Sequence Effects on the Salt-Enhancement Behavior of Polyelectrolytes Adsorption

Adsorption of polyelectrolytes in the presence of varying dielectric discontinuity between solution and substrate

We examine the interactions between polyelectrolytes (PEs) and uncharged substrates under conditions corresponding to a dielectric discontinuity between the aqueous solution and the substrate. To this end, we vary the relevant system characteristics, in particular the substrate dielectric constant ɛs under different salt conditions. We employ coarse-grained molecular dynamics simulations with rodlike PEs in salt solutions with explicit ions and implicit water solvent with dielectric constant ɛw = 80. As expected, at low salt concentrations, PEs are repelled from the substrates with ɛs < ɛw but are attracted to substrates with a high dielectric constant due to image charges. This attraction considerably weakens for high salt and multivalent counterions due to enhanced screening. Furthermore, for monovalent salt, screening enhances adsorption for weakly charged PEs, but weakens it for strongly charged ones. Meanwhile, multivalent counterions have little effect on weakly charged PEs, but prevent adsorption of highly charged PEs, even at low salt concentrations. We also find that correlation-induced charge inversion of a PE is enhanced close to the low dielectric constant substrates, but suppressed when the dielectric constant is high. To explore the possibility of a PE monolayer formation, we examine the interaction of a pair of like-charged PEs aligned parallel to a high dielectric constant substrate with ɛs = 8000. Our main conclusion is that monolayer formation is possible only for weakly charged PEs at high salt concentrations of both monovalent and multivalent counterions. Finally, we also consider the energetics of a PE approaching the substrate perpendicular to it, in analogy to polymer translocation. Our results highlight the complex interplay between electrostatic and steric interactions and contribute to a deeper understanding of PE-substrate interactions and adsorption at substrate interfaces with varying dielectric discontinuities from solution, ubiquitous in biointerfaces, PE coating applications, and designing adsorption setups.

Relative Strength of Polycation Adsorption on Oxide Surfaces

Polyelectrolyte adsorption onto surfaces is widely employed in water treatment and mining. However, little is known of the relative interaction strengths between surfaces and polymer. This fundamental property is assumed to be dominated by electrostatics, i.e., attractive interactions between opposite charges, which are set by the overall ionic strength ("salt concentration") of the solution, and charge densities of the surface and the polymer. A common, counterintuitive finding is a range of salt concentrations over which the amount of adsorbed polyelectrolyte increases as electrostatic interactions are tempered by the addition of salt. After an adsorption maximum, higher salt concentrations then produce the expected gradual desorption of polyelectrolyte. In this work, the salt response of the adsorption of the same narrow molecular weight distribution polycation, poly(N-methyl-4-vinylpyridinium), PM4VP, to a variety of surfaces was explored. Oxide powders for adsorption included Al2O3, SiO2, Fe2O3, Fe3O4, TiO2, ZnO, and CuO. Planar surfaces included silicon wafers, mica, calcium carbonate, and CaF2 single crystals. The PM4VP was radiolabeled with 14C so that sensitive, submonolayer amounts could be detected. The position of the peak maximum, or the lack of a peak, in response to added salt was used to rank the electrostatic component of the interaction. The importance of charge regulation, a shift in the surface pKa in response to solution species, was highlighted as a mechanism for adsorption on the "wrong" side of the isoelectric point and also as a factor contributing to the difficulty of reaching the totally desorbed state even at the highest salt concentrations.

Investigating the Sequence Specific Adsorption Behavior of Polypeptides at the Solid/Liquid Interface

Polymer adsorption at the solid/liquid interface depends not only on the chemical composition of the polymer but also on the specific placement of the monomers along the polymer sequence. However, challenges in designing polymers with well-controlled sequences have limited explorations into the role of polymer sequence on adsorption behavior to molecular simulations. Here, we demonstrate how the sequence control offered by polypeptide synthesis can be utilized to study the effects small changes in polymer sequence have on polymer adsorption behavior at the solid/liquid interface. Through a combination of quartz crystal microbalance with dissipation monitoring and total internal reflection ellipsometry, we study the adsorption behavior of three polypeptides, consisting of 90% lysine and 10% cysteine, onto a gold surface. We find different mechanisms are responsible for the adsorption of polypeptides and the resulting conformation on the surface. The initial adsorption of the polypeptides is driven by electrostatic interactions between the polylysine and the gold surface. Once adsorbed, the cysteine undergoes a thiol-Au reaction with the surface, altering the conformation of the polymer layer. Our findings suggest the conformation of the polypeptide layer is dependent on the placement of the cysteines within the sequence; polypeptide chains with evenly spaced cysteine groups adopt a more tightly bound "train" conformation as compared to polypeptides with closely grouped cysteine groups. We envision that the methodologies presented here to study sequence specific adsorption behaviors using polypeptides could be a valuable tool to complement molecular simulations studies.