areas. In winter and spring, air quality standards were not breached because only FPM was considered. However, when CPM was included in the analysis, the results exceeded the air quality standards. Furthermore, it was predicted that air quality standards would not be breached in summer and autumn, even when CPM is included. In other words, conducting an environmental impact assessment on air pollution including CPM affects the final environmental decision. Therefore, it is concluded that PM2.5 should include CPM for greater accuracy of the CALPUFF model for environmental impact assessment.

Volatility Distribution of Organic Compounds in Sewage Incineration Emissions

Intermediate volatility and semivolatile organic compounds (IVOC/SVOC) are important precursors of secondary organic aerosol (SOA) while SVOC is an important contributor to primary organic aerosol (POA). However, combustion emissions data for volatility classes are limited. This study reports the gas and particle emissions that were sampled with various dilution factors from a sewage sludge incinerator burning fuel oil. Volatility distributions were determined using measurements from online mass spectrometry and offline organic compound analyses. In the low volatility organic compound (LVOC) to IVOC range, volatility bins with organic saturation concentrations of 10-100 μg m^-3 were most abundant, which was due to organic acids generated from sludge burning. Organic aerosol (OA) emission factors (EF_OA) increased 1.4 times after cooling to ambient temperatures in comparison to those of the samples from the hot stack. Upon further isothermal dilution at 25 °C, the EF_OA decreased while organic gas phase EFs increased with increasing dilution. Phase partitioning in volatility bins with saturation concentrations of 10-100 μg m^-3 was sensitive to isothermal dilution that influenced the EFs. Therefore, gas- and particle-phase measurements alone cannot constrain EFs for these volatility classes. Low dilution factors may overestimate the particle phase and underestimate the gas phase EFs compared with real-world emission conditions.

Non-Negligible Stack Emissions of Noncriteria Air Pollutants from Coal-Fired Power Plants in China: Condensable Particulate Matter and Sulfur Trioxide

In this study, we investigated the emission characteristics of condensable particulate matter (CPM) and sulfur trioxide (SO₃) simultaneously through ammonia-based/limestone-based wet flue gas desulfurization (WFGD) from four typical coal-fired power plants (CFPPs) by conducting field measurements. Stack emissions of filterable particulate matter (FPM) all meet the Chinese ultralow emission (ULE) standards, whereas CPM concentrations are prominent (even exceed 10 mg/Nm³ from two CFPPs). We find that NH₄⁺ and Cl^- increase markedly through the ammonia-based WFGD, and SO₄^2- is generally the main ionic component, both in CPM and FPM. Notably, the occurrence of elemental Se in FPM and CPM is significantly affected by WFGD. Furthermore, the established chemical profiles in FPM and CPM show a distinct discrepancy. In CPM, the elemental S mainly exists as a sulfate, and the metallic elements of Na, K, Mg, and Ca mainly exist as ionic species. Our results may indicate that not all SO₃ are included in CPM and they co-exist in stack plume. With the substantial reduction of sulfur dioxide (SO₂), S distributed in SO₃, CPM, and FPM becomes non-negligible. Finally, the emission factors of CPM and SO₃ under typical ULE technical routes fall in the ranges of 74.33-167.83 and 48.76-86.30 g/(t of coal) accordingly.

Investigation on condensable particulate matter emission characteristics in wet ammonia-based desulfurization system

Particulate matter emissions from ammonia-based wet flue gas desulfurization (Ammonia-WFGD) systems are composed of a filterable particulate matter and a condensable particulate matter (CPM) portion. However, the CPM part has been ignored for a long time, which results in an underestimation of the aerosol problems caused by Ammonia-WFGD systems. In our research, the characteristics of the CPM that emits from an Ammonia-WFGD system are investigated experimentally for the first time, with the US Environmental Protection Agency Method 202 employed as the primary measurement. The influences of some essential desulfurizing parameters are evaluated based on the experimental data. The results show that CPM contributes about 68.8% to the total particulate matter emission. CPM consists mainly of ammonium sulfates/sulfites, with the organic part accounting for less than 4%. CPM is mostly in the submicron fraction, about 71.1% of which originates from the NH₃-H₂O-SO₂ reactions. The appropriate adjustments for the parameters of the flue gas and the desulfurizing solution can inhibit CPM formation to different extents. This indicates that the parameter optimizations are promising in solving CPM emission problems in Ammonia-WFGD systems, in which the pH adjustment alone can abate CPM emission by around 49%. The opposite variations of the parameters need attention because they can cause tremendous CPM emission increase.

