Structurally Well-Defined Anion Conductive Aromatic Copolymers: Effect of the Side-Chain Length

Cross-Linked Anion-Exchange Membranes with Dipole-Containing Cross-Linkers Based on Poly(terphenyl isatin piperidinium) Copolymers

To balance the ionic conductivity and dimensional stability of anion-exchange membranes (AEMs), several cross-linked ether-free poly(terphenyl isatin piperidinium) copolymers were synthesized using 1,2-bis(2-aminoethoxy)ethane as a cross-linker. By introducing an alkyl diamine-based hydrophobic cross-linker as a control, the effects of the dipolar-molecule-containing cross-linker on the comprehensive performance of the membranes were investigated. Cation-dipole interactions between the cations and the hydrophilic ethylene oxide cross-linker enhance the self-assembly capability of the cationic groups. The introduction of the rotatable ethylene oxide cross-linker facilitates the flexibility of the cross-linked networks, thereby promoting hydrophilic/hydrophobic phase separation and inhibiting excessive swelling of the corresponding AEMs simultaneously. The resulting PTPBHIN-O₁₉ membrane showed a high hydroxide conductivity (151.69 mS cm^-1) and low swelling ratio (10.53%) at 80 °C. Furthermore, owing to the cross-linked structure and ether-free polymer backbone with high alkali resistance, the membranes treated in 3 M NaOH at 80 °C for 1600 h maintained ≥85% of their hydroxide conductivity, indicating excellent alkaline stability. A H₂/O₂ fuel cell based on the PTPBHIN-O₁₉ AEM exhibited a maximum power density of 398 mW cm^-2 at 515 mA cm^-2.

Alkaline Stability Evaluation of Polymerizable Hexyl-Tethered Ammonium Cations

One of the important challenges in designing robust alkaline anion exchange membranes is the difficulty associated with the chemical stability of covalently bound cationic units. Here, a systematic study exploring alkaline stabilities of polymerizable hexyltrimethylammonium cations is presented, where the hexyl chain is linked to a phenyl ring through a direct carbon-carbon, phenyl ether, or benzyl ether functionality. For this work, small molecule model compounds, styrenic monomer analogs, and their homopolymers are synthesized. Alkaline stabilities of the small molecule cations and their homopolymers are compared to alkaline stability of benzyltrimethylammonium (BTMA) cation and its homopolymer poly(BTMA), respectively. All the hexyl-tethered cations and their homopolymers are significantly more stable under strongly alkaline conditions (2 m KOD at 80 °C). Moreover, ether-linked cations show comparable stability to the direct carbon-carbon linked cation. Via ¹ H NMR analyses, possible degradation mechanisms are investigated for each small molecule cation. Findings of this study strongly suggest that the alkaline stability is dictated by the steric hindrance around the β-hydrogen. This study expands beyond the limits of general knowledge on alkaline stability of alkyl-tethered ammonium cations via the Hofmann elimination route, highlights important design parameters for stable ammonium cations, and demonstrates accessible directly polymerizable alkaline stable ammonium cations.

A highly stable aliphatic backbone from visible light-induced RAFT polymerization for anion exchange membranes

A novel strategy that exploits “visible light-induced RAFT” is presented for fabricating alkaline stable AEMs with fully aliphatic backbones.

Functionalizing Polystyrene with N-Alicyclic Piperidine-Based Cations via Friedel-Crafts Alkylation for Highly Alkali-Stable Anion-Exchange Membranes

