Self-Organization of Soft Hydrogel Microspheres during the Evaporation of Aqueous Droplets

Evaporative self-assembly in colloidal droplets: Emergence of ordered structures from complex fluids

Colloidal droplet evaporation is an intriguing and intricate phenomenon that has captured the interest of scientists across diverse disciplines, including physical chemistry, fluid dynamics, and soft matter science, over the past two decades. Despite being a non-equilibrium system with inherent challenges posed by coffee ring formation and Marangoni effects, which hinder the precise control of deposition patterns, evaporative self-assembly presents a convenient and cost-effective approach for generating arrays of well-ordered structures and functional patterns with wide-ranging applications in inkjet printing, photonic crystals, and biochemical assays. In the realm of printed electronics and photonics, effectively mitigating coffee rings while achieving uniformity and orderliness has emerged as a critical factor in realising the next generation of large-area, low-cost, flexible devices that are exceptionally sensitive and high-performance. This review highlights the evaporative self-assembly process in colloidal droplets with a focus on the intricate mechanical environment, self-assembly at diverse interfaces, and potential applications of these assembling ordered structures.

Relationship between π-A isotherms and single microgel/microgel array structures revealed via the direct visualization of microgels at the air/water interface

The structures of single microgels and microgel arrays formed at the air/water interface were visualized directly, and their structures correlated with π-A isotherms in order to understand the compression behavior of soft and deformable microgels at this interface. Large microgels (ca. 4 μm) were synthesized so that these can be clearly visualized at the air/water interface, even under high compression, and a series of microgel compression experiments were directly evaluated using a Langmuir trough equipped with a fluorescence microscope. The experiments revealed that upon compressing the microgel arrays at the interface voids disappeared and colloidal crystallinity increased. However, the colloidal crystallinity decreased when the microgel arrays were strongly compressed. In addition, when the structures were observed at higher magnification, it became clear that the single microgel structures, when visualized from above, changed from circular to polygonal upon compressing the microgel array. The results of this study can be expected to improve the understanding of the compression behavior of microgel arrays adsorbed at the air/water interface and will thus be useful for the creation of new functional microgel stabilizers with potential applications in e.g., bubbles and emulsions.

Soft colloidal monolayers with reflection symmetry through confined drying

Colloidal monolayers serve as fundamental building blocks in fabricating diverse functional materials, pivotal for surface modifications, chemical reactivity, and controlled assembly of nanoparticles. In this article, we report the formation of colloidal monolayers generated by drying an aqueous droplet containing soft colloids confined between two hydrophilic parallel plates. The analysis of the kinetics of evaporation in this confined mode showed that: (i) for a significant portion of the drying time, the drops adopt a catenoid configuration; (ii) in the penultimate stage of drying, the catenoid structure undergoes division into two daughter droplets; (iii) the three-phase contact line remains pinned at a specific location while it continuously slips at all other locations. The interplay between interface-assisted particle deposition onto the solid substrate and the time evolution of particle concentration within the droplet during evaporation results in unique microstructural features in the deposited patterns. Notably, these deposit patterns exhibit reflection symmetry. The microstructural features of the dried deposits are further quantified by calculating the particle number density, inter-particle separation, areal disorder parameter, and bond orientational order parameter. The variation of these parameters for deposits formed under different conditions, such as by altering the spacing between parallel plates and the concentration of microgel particles in the droplet, is discussed.

Multi-layer core/shell microgels with internal complexity and their nanocomposites

In this study, we show that core/shell (CS) microgels with multiple layers can be created via a one-pot precipitation polymerization, in which monomers are added to the reaction flask multiple times once most of the previous monomer has been consumed. The complex internal structures of the microgels were examined using a combination of scattering and microscopy techniques.

The compression of deformed microgels at an air/water interface

The compression of deformed hydrogel microspheres (microgels) at air/water interfaces was investigated using a Langmuir-Blodgett trough with simultaneous in situ visualization of the process using a fluorescent microscope. The relationship between the structure of the microgel arrays and the compression behavior was clarified using microgels with different degrees of crosslinking.