Evolution of Condensable Fine Particle Size Distribution in Simulated Flue Gas by External Regulation for Growth Enhancement

Condensation fine particles (CFPs) from coal-fired flue gas harm humans and the environment after being emitted into the atmosphere. Given their small size (<0.1 μm), difficulty arises in efficiently removing CFPs by wet electrostatic precipitators and mist eliminators. In this work, a laboratory apparatus was used to study the CFP growth under simulated power plant conditions. Four methods were independently investigated to increase the particle size: addition of ammonia, addition of fly ash, decreasing temperature, and applying an electrical discharge. Results demonstrated that the CFP size distribution possessed a unimodal structure with peak at 0.05 μm. At increased ammonia concentration from 10 to 30 ppm, the peak of growth factor shifted rightward and increased from 1.21 to 1.35 and the range of growth factor >1 was significantly broadened due to joint action of multiple mechanisms. Fly ash acted as the core, and CFPs adhered to the ash surface when forming ash-salt droplets. Cooling flue gas could also enhance the CFP growth due to vapor condensation. At decreased temperature from 45 to 30 °C, the median diameter of CFPs increased by 15%. Finally, the growth and agglomeration of CFPs can be further enhanced when an external electrical field was utilized. The size range of growth factor >1 can be broadened, and the peak growth factor significantly increased at 8 kV applied voltage. The research findings provide valuable guidance for effectively improving the CFP removal efficiency by external regulation for growth enhancement.

Ultrafine particles: unique physicochemical properties relevant to health and disease

Ultrafine particles (UFPs) are aerosols with an aerodynamic diameter of 0.1 µm (100 nm) or less. There is a growing concern in the public health community about the contribution of UFPs to human health. Despite their modest mass and size, they dominate in terms of the number of particles in the ambient air. A particular concern about UFPs is their ability to reach the most distal lung regions (alveoli) and circumvent primary airway defenses. Moreover, UFPs have a high surface area and a capacity to adsorb a substantial amount of toxic organic compounds. Harmful systemic health effects of PM₁₀ or PM_2.5 are often attributable to the UFP fraction. In this review, we examine the physicochemical characteristics of UFPs to enable a better understanding of the effects of these particles on human health. The characteristics of UFPs from diesel combustion will be discussed in the greatest detail because road vehicles are the primary source of UFP emissions in urban pollution hotspots. Finally, we will elaborate on the role of UFPs on global climate change, since the adverse effects of UFPs on meteorological processes and the hydrological cycle may even be more harmful to human health than their direct toxic effects.

Ultrafine particles (UFPs) from auto exhaust, factory emissions, and woodburning negatively affect human health and can alter weather patterns. UFPs, particles less than 100 nanometers, smaller than the smallest bacterium, are the most common airborne particles. Their size allows them to penetrate the deepest lung passageways, sometimes carrying toxic metals or organic compounds that trigger inflammation and disease. Hyouk-Soo Kwon at the University of Ulsan, Seoul, South Korea, and coworkers have reviewed the sources and effects of UFPs. Auto engines are a primary source; recent improvements in combustion technology have resulted in production of smaller particles, with worse effects on health. UFPs have also been found to affect cloud formation and behavior, altering rainfall patterns and potentially causing flooding or drought. Understanding the properties of UFPs will help find ways to mitigate their effects.