Different anion-exchange membranes (AEMs) based on polystyrene (PS)-carrying benzyltrimethyl ammonium cations are currently being developed for use in alkaline fuel cells and water electrolyzers. However, the stability in relation to these state-of-the-art cations needs to be further improved. Here, we introduce highly alkali-stable mono- and spirocyclic piperidine-based cations onto PS by first performing a superacid-mediated Friedel-Crafts alkylation using 2-(piperidine-4-yl)propane-2-ol. This is followed by quaternization of the piperidine rings either using iodomethane to produce N,N-dimethyl piperidinium cations or by cyclo-quaternizations using 1,5-dibromopentane and 1,4-dibromobutane, respectively, to obtain N-spirocyclic quaternary ammonium cations. Thus, it is possible to functionalize up to 27% of the styrene units with piperidine rings and subsequently achieve complete quaternization. The synthetic approach ensures that all of the sensitive β-hydrogens of the cations are present in ring structures to provide high stability. AEMs based on these polymers show high alkaline stability and less than 5% ionic loss was observed by 1H NMR spectroscopy after 30 days in 2 M aq NaOH at 90 °C. AEMs functionalized with N,N-dimethyl piperidinium cations show higher stability than the ones carrying N-spirocyclic quaternary ammonium. Careful analysis of the latter revealed that the rings formed in the cyclo-quaternization are more prone to degrade via Hofmann elimination than the rings introduced in the Friedel-Crafts reaction. AEMs with an ion-exchange capacity of 1.5 mequiv g-1 reach a hydroxide conductivity of 106 mS cm-1 at 80 °C under fully hydrated conditions. The AEMs are further tuned and improved by blending with polybenzimidazole (PBI). For example, an AEM containing 2 wt % PBI shows reduced water uptake and much improved robustness during handling and reaches 71 mS cm-1 at 80 °C. The study demonstrates that the critical alkaline stability of PS-containing AEMs can be significantly enhanced by replacing the benchmark benzyltrimethyl ammonium cations with N-alicyclic piperidine-based cations.

Highly Conductive and Water-Swelling Resistant Anion Exchange Membrane for Alkaline Fuel Cells

To ameliorate the trade-off effect between ionic conductivity and water swelling of anion exchange membranes (AEMs), a crosslinked, hyperbranched membrane (C-HBM) combining the advantages of densely functionalization architecture and crosslinking structure was fabricated by the quaternization of the hyperbranched poly(4-vinylbenzyl chloride) (HB-PVBC) with a multiamine oligomer poly(N,N-Dimethylbenzylamine). The membrane displayed well-developed microphase separation morphology, as confirmed by small angle X-ray scattering (SAXS) and transmission electron microscopy (TEM). Moreover, the corresponding high ionic conductivity, strongly depressed water swelling, high thermal stability, and acceptable alkaline stability were achieved. Of special note is the much higher ratio of hydroxide conductivity to water swelling (33.0) than that of most published side-chain type, block, and densely functionalized AEMs, implying its higher potential for application in fuel cells.

Effect of Micromorphology on Alkaline Polymer Electrolyte Stability

Recent studies demonstrated that the chemical stability of alkaline polymer electrolytes (APEs) could be improved by reducing the inductive effect between cations and backbones. Therefore, pendent cations were recommended. However, microphase-separated morphologies would be generated by elongating the spacer between cations and backbones, which have a significant influence on the chemical stability of APEs too. In order to analyze how the patterns of micromorphology affect the chemical stability of the materials, in the present work, four APEs ( a₁-QAPS, a₃-QAPS, a₅-QAPS, and a₇-QAPS) with different lengths of side chain between polysulfone and quaternary ammonium are synthesized. The longer the side chain is, the more obvious the microphase separation for the a _x-QAPS membranes is observed. After immersing in a hot alkaline solution (80 °C, 1 M KOH) for 30 days, a₅-QAPS exhibits the highest chemical stability. The ion exchange capacity and ionic conductivity of  a₅-QAPS film are reduced by 10.0 and 10.5%, respectively. The weight loss of  a₅-QAPS membrane is 8.0%, which is similar to the value of the pristine backbone. The increased chemical stability can be ascribed to the suitable micromorphology constructed in  a₅-QAPS sample. Besides,  a₅-QAPS membrane shows a high conductivity of 75.5 mS cm^-1, whereas the swelling ratio is limited to 15.0% in liquid water at 80 °C. In addition, a peak power density of 339.1 mW cm^-2 is obtained by applying a₅-QAPS as the APE to the H₂-O₂ fuel cell at 60 °C.

