Effect of Aqueous Anions on Graphene Exfoliation

Insights into the Conductive Network of Electrochemical Exfoliation with Graphite Powder as Starting Raw Material for Graphene Production

Electrochemical exfoliation starting with graphite powder as the raw material for graphene production shows superiority in cost effectiveness over the popular bulk graphite. However, the crucial conductive network inside the graphite powder electrode along with its formation and influence mechanisms remains blank. Here, an adjustable-pressure graphite powder electrode with a sandwich structure was designed for this. Appropriate encapsulation pressure is necessary and conducive to constructing a continuous and stable conductive network, but overloaded encapsulation pressure is detrimental to the exfoliation and graphene quality. With an initial encapsulation pressure (IEP) of 4 kPa, the graphite powders expand rapidly to a final stable expansion pressure of 49 kPa with a final graphene yield of 46.3%, where 84% of the graphene sheets are less than 4 layers with I_D/I_G values between 0.22 and 1.24. Increasing the IEP to 52 kPa, the expansion pressure increases to 73 kPa, but the graphene yield decreases to 39.3% with a worse graphene quality including higher layers and I_D/I_G values of 1.68-2.13. In addition, small-size graphite powders are not suitable for the electrochemical exfoliation. With the particle size decreasing from 50 to 325 mesh, the graphene yield decreases almost linearly from 46.3% to 5.5%. Conductive network and electrolyte migration synergize and constrain each other, codetermining the electrochemical exfoliation. Within an encapsulated structure, the electrochemical exfoliation of the graphite powder electrode proceeds from the outside to the inside. The insights revealed here will provide direction for further development of electrochemical exfoliation of graphite powder to produce graphene.

Appraising the potency of small molecule inhibitors and their graphene surface-mediated organizational attributes on uric acid-melamine clusters

Uric acid (UA) and melamine (MM) crystallization in humans is associated with adverse medical conditions, including the germination of kidney stones, because of their low solubility. The growth of kidney stones, usually formed on renal papillary facades, is accomplished on the matrix-coated surface by the aggregation of preformed crystals or secondary crystal nucleation. Therefore, the effects of inhibitors such as theobromine (TB) and allopurinol (AP) on MM-UA aggregation are investigated by employing classical molecular dynamics simulations on a graphene surface. This impersonates the exact essence of the precipitation of kidney stones. The interaction between MM-UA is very intense and, thus, large clusters are formed on the surface. The presence of TB and AP will, however, substantially inhibit their aggregation. TB and AP significantly impede UA aggregation in particular. Therefore, lower order UA clusters are formed. These smaller UA clusters then pull a lower number of MM towards themselves, resulting in a smaller order UA-MM cluster. MM and UA aggregation on a 2D graphene surface is found to be spontaneous. There is no difference in these molecules' adsorption with a change in the force field parameters (i.e., GAFF and OPLS-AA) for graphene. Moreover, the greater the surface area of graphene, the more molecules are absorbed. The solute-surface van der Waals interaction energy plays a driving force in the adsorption of solute molecules on the surface. In addition, interactions like hydrogen bonding and π-stacking over the graphene surface involve binding all like molecules. These aggregated solute molecules strongly attract more like molecules until all solute molecules are adsorbed on the graphene surface, as estimated by enhanced sampling. The molecular origin of graphene exfoliation by MM is also described here. The present work helps to design novel kidney stone inhibitors.

Chromatographic Approach to Isolate Exfoliated Graphene

A chromatographic approach for separating exfoliated graphene from natural flake graphite is presented. Graphene is an extremely strong, electrically and thermally conductive two-dimensional hexagonal array of carbon atoms with the potential to transform applications such as supercapacitors, composites, biosensors, ultra-thin touchscreens, and solar cells. However, many of these applications require the use of exfoliated graphene, and the current cost of this material can be prohibitive. The most cost-effective source of graphene is exfoliated graphite, and numerous approaches have been proposed for exfoliating graphite to graphene. Solution approaches are the most common, with graphite often exfoliated by extended sonication treatment followed by separation of graphene from graphite using centrifugation. This time-consuming approach results in low concentrations of small lateral dimension graphene, often in high-boiling-point organic solvents or containing stabilizers. In this study, a chromatographic approach is used in combination with a solvent interface trapping method of graphite exfoliation to isolate graphene. The interface trapping exfoliation approach uses a hydrophobic/hydrophilic solvent interface to spontaneously exfoliate graphite and form a graphene-stabilized water-in-oil emulsion. This emulsion contains both graphene and graphite, and when added to water-wet glass beads, graphene adsorbs onto the glass surface, leaving graphite in the hydrophobic mobile phase, where it is removed by washing with an additional oil phase. The efficiency of this scalable approach to separation is demonstrated by Raman spectroscopy, scanning electron microscopy, transmission electron microscopy, and Tyndall effect scattering.