Migration and distribution characteristics of organic and inorganic fractions in condensable particulate matter emitted from an ultralow emission coal-fired power plant

Condensable particulate matter (CPM) is the main part of total particulate matter (TPM) discharged from coal-fired power plants. In this study, a new analytical method was proposed for accurately quantifying the organic components including n-alkanes and phthalates in CPM that sampled from an ultralow emission coal-fired plant by using the Gas Chromatography-Mass Spectrometer (GC-MS) and the mixed standard solution. The organic fraction made up 53.13%, 50.90%, 52.44% of the CPM tested at the outlet of the low-low temperature electrostatic precipitator (LLT-ESP), the wet flue gas desulfurization (WFGD) and the wet electrostatic precipitator (WESP), respectively. The total concentration of 19 kinds of n-alkanes range from 0.328 mg/Nm³ to 0.854mg/Nm³ with C₂₄-C₃₀ becoming the major n-alkanes compounds in all sampling sites. The chief component of the tested phthalate was the di-n-butyl ortho-phthalate (DBP) which comprised 95.43%, 88.29%, 95.33% of the total of five kinds of phthalates. The WFGD contributed to the reduction of phthalates and the generation of n-alkanes while the effects on WESP were opposite. Furthermore, the existing air pollution control devices (APCDs) had no significant selection for the removal of n-alkanes causing the proportions of different n-alkanes were almost the same in different sampling sites. Also, the mechanism of the APCDs on the removal of CPM organic fraction was proposed primarily. The proportion of organic components measured in the organic fractions was less than 15%. Accurate quantification of other organic compounds and the mechanism of pollutant removal should be studied in the future.

Evaluating Airborne Condensable Particulate Matter Measurement Methods in Typical Stationary Sources in China

The dry impinger method, the indirect dilution method, and the direct dilution method can be used to measure the condensable particulate matter (CPM) emissions. We tested these methods in determining the CPM emissions from typical stationary sources in China and found that the CPM concentrations measured by the dry impinger method are much higher than those measured by the two dilution methods regardless of the type of stationary source. The soluble gases (e.g., SO₂, HCl, and NH₃) partially absorbed by the impinger solutions are the main reason for the overestimation of the CPM concentrations. This is supported by detecting more water-soluble ions (e.g., SO₄^2-, Cl^-, and NH₄⁺) from the CPM collected using the dry impinger method. The positive biases of the CPM concentration and its water-soluble ions collected by the dry impinger method are larger under the conditions with high concentrations of soluble gases such as at the flue gas desulfurization inlet in coal-fired power plants. Comparing to the direct dilution method, the indirect dilution method can better capture the rapid dilution, cooling, and condensation of condensable gas precursors in the presence of filterable particulate matter and is recommended as the appropriate method for the CPM measurement in stationary sources.

Analysis of National PM2.5 (FPM and CPM) Emissions by Past, Current, and Future Energy Mix Scenarios in the Republic of Korea

The main purpose of this study was to analyze the Korean PM2.5 emissions according to the past, present, and future energy mix scenarios from 1970 to 2035, with the aim of identifying a sustainable, future environmentally friendly energy mix scenario for Korea related to PM2.5 emissions. To calculate the PM2.5 emissions according to an energy mix plan, we assumed two scenarios: (1) Scenario 1 is based on an energy conversion scenario established by the Korean government’s 7th electric power demand supply program; and (2) Scenario 2 is enhancement of fuel cell usage. In Scenario 1, filterable PM2.5 (FPM2.5) emission was calculated as 61,158 ton/year, which includes contributions of anthracite (46.8%), petroleum (39.7%), natural gas (LNG) (10.0%), and LPG (0.1%). In Scenario 2, FPM2.5 emission was calculated as 36,917 ton/year, which includes contributions of petroleum (47.8%), anthracite (40.3%), bituminous coal (10.1%), and LNG (1.7%). Thus, we concluded that the FPM2.5 mitigation effect from fuel cell policy enforcement is about 38.13% higher than the Korean national energy conversion policy. PM2.5 (FPM2.5 + condensable PM2.5 (CPM2.5)) emissions dramatically increased in both energy mix scenarios so that CPM2.5 should be considered when estimating PM2.5 emissions and PM2.5 reduction.