Drying of bio-colloidal sessile droplets: Advances, applications, and perspectives

Drying of biologically-relevant sessile droplets, including passive systems such as DNA, proteins, plasma, and blood, as well as active microbial systems comprising bacterial and algal dispersions, has garnered considerable attention over the last decades. Distinct morphological patterns emerge when bio-colloids undergo evaporative drying, with significant potential in a wide range of biomedical applications, spanning bio-sensing, medical diagnostics, drug delivery, and antimicrobial resistance. Consequently, the prospects of novel and thrifty bio-medical toolkits based on drying bio-colloids have driven tremendous progress in the science of morphological patterns and advanced quantitative image-based analysis. This review presents a comprehensive overview of bio-colloidal droplets drying on solid substrates, focusing on the experimental progress during the last ten years. We provide a summary of the physical and material properties of relevant bio-colloids and link their native composition (constituent particles, solvent, and concentrations) to the patterns emerging due to drying. We specifically examined the drying patterns generated by passive bio-colloids (e.g., DNA, globular, fibrous, composite proteins, plasma, serum, blood, urine, tears, and saliva). This article highlights how the emerging morphological patterns are influenced by the nature of the biological entities and the solvent, micro- and global environmental conditions (temperature and relative humidity), and substrate attributes like wettability. Crucially, correlations between emergent patterns and the initial droplet compositions enable the detection of potential clinical abnormalities when compared with the patterns of drying droplets of healthy control samples, offering a blueprint for the diagnosis of the type and stage of a specific disease (or disorder). Recent experimental investigations of pattern formation in the bio-mimetic and salivary drying droplets in the context of COVID-19 are also presented. We further summarized the role of biologically active agents in the drying process, including bacteria, algae, spermatozoa, and nematodes, and discussed the coupling between self-propulsion and hydrodynamics during the drying process. We wrap up the review by highlighting the role of cross-scale in situ experimental techniques for quantifying sub-micron to micro-scale features and the critical role of cross-disciplinary approaches (e.g., experimental and image processing techniques with machine learning algorithms) to quantify and predict the drying-induced features. We conclude the review with a perspective on the next generation of research and applications based on drying droplets, ultimately enabling innovative solutions and quantitative tools to investigate this exciting interface of physics, biology, data sciences, and machine learning.

Triple-line dynamics of a soft colloid-laden drop on a hydrophobic surface

Evaporation of fluid from a pinned drop placed on solid surface proceeds via constant contact radius (CCR) mode, with a continuous reduction in the contact angle. The reduction of contact angle leads to an imbalance of interfacial tensions at the three-phase contact line. When the unbalanced force is sufficiently strong, the drop slips from the pinned contact line and slides inward. Depinning of the drop alters the mode of evaporation to constant contact angle (CCA) mode till it repins onto the surface. The change in evaporation mode from CCR to CCA is usually achieved by tuning the pinning energy barrier by controlling the surface properties of the substrate. Here, we demonstrate that the evaporation mode can be controlled by solely tailoring the surface tension of the drop, which is achieved in microgel particle-laden sessile drops that show spontaneous adsorption of microgels to the air/water interface, leading to a decrease in the interfacial tension. We show that droplets containing a sufficient number of microgels evaporate predominantly in CCR mode even on a hydrophobic surface, and the contact line remains pinned throughout the evaporation of the drop. Interestingly, the contact line dynamics can be controlled by tuning the softness of the microgels and the particle concentration in the drops.

Harnessing the polymer-particle duality of ultra-soft nanogels to stabilise smart emulsions

Micro- and nanogels are widely used to stabilise emulsions and simultaneously implement their responsiveness to the external stimuli. One of the factors that improves the emulsion stability is the nanogel softness. Here, we study how the softest nanogels that can be synthesised with precipitation polymerisation of N-isopropylacrylamide (NIPAM), the ultra-low crosslinked (ULC) nanogels, stabilise oil-in-water emulsions. We show that ULC nanogels can efficiently stabilise emulsions already at low mass concentrations. These emulsions are resistant to droplet flocculation, stable against coalescence, and can be easily broken upon an increase in temperature. The resistance to flocculation of the ULC-stabilised emulsion droplets is similar to the one of emulsions stabilised by linear pNIPAM. In contrast, the stability against coalescence and the temperature-responsiveness closely resemble those of emulsions stabilised by regularly crosslinked pNIPAM nanogels. The reason for this combination of properties is that ULC nanogels can be thought of as colloids in between flexible macromolecules and particles. As a polymer, ULC nanogels can efficiently stretch at the interface and cover it uniformly. As a regularly crosslinked nanogel particle, ULC nanogels protect emulsion droplets against coalescence by providing a steric barrier and rapidly respond to changes in external stimuli thus breaking the emulsion. This polymer-particle duality of ULC nanogels can be exploited to improve the properties of emulsions for various applications, for example in heterogeneous catalysis or in food science.