Synthetic approaches for advanced multi-block anion exchange membranes

Despite our ability to post-functionalize poly(arylene ether sulfone) multi-block copolymers by rapid chloromethylation, bromination, or acylation, with degrees of functionalization that exceeded 70% in a few hours, materials formed during attempts to prepare fully post-functionalized multi-block copolymers are poorly soluble due to undesired side reactions, such as crosslinking or di-bromination. In particular, clustered reactive sites in multi-block copolymers increase the chance of self-reactions between polymer backbones, resulting in the formation of by-products. On the other hand, the authentic multi-block copolymer with good solubility and high molecular weight was successfully synthesized using functionalized monomers. Despite its low ion-exchange capacity, the resulting multi-block copolymer outperformed the commercial FAA-3-30 membrane in terms of anion conductivity, even under low relative humidity conditions.

Multi-block copolymers bearing ionic functional groups were synthesized through direct polymerization or post-functionalization.

Structurally Well-Defined Anion-Exchange Membranes Containing Perfluoroalkyl and Ammonium-Functionalized Fluorenyl Groups

Novel anion-conductive polymers containing perfluoroalkyl and ammonium-functionalized fluorene groups were synthesized and characterized. The quaternized polymers synthesized using a dimethylaminated fluorene monomer had a well-defined chemical structure in which each fluorenyl group was substituted with two ammonium groups at specific positions. The resulting polymers had a high molecular weight (M n = 8.9-13.8 kDa, M w = 13.7-24.5 kDa) to provide bendable thin membranes with the ion-exchange capacity (IEC) ranging from 0.7 to 1.9 mequiv g-1 by solution casting. Both transmission electron microscopy images and small-angle X-ray scattering patterns suggested that the polymer membranes possessed a nanoscale phase-separated morphology based on the hydrophilic/hydrophobic differences in the polymer components. Unlike typical anion-exchange membranes found in the literature, hydroxide ion conductivity of the membranes did not increase with increasing IEC because of their high swelling capability in water. The membrane with IEC = 1.2 mequiv g-1 showed balanced properties of high hydroxide ion conductivity (81 mS cm-1 at 80 °C in water) and mechanical strength (>100% elongation and 14 MPa maximum stress at 80 °C, 60% relative humidity). The polymer main chains were stable in 4 M KOH for 1000 h, whereas the trimethylbenzyl-type ammonium groups degraded under the conditions to cause loss in the hydroxide ion conductivity. An H2/O2 fuel cell with the membrane with IEC = 1.2 mequiv g-1 exhibited a maximum power density of 242 mW cm-2 at 580 mA cm-2 current density.

Exploring the Long-Term Hydrolytic Behavior of Zwitterionic Polymethacrylates and Polymethacrylamides

The hydrolytic stability of polymers to be used for coatings in aqueous environments, for example, to confer anti-fouling properties, is crucial. However, long-term exposure studies on such polymers are virtually missing. In this context, we synthesized a set of nine polymers that are typically used for low-fouling coatings, comprising the well-established poly(oligoethylene glycol methylether methacrylate), poly(3-(N-2-methacryloylethyl-N,N-dimethyl) ammoniopropanesulfonate) ("sulfobetaine methacrylate"), and poly(3-(N-3-methacryamidopropyl-N,N-dimethyl)ammoniopropanesulfonate) ("sulfobetaine methacrylamide") as well as a series of hitherto rarely studied polysulfabetaines, which had been suggested to be particularly hydrolysis-stable. Hydrolysis resistance upon extended storage in aqueous solution is followed by ¹H NMR at ambient temperature in various pH regimes. Whereas the monomers suffered slow (in PBS) to very fast hydrolysis (in 1 M NaOH), the polymers, including the polymethacrylates, proved to be highly stable. No degradation of the carboxyl ester or amide was observed after one year in PBS, 1 M HCl, or in sodium carbonate buffer of pH 10. This demonstrates their basic suitability for anti-fouling applications. Poly(sulfobetaine methacrylamide) proved even to be stable for one year in 1 M NaOH without any signs of degradation. The stability is ascribed to a steric shielding effect. The hemisulfate group in the polysulfabetaines, however, was found to be partially labile.