Tailor Made Conductivities of Polymer Matrix for Thermal Management: Design and Development of Three-Dimensional Carbonaceous Nanostructures

Insights into enzymatic degradation of physically crosslinked hydrogels anchored by functionalized carbon nanofillers

Immobilization of hydrophobic enzymes on the surface of nanofillers disturbs the non-covalent interactions of polymer–filler networks and destabilizes physically crosslinked hydrogels.

Effect of Particle Orientation and Porosity on Thermal Conductivity of Petroleum Pitch Polymer-Based Carbon Molded Body

The present study was conducted to investigate changes in the thermal conductivity of petroleum pitch-based carbon molded bodies prepared by anisotropic (uniaxial) molding under different molding pressures. The carbon molded bodies were prepared using needle coke and petroleum-based binder pitch polymers (softening point: 150 ℃). Green blocks prepared under high molding pressure showed a higher particle orientation value up to 16.4 μm. Graphite blocks, prepared by graphitizing the green blocks at 2800 ℃ showed a similar trend. The pores in the carbon molded body were filled with low boiling point substances, generated by the thermal treatment of the binder pitch polymer or air that could not be discharged during the molding procedure. Therefore, when phonons encountered a pore, phonon scattering, rather than phonon transport, occurred, and thus the heat transport from the hot zone to a cold zone became slow. As a result, although the particle orientation was a little higher in the B_10-G sample than in the B_20-G sample (in the error range), the thermal conductivity was higher in the B_20-G sample, which may be because the B_10-G sample had a higher porosity than the B_20-G sample.

Understanding fluorometric interactions in ion-responsive sustainable polymer nanocomposite scaffolds

The fluorescent colour in biodegradable and biocompatible flexible polymer nanocomposite gels was modulated in order to gain insight into the interfacial interactions of functional scaffolds with metal ions. The hybrid nanomaterials were introduced into the polymer matrix to obtain mechanically robust porous morphologies where the intrinsic luminescence matrix was found to critically enhance the threshold of the visual detection limits. The quenching of fluorescence intensity has been predominantly attributed to the interactions of functional receptors of luminescent nanofillers with respect to the chromophores of the fluorescent matrix. The chromium ion is selected to understand the change in fluorescence intensity of the nanocomposite gel with the degree of metal ion adsorption. The number of functional nanomaterials loaded into the matrix and the luminescence nature of the base polymer are varied with the purpose of gaining insight into the remote sensing mechanism of the colorimetric fluorescent probe.

Microphase separation in oriented polymeric chains at the surface of nanomaterials during nanofiber formation

The presence of low-dimensional functional nanofillers during the formation of morphological phase boundaries in polymeric nanofibers by electrospinning was highlighted in this study. PAN and TPU were both selected with differential viscosities to understand the phase-segregated internal supramolecular structures on functional surfaces of different length scales. The low-dimensional carbon nanofillers displayed a significant role in the topological orientation of the polymeric chains in TPU due to the presence of hard and soft segments in the geometry of TPU. The nano-hybrid shish-kebab-type microphase separation was observed on 1D nanofillers, whereas the anisotropic hierarchical microdomains were formed in the presence of 0D nanofillers. The 2D functional surface produced highly folded nanoscale lamellae by molecular interactions with polymeric chains. By combining different dimensional nanofillers, the hybrid 1D-2D networks created multifaceted structural hierarchies with epitaxial growth on the planar surface and shish-kebab geometry on the 1D functional backbone. Our study has demonstrated the significance of the configuration of nanoscale functional surfaces on the texture of polymeric chain assemblies during electrospinning for controlled flexible scaffolds.

Enhanced Thermal Conductivity of Liquid Crystalline Epoxy Resin using Controlled Linear Polymerization

A powerful strategy to enhance the thermal conductivity of liquid crystalline epoxy resin (LCER) by simply replacing the conventional amine cross-linker with a cationic initiator was developed. The cationic initiator linearly wove the epoxy groups tethered on the microscopically aligned liquid crystal mesogens, resulting in freezing of the ordered LC microstructures even after curing. Owing to the reduced phonon scattering during heat transport through the ordered LC structure, a dramatic improvement in the thermal conductivity of neat cation-cured LCER was achieved to give a value ∼141% (i.e., 0.48 W/mK) higher than that of the amorphous amine-cured LCER. In addition, at the same composite volume fraction in the presence of a 2-D boron nitride filler, an approximately 130% higher thermal conductivity (maximum ∼23 W/mK at 60 vol %) was observed. The nanoarchitecture effect of the ordered LCER on the thermal conductivity was then examined by a systematic investigation using differential scanning calorimetry, polarized optical microscopy, X-ray diffraction, and thermal conductivity measurements. The linear polymerization of LCER can therefore be considered a practical strategy to enable the cost-efficient mass production of heat-dissipating materials, due to its high efficiency and simple process without the requirement for complex equipment.

Effect of Reinforcement at Length Scale for Polyurethane Cellular Scaffolds by Supramolecular Assemblies

This study is aimed to represent the role of carbonaceous nanofillers to reinforce the commercially available polyurethane porous structure. The effect of dimensionality of fillers to anchor the construction of stable three-dimensional (3D) cellular architectures has been highlighted. The cellular frameworks of commercially available thermoplastic polyurethane (TPU) have been fabricated through the thermoreversible supramolecular self-assembly route. It was established that the minimum shrinkage of TPU lattice structures occurred when the solid-state network is strengthened by the topologically engineered 3D hierarchical nanofillers, where the amount of reinforcement was found to play a critical role. It has been established by series of structure-property correlations that reinforcing the cellular structure to endure the capillary stress is equally effective as supercritical drying for producing low-density porous morphologies. The removal of liquid phase from gel is as important as the presence of 3D fillers in the matrix for reinforcing the cellular structures when replacing the solvent phase with air to generate a two-phase solid-gas engineered morphology. The insight into the polyurethane network structure revealed that the dimensionality, amount, and distribution of fillers in the matrix are critical for reinforcing the cellular scaffolds in solid gel without any cross-linking.

Investigation of thermal energy transport interface of hybrid graphene-carbon nanotube/polyethylene nanocomposites

It is well known the thermal properties of three-dimensional (3-D) hybrid graphene (GR)-carbon nanotube (CNT) structures are not superior to that of the individual GR and CNT, however, the 3-D hybrid GR-CNT structures can effectively improve the thermal properties of polymer matrix. Therefore, understanding the thermal energy transport in the interface between polymer matrix and 3-D hybrid GR-CNT structure is essential. Here, the enhancement mechanism of interfacial thermal transport of hybrid GR-CNT structure was explored by applying non-equilibrium molecular dynamics (NEMD) simulations. Three different types of hybrid GR-CNT structures were built. The influences of CNT radius and CNT type for the hybrid GR-CNT on the interfacial thermal properties were also analyzed. Computational results show that among the three different types of hybrid GR-CNT structures, the Model-I, i.e., the covalent bond hybrid GR-CNT structures are of the best interfacial thermal properties. Meanwhile, the CNT radius of hybrid GR-CNT structure has a great influence on the interfacial thermal properties.