Fluid interface-assisted assembly of soft microgels: recent developments for structures beyond hexagonal packing

Microgels adsorb to air/water and oil/water interfaces - a process driven by a significant reduction in interfacial tension. Depending on the available interface area per microgel, strong lateral deformation can be observed. Typically, hexagonally ordered structures appear spontaneously upon contact of the microgel shells. Transfer from the interface to solid substrates gives access to macroscopically sized microgel monolayers that are interesting for photonic and plasmonic studies as well as colloid-based lithography, for example. Significant efforts have been made to understand the phase behavior of microgels at different interfaces and to explore the available parameter space for achieving complex tessellations. In this review, we will discuss the most recent developments in the realization of microgel monolayers with structures beyond hexagonal packing.

A scaling law of particle transport in inkjet-printed particle-laden polymeric drops

Hydrogels with embedded functional particulates are widely used to create soft materials with innovative functionalities. In order to advance these soft materials to functional devices and machines, critical technical challenges are the precise positioning of particulates within the hydrogels and the construction of the hydrogels into a complex geometry. Inkjet printing is a promising method for addressing these challenges and ultimately achieving hydrogels with voxelized functionalities, so-called digital hydrogels. However, the development of the inkjet printing process primarily relies on empirical optimization of its printing and curing protocol. In this study, a general scaling law is proposed to predict the transport of particulates within the hydrogel during inkjet printing. This scaling law is based on a hypothesis that water-matrix interaction during the curing of inkjet-printed particle-laden polymeric drops determines the intra-drop particle distribution. Based on the hypothesis, a dimensionless similarity parameter of the water-matrix interaction is proposed, determined by the hydrogel's water evaporation coefficient, particle size, and mechanical properties. The hypothesis was tested by correlating the intra-drop particle distribution to the similarity parameter. The results confirmed the scaling law capable of guiding ink formulation and printing and curing protocol.

How Softness Matters in Soft Nanogels and Nanogel Assemblies

Softness plays a key role in determining the macroscopic properties of colloidal systems, from synthetic nanogels to biological macromolecules, from viruses to star polymers. However, we are missing a way to quantify what the term "softness" means in nanoscience. Having quantitative parameters is fundamental to compare different systems and understand what the consequences of softness on the macroscopic properties are. Here, we propose different quantities that can be measured using scattering methods and microscopy experiments. On the basis of these quantities, we review the recent literature on micro- and nanogels, i.e. cross-linked polymer networks swollen in water, a widely used model system for soft colloids. Applying our criteria, we address the question what makes a nanomaterial soft? We discuss and introduce general criteria to quantify the different definitions of softness for an individual compressible colloid. This is done in terms of the energetic cost associated with the deformation and the capability of the colloid to isotropically deswell. Then, concentrated solutions of soft colloids are considered. New definitions of softness and new parameters, which depend on the particle-to-particle interactions, are introduced in terms of faceting and interpenetration. The influence of the different synthetic routes on the softness of nanogels is discussed. Concentrated solutions of nanogels are considered and we review the recent results in the literature concerning the phase behavior and flow properties of nanogels both in three and two dimensions, in the light of the different parameters we defined. The aim of this review is to look at the results on micro- and nanogels in a more quantitative way that allow us to explain the reported properties in terms of differences in colloidal softness. Furthermore, this review can give researchers dealing with soft colloids quantitative methods to define unambiguously which softness matters in their compound.

Durable gelfoams stabilized by compressible nanocomposite microgels

Compressible nanocomposite microgels can stabilize the air/water interfaces of gas bubbles for several months, which affords durable gelfoams.

Evaporative self-assembly of soft colloidal monolayers: the role of particle softness

We investigate the sessile drop evaporation aided self-assembly of microgel particles by varying their softness. Evaporation of sessile drops containing amphiphilic microgel particles at suitable concentrations results in uniform monolayer deposits that span the entire drop area. At lower concentrations, the deposits are in the form of monolayer coffee rings whose width scales with particle concentration. Using softer microgels synthesised with a lower quantity of crosslinker, we show that the monolayer coffee rings do not form at low particle concentrations. The microgels adsorbed at the interface deform, and the extent of deformation depends on the softness of the microgels as well as their concentration at the interface. Upon complete evaporation of the solvent, the microgel-laden interface is transferred to the substrate. The final deposit shows hexagonal particle arrays where the interparticle separation increases with increasing microgel softness and decreases with particle concentration in the drop. Further insight into the role of microgel softness in the microstructure of the particulate deposits is obtained by measuring the viscoelasticity of the particle-laden interface. Interestingly, the interface loaded with lesser crosslinked microgels exhibits viscoelastic nature even at lower particle concentrations, whereas the higher crosslinked microgels show viscous behaviour.

