CF4 Adsorption on Microporous Carbons Prepared by Carbonization of Poly(vinylidene fluoride)

CF4 Capture and Separation of CF4-SF6 and CF4-N2 Fluid Mixtures Using Selected Carbon Nanoporous Materials and Metal-Organic Frameworks: A Computational Study

The adsorption of pure fluid carbon tetrafluoride and the separation of CF₄-SF₆ and CF₄-N₂ fluid mixtures using representative nanoporous materials have been investigated by employing Monte Carlo and molecular dynamics simulation techniques. The selected materials under study were the three-dimensional carbon nanotube networks, pillared graphene using carbon nanotube pillars, and the SIFSIX-2-Cu metal-organic framework. The selection of these materials was based on their previously reported efficiency to separate fluid SF₆-N₂ mixtures. The pressure dependence of the thermodynamic and kinetic separation selectivity for the CF₄-SF₆ and CF₄-N₂ fluid mixtures has therefore been investigated, to provide deeper insights into the molecular scale phenomena taking place in the investigated nanoporous materials. The results obtained have revealed that under near-ambient pressure conditions, the carbon-based nanoporous materials exhibit a higher gravimetric fluid uptake and thermodynamic separation selectivity. The SIFSIX-2-Cu material exhibits a slightly higher kinetic selectivity at ambient and high pressures.

The adsorption mechanism of CF4 on the surface of activated carbon made from peat and modified by Cu

In order to find a way to deal with CF₄ with good removal effect and easy to promote. In this study, peat was used as raw material, and copper-loaded activated carbon (Cu/AC) was successfully prepared through nitric acid oxidation and copper chloride impregnation. Compared with commercial activated carbon and widely used metal organic frameworks (MOFs), it shows a fast adsorption rate and larger adsorption capacity for CF₄. The static experiment was used to study the influence of Cu/AC on the adsorption of CF₄ in the adsorbent dosage, reaction time, temperature, and initial concentration. SEM, FTIR, XPS, XRF, and BET were used to study the changes of physical and chemical properties before and after the adsorption. It was found that the oxygen-containing group was consumed during this process. Unsaturated sites on Cu can accelerate the adsorption of CF₄, and the adsorption process is reversible. For the first time, the kinetic model, adsorption isotherm, and thermodynamic model are used to analyze the adsorption mechanism of CF₄ on the Cu/AC surface from different angles. The results show that the adsorption of CF₄ on the Cu/AC surface is a process of exothermic entropy reduction. The static adsorption process conforms to the pseudo-first-order, the pseudo-second-order, and the Freundlish adsorption model. Through 5 adsorption and desorption processes, it is found that Cu/AC has excellent recycling and recyclability performance.

Upcycling of waste polyethylene terephthalate plastic bottles into porous carbon for CF4 adsorption

Thermo-chemical processes for converting plastic wastes into useful materials are considered promising technologies to mitigate the environmental pollution caused by plastic wastes. In this study, polyethylene terephthalate (PET) plastic wastes were used to develop cost-effective and value-added porous carbons; the developed porous carbons were subsequently tested for capturing CF₄, a greenhouse gas with a high global-warming potential. The activation temperature was varied from 600 °C to 1000 °C and the mass ratio of KOH/carbon ranged from 1 to 3 in the preparation process and their effects on the textural properties and CF₄-capture performance of the PET plastic waste-derived porous carbons were investigated. The CF₄-adsorption uptake was dictated by the specific surface area and pore volume of narrow micropores less than 0.9 nm in diameter. PET-K(2)700, which was developed by KOH activation at 700 °C and KOH/carbon mass ratio of 2, showed the highest CF₄-adsorption uptake of 2.43 mmol g^-1 at 25 °C and 1 atm. Also, the CF₄-adsorption data were fitted well with the Langmuir isotherm model and pseudo second-order kinetic model. The PET plastic waste-derived porous carbons exhibited a high CF₄ uptake, good CF₄/N₂ selectivity at relatively low CF₄ pressures, easy regeneration, rapid adsorption/desorption kinetics, and excellent recyclability, which are promising for practical CF₄-capture applications.

Mesoporous Metal-Organic Frameworks with Exceptionally High Working Capacities for Adsorption Heat Transformation

Pore size is one of the most important parameters of adsorbents, and mesoporous materials have received intense attention for large guests. Here, a series of mesoporous coordination polymers underlying a new framework prototype for fast expansion of pore size is reported and the profound effect of pore size on adsorption heat transformation is demonstrated. Three isostructural honeycomb-like frameworks are designed and synthesized by combining ditopic linear metal oxalate chains and triangular tris-pyridine ligands. Changing the ligand bridging length from 5.5 to 8.6 and 9.9 Å gives rise to effective pore diameter from 20 to 33 and 37 Å, surface area from 2096 to 2630 and 2749 m² g^-1 , and pore volume from 1.19 to 1.93 and 2.36 cm³ g^-1 , respectively. By virtue of the unique and tunable isotherm shape of mesopores, exceptionally large working capacity up to 1.19 g g^-1 or 0.38 g cm^-3 for adsorption heat transformation can be achieved using R-134a (1,1,1,2-tetrafluroethane) as a working fluid.