∑3 Twin Boundaries in Gd2Ti2O7 Pyrochlore: Pathways for Oxygen Migration

Microstructure Evolution of Vacuum Diffusion-Bonded 304 Stainless Steel/20 Carbon Steel Bimetallic Interface after Solution Treatment

In this study, a 304 stainless steel (304 SS)/20 carbon steel (20 CS) bimetal was prepared by vacuum diffusion bonding, with 20 CS as the substrate and 304 SS as the cladding layer, and the interfacial microstructure and bonding strength before and after solution treatment were studied. The 304 SS and The 20 CS formed a strong metallurgical bond after being held at 1380 °C for 60 min without defects such as unbonded regions. Diffusion of Cr and Ni atoms from the 304 SS to the 20 CS occurred, and the C atoms diffused from the 20 CS to the 304 SS, forming a carburized region. A pearlitic region with an average width of approximately 20 μm was formed on the 20 CS side. After solution treatment, austenitization was formed in the carburized region, which was accompanied by the formation of twin crystals. The interfacial bonding strength of the bimetal was measured to be 485 MPa, which increased to 547 MPa after the solution treatment.

Structure, thermostability and magnetic properties of cubic Ce2-x Ti2O7 pyrochlore obtained via sol-gel preparation

Lanthanum-based titanates have been attracting considerable interest by virtue of their structural operability and hence diverse physical properties. The preparation of lanthanum-based titanates with novel crystal structure is a fascinating task. In this work, we report the preparation of a cubic Ce_2−xTi₂O₇ pyrochlore using the sol–gel method. The crystal structure, thermostability and magnetism were studied via the temperature dependence of X-ray powder diffraction, X-ray photoelectron spectroscopy and magnetization measurements. It has been revealed that the as-prepared Ce_2−xTi₂O₇ pyrochlore possesses a cubic symmetry (space group: Fd3̄m), however there is an 18(1)% vacancy of Ce ions in the as-prepared samples. No distinct phase transition and thermal expansion anomaly were observed in the investigated temperature range from 300 K to 700 K. Intriguingly, lattice defects may favor the transformation of Ce valence from +3 to +4 and an unusual weak magnetic ordering state emerged up to 400 K. The persistence of magnetism at such high temperatures is rare and mysterious for cerium titanates. Our findings provide the possibility of adjusting the crystal structure and magnetic properties of cerium titanates, anticipated to the development of lanthanum-based oxides.

We report a novel cubic Ce_2−xTi₂O₇ compound prepared via the sol–gel method. There is an 18% vacancy of Ce ions in the as-prepared samples. The lattice defects may favor the transformation of Ce valence from +4 to +3, and a weak magnetic ordering state emerges up to 400 K.

Laser Irradiation-Induced Nanoscale Surface Transformations in Strontium Titanate

We studied the structural transformations and atomic rearrangements in strontium titanate (SrTiO3) via nanosecond pulsed laser irradiation-induced melting and ultrafast quenching. Using scanning transmission electron microscopy, we determine that the laser-irradiated surface in single-crystalline SrTiO3 transforms into an amorphous phase with an interposing disordered crystalline region between amorphous and ordered phases. The formation of disordered phase is attributed to the rapid recrystallization of SrTiO3 from the melt phase constrained by an epitaxial relation with the pristine region, which eases up on the surface, leading to amorphous phase formation. With electron energy-loss spectroscopic analysis, we confirm the transformation of Ti+4 to Ti+3 due to oxygen vacancy formation as a result of laser irradiation. In the disordered region, the maximum transformation of Ti+4 is observed to be 16.2 ± 0.2%, whereas it is observed to be 20.2 ± 0.2% in the amorphous region. Finally, we deduce that the degree of the disorder increases from atomically disordered to amorphous transition in SrTiO3 under laser-irradiation. The signatures of short-range ordering remain similar, leading to a comparable fingerprint of electronic structure. With these results, this study addresses the gap in understanding the atomic and electronic structure modified by pulsed laser irradiation and functionalizing pristine SrTiO3 for electronic, magnetic, and optical applications.

Atomic-Scale Insights on Large-Misfit Heterointerfaces in LSMO/MgO/c-Al2O3

Understanding the interfaces in heterostructures at an atomic scale is crucial in enabling the possibility to manipulate underlying functional properties in correlated materials. This work presents a detailed study on the atomic structures of heterogeneous interfaces in La0.7Sr0.3MnO3 (LSMO) film grown epitaxially on c-Al2O3 (0001) with a buffer layer of MgO. Using aberration-corrected scanning transmission electron microscopy, we detected nucleation of periodic misfit dislocations at the interfaces of the large misfit systems of LSMO/MgO and MgO/c-Al2O3 following the domain matching epitaxy paradigm. It was experimentally observed that the dislocations terminate with 4/5 lattice planes at the LSMO/MgO interface and with 12/13 lattice planes at the MgO/c-Al2O3 interface. This is consistent with theoretical predictions. Using the atomic-resolution image data analysis approach to generate atomic bond length maps, we investigated the atomic displacement in the LSMO/MgO and MgO/c-Al2O3 systems. Minimal presence of residual strain was shown at the respective interface due to strain relaxation following misfit dislocation formation. Further, based on electron energy-loss spectroscopy analysis, we confirmed an interfacial interdiffusion within two monolayers at both LSMO/MgO and MgO/c-Al2O3 interfaces. In essence, misfit dislocation configurations of the LSMO/MgO/c-Al2O3 system have been thoroughly investigated to understand atomic-scale insights on atomic structure and interfacial chemistry in these large misfit systems.

Probing Multiscale Disorder in Pyrochlore and Related Complex Oxides in the Transmission Electron Microscope: A Review

Transmission electron microscopy (TEM), and its counterpart, scanning TEM (STEM), are powerful materials characterization tools capable of probing crystal structure, composition, charge distribution, electronic structure, and bonding down to the atomic scale. Recent (S)TEM instrumentation developments such as electron beam aberration-correction as well as faster and more efficient signal detection systems have given rise to new and more powerful experimental methods, some of which (e.g., 4D-STEM, spectrum-imaging, in situ/operando (S)TEM)) facilitate the capture of high-dimensional datasets that contain spatially-resolved structural, spectroscopic, time- and/or stimulus-dependent information across the sub-angstrom to several micrometer length scale. Thus, through the variety of analysis methods available in the modern (S)TEM and its continual development towards high-dimensional data capture, it is well-suited to the challenge of characterizing isometric mixed-metal oxides such as pyrochlores, fluorites, and other complex oxides that reside on a continuum of chemical and spatial ordering. In this review, we present a suite of imaging and diffraction (S)TEM techniques that are uniquely suited to probe the many types, length-scales, and degrees of disorder in complex oxides, with a focus on disorder common to pyrochlores, fluorites and the expansive library of intermediate structures they may adopt. The application of these techniques to various complex oxides will be reviewed to demonstrate their capabilities and limitations in resolving the continuum of structural and chemical ordering in these systems.