Programming Colloidal Self-Assembled Patterns (cSAPs) into Thermo-Responsible Hybrid Surfaces for Controlling Human Stem Cells and Macrophages

Hybrid surfaces with tunable topography, chemistry, and stiffness have potential to rebuild native extracellular matrix (ECM) and manipulate cell behavior in vitro. However, the fabrication of controllable hybrid surfaces is still challenging. In this study, colloidal self-assembly technology was used to program particles into highly ordered structures with hybrid chemistry and stiffness at biointerfaces. These colloidal self-assembled patterns (cSAPs), including unary, binary, and ternary cSAPs, composed of silicon (Si), polystyrene (PS), and/or poly(N-isopropylacrylamide) (pNIPAM) nanogels (PNGs), were fabricated using either coassembly or layer-by-layer (LBL) methods. The selected binary cSAPs (i.e., PS/PNG and PNG/PS) have a tunable surface topography and wettability between 25 and 37 °C; thus, they can be used as dynamic cell culture substrates. Human adipose-derived mesenchymal stem cells (hASCs), bone marrow-derived mesenchymal stem cells (hBMSCs), and macrophages (THP-1) were investigated on these hybrid cSAPs under a static or dynamic system. The results showed that hybrid cSAPs significantly influenced the focal adhesions, cell morphology, cell migration, and gene expressions of stem cells. In general, stem cells had more vinculin puncta, smaller spreading size, and faster migration speed than the TCPS control. Hybrid cSAPs up-regulated gene expressions of focal adhesion kinase (FAK) and chondrocytes (AGG and SOX9) under static culture, while they also up-regulated osteocytes (COL1 and RUNX2) under dynamic culture. THP-1 macrophages were at M0 state on all cSAPs under static culture. However, cells became sensitive under dynamic culture. For example, some M1 genes (i.e., IL6, CD68, and TNFα) and M2 genes (i.e., IL10 and CD206) were down-regulated, while other M1 genes (i.e., IL1β) and M2 genes (i.e., TGF-β and IL1ra) were up-regulated, depending on the particle combinations. In conclusion, new hybrid cSAPs with thermoresponsive surface properties are versatile materials for stem cells and macrophages manipulation.

Non-close-packed arrangement of soft elastomer microspheres on solid substrates

Unlike rigid microparticles, soft and deformable elastomer (rubber) microspheres were found to exhibit a non-close-packed arrangement on solid substrates after the evaporation of water from their dispersions. The microscopic observation revealed that individual microspheres are ordered in regular intervals at the air/water interface of a sessile droplet and remain fixed on the substrate without being affected by the capillary forces during evaporation due to their deformability. Moreover, using the Langmuir-Blodgett method, thin films of non-close-packed structures could be successfully generated over large areas. Our findings may potentially help to control the arranged structures of elastomer microspheres, which can be expected to improve the nano-science and technology for the precise control for e.g. surface patterning.

Nanostructure and thermoresponsiveness of poly(N-isopropyl methacrylamide)-based hydrogel microspheres prepared via aqueous free radical precipitation polymerization

Thermoresponsive hydrogel microspheres (microgels) are smart materials that quickly respond to external stimuli, and their thermoresponsiveness can be tuned by varying the constituent chemical species. Although uniformly sized microgels can be prepared via aqueous free radical precipitation polymerization, the nanostructure of the obtained microgels is complex and remains unclear so far. In the present study, the nanostructure and thermoresponsiveness of poly(N-isopropyl methacrylamide) (pNIPMAm)-based microgels, which have a volume-transition temperature of ∼43 °C, were evaluated mainly using temperature-controllable high-speed atomic force microscopy. These observations, which are characterized by high spatio-temporal resolution, revealed that the pNIPMAm microgels have a peculiar heterogeneous structure, for example a core-shell and non-thermoresponsive nanostructure in the core region, that originates from the precipitation polymerization process. Furthermore, it was found that the adsorption concentration of the microgels on the substrate is one of the keys for controlling their thermoresponsiveness. These findings can be expected to advance the design of new materials such as thermoresponsive nanosheets and stimuli-responsive coatings.

On Going to a New Era of Microgel Exhibiting Volume Phase Transition

The discovery of phenomena of volume phase transition has had a great impact not only on bulk gels but also on the world of microgels. In particular, research on poly(N-isopropylacrylamide) (PNIPAM) microgels, whose transition temperature is close to body temperature, has made remarkable progress in almost 35 years. This review presents some breakthrough findings in microgels that exhibit volume phase transitions and outlines recent works on the synthesis, structural analysis, and research direction of microgels.

Precise regulation of particle size of poly(N-isopropylacrylamide) microgels: Measuring chain dimensions with a "molecular ruler"

HYPOTHESIS

Poly(N-isopropylacrylamide) microgels are used extensively in the design of drug carriers, surfaces for control of cell adhesion, and optical devices. Particle size is a key factor and has a significant influence in many areas.

EXPERIMENTS

In this work, precise control of the particle size of poly(N-isopropylacrylamide) microgels was achieved by controlling the separation distance of the poly(N-isopropylacrylamide) chains. Dibromoalkanes of different size were used as an adjustable "molecular ruler" to measure molecular dimensions in poly(N-isopropylacrylamide) nanoaggregates at the critical crosslinking temperature.

FINDINGS

We find that the chain separation distance decreases as the temperature increases with a sharp decrease over the 55-to-65 °C interval. Based on the observed relationships between chain separation and crosslinker, the particle size of poly(N-isopropylacrylamide) microgels can be regulated by changing the length of the "molecular ruler" (crosslinker) at the same temperature. Furthermore, for partly crosslinked poly(N-isopropylacrylamide) microgels that contain free crosslinkable sites, the particle size can be reduced still more by further crosslinking ("re-crosslinking") with crosslinkers of different size. It is shown that the particle size can be regulated by adjusting the length of "molecular ruler" and the degree of crosslinking. This work provides a "molecular level" method for precise control of poly(N-isopropylacrylamide) microgel particle size.

Stimuli-Responsive Behavior of PNiPAm Microgels under Interfacial Confinement

The volume phase transition of microgels is one of the most paradigmatic examples of stimuli-responsiveness, enabling a collapse from a highly swollen microgel state into a densely coiled state by an external stimulus. Although well characterized in bulk, it remains unclear how the phase transition is affected by the presence of a confining interface. Here, we demonstrate that the temperature-induced volume phase transition of poly(N-isopropylacrylamide) microgels, conventionally considered an intrinsic molecular property of the polymer, is in fact largely suppressed when the microgel is adsorbed to an air/liquid interface. We further observe a hysteresis in the core morphology and interfacial pressure between heating and cooling cycles. Our results, supported by molecular dynamics simulations, reveal that the dangling polymer chains of microgel particles, spread at the interface under the influence of surface tension, do not undergo any volume phase transition. The balance in free energy responsible for the volume phase transition is fundamentally altered by interfacial confinement. These results imply that important technological properties of such systems, including the temperature-induced destabilization of emulsions, do not occur via a decrease in the interfacial coverage of the microgels.

Effect of Charge Groups Immobilized in Hydrogel Microspheres during the Evaporation of Aqueous Sessile Droplets

In contrast to conventional dispersions of solid microspheres, dilute dispersions containing soft hydrogel microspheres (microgels) exhibit unique drying behavior due to their selective adsorption at the air/water interface of sessile droplets. So far, the impact of the size, chemical composition, and softness (degree of cross-linking) of microgels has been investigated. In the present study, we present the impact of charged groups introduced in the microgels on the adsorption and assembly behavior of these microgels at the air/water interface using a series of microgels with different amounts and distribution of charged groups. A series of experiments under different conditions (pH value and ionic strength) afforded information that clarified the adsorption, interpenetration, and deformation behavior of such charged microgels at the air/water interface. The results indicate that the adsorption and the deformation of charged microgels at the air/water interface are suppressed by the presence of charged groups. Moreover, charged microgels adsorbed at the interface are more dynamic and not highly entangled with each other; i.e., even though the more dynamic charged microgels are arranged at the interface, these arranged structures are disrupted upon transferring onto the solid substrates. Our findings of this study can be expected to promote the further development of applications, e.g., foams and emulsions stabilized by microgels, that crucially requires an in-depth understanding of the adsorption behavior of charged microgels at the air/water interface such as coatings.

Concentration dependence of the dynamics of microgel suspensions investigated by dynamic light scattering

The dynamics of colloidal gel particle suspensions, i.e., microgel suspensions, has been investigated by dynamic light scattering (DLS) over a wide concentration range from the (I) dilute (φ < φcp) to the (II) intermediate (φ ≈ φcp) and (III) high concentration regions (φ ≫ φcp), where φ and φcp are the volume fraction of the gel particles in the suspension and the random close packing fraction, φcp ≈ 0.64, respectively. The time-intensity correlation function exhibited a distinct change with increasing φ, i.e., from ergodic behaviour (region I and II) to nonergodic behaviour (region III). A mode transition from translational (region I) to cooperative diffusion (the so-called gel mode) (region II) was also observed due to the soft and deformable nature of the microgels. Different from the dynamics of hard colloidal glass suspensions, the gel mode remained even at φ ≫ φcp. By using the ensemble-averaged time-correlation function, IE, we quantify the relationship between φ and their dynamics, and show that the soft microgels are deswollen in the densely packed state.

Hydrogel Microellipsoids that Form Robust String-Like Assemblies at the Air/Water Interface

Soft colloidal particles such as hydrogel microspheres assemble at air/water or oil/water interfaces, where the soft colloids are highly deformed and their surface polymer chains are highly entangled with each other. Herein, we report the formation of robust one-dimensional, string-like colloidal assemblies through self-organization of hydrogel microspheres with shape anisotropy at the air/water interface of sessile droplets. Shape-anisotropic hydrogel microspheres were synthesized via two-step polymerization, whereby a hydrogel shell was formed onto preformed rigid microellipsoids. The shape anisotropy of the hydrogel microspheres was confirmed by transmission electron microscopy and high-speed atomic force microscopy as well as by light-scattering measurements. The present findings are crucial for the understanding of natural self-organization phenomena, where "softness" influences microscopic assembled structures such as those of Nostoc bacteria.

Non-Thermoresponsive Decanano-sized Domains in Thermoresponsive Hydrogel Microspheres Revealed by Temperature-Controlled High-Speed Atomic Force Microscopy

Despite the tremendous efforts devoted to the structural analysis of hydrogel microspheres (microgels), many details of their structures remain unclear. Reported in this study is that thermoresponsive poly(N-isopropyl acrylamide) (pNIPAm)-based microgels exhibit not only the widely accepted core-shell structures, but also inhomogeneous decanano-sized non-thermoresponsive spherical domains within their dense cores, which was revealed by temperature-controlled high-speed atomic force microscopy (TC-HS-AFM). Based on a series of experiments, it is concluded that the non-thermoresponsive domains are characteristic for pNIPAm microgels synthesized by precipitation polymerization, and plausible structures for microgels prepared by other polymerization techniques are proposed.

Nanogels and Microgels: From Model Colloids to Applications, Recent Developments, and Future Trends

Nanogels and microgels are soft, deformable, and penetrable objects with an internal gel-like structure that is swollen by the dispersing solvent. Their softness and the potential to respond to external stimuli like temperature, pressure, pH, ionic strength, and different analytes make them interesting as soft model systems in fundamental research as well as for a broad range of applications, in particular in the field of biological applications. Recent tremendous developments in their synthesis open access to systems with complex architectures and compositions allowing for tailoring microgels with specific properties. At the same time state-of-the-art theoretical and simulation approaches offer deeper understanding of the behavior and structure of nano- and microgels under external influences and confinement at interfaces or at high volume fractions. Developments in the experimental analysis of nano- and microgels have become particularly important for structural investigations covering a broad range of length scales relevant to the internal structure, the overall size and shape, and interparticle interactions in concentrated samples. Here we provide an overview of the state-of-the-art, recent developments as well as emerging trends in the field of nano- and microgels. The following aspects build the focus of our discussion: tailoring (multi)functionality through synthesis; the role in biological and biomedical applications; the structure and properties as a model system, e.g., for densely packed arrangements in bulk and at interfaces; as well as the theory and computer simulation.

The multiple roles of carbonic anhydrase in calcium carbonate mineralization

Carbonic anhydrase (CA) accelerates, templates and arrests calcium carbonate mineralization by playing both enzymatic and structural protein roles.