Metal-Organic Framework-Polyacrylonitrile Composite Beads for Xenon Capture

One-pot synthesis of bimetallic Fe-Cu metal-organic frameworks composite for the elimination of organic pollutants via peroxymonosulphate activation

A series of bimetallic of FeCu metal-organic frameworks (MOFs) have been synthesised using a solvothermal process by varying the ratio between the two metals. Further, the bimetallic MOF catalysts were characterised by X-ray powder diffraction, scanning electron microscopy, and infrared spectroscopy techniques. Their catalytic properties for activation of peroxymonosulphate (PMS) have been tested by the removal of a model dye, rhodamine B. As a result, NH2-Fe2.4Cu1-MOF demonstrated the highest degradation, the effect of the ratio NH2-Fe2.4Cu1-MOF/PMS has been studied, and the main reactive species have been assessed. The application of these MOFs in powder form is difficult to handle in successive batch or flow systems. Thus, this study assessed the feasibility of growing NH2-Fe2,4Cu1-MOF on polyacrylonitrile (PAN) spheres using the one-pot solvothermal synthesis method. The optimisation of the catalytic activity of the synthesised composite (NH2-Fe2.4Cu1-MOF@PAN) has been evaluated by response surface methodology using a central composite face-centred experimental design matrix and selecting as independent variables: time, PMS concentration, and catalyst dosage. Based on the results, the optimisation of the operational conditions has been validated. At 2.5 mM PMS, 90 min, and 1.19 g·L-1 of catalyst dosage, maximum degradation (80.92%) has been achieved, which doubles the removal values obtained in previous studies with other MOFs. In addition, under these conditions, the catalyst has been proven to maintain its activity and stability for several cycles without activity loss.

Nanostructured copper-organic frameworks for the generation of sulphate radicals: application in wastewater disinfection

In recent years, the presence of pathogens in the environment has become an issue of widespread concern in society. Thus, new research lines have been developed regarding the removal of pathogens and persistent pollutants in water. In this research, the efficacy of nanostructure copper-organic framework, HKUST-1, has been evaluated for its ability to eliminate Escherichia coli and generate sulphate radicals as catalyst for the treatment of effluents with a high microbiological load via peroxymonosulphate (PMS) activation. The disinfection process has been optimized, achieving complete elimination of Escherichia coli growth after 30 min of testing using a concentration of 60.5 mg/L HKUST-1 and 0.1 mM of PMS. To overcome the operational limitations of this system and facilitate its handling and reutilization in a flow disinfection process, HKUST-1 has been efficiently encapsulated on polyacrylonitrile as a novel development that could be scaled up to achieve continuous treatment.

Metal-Encapsulated, Polymer-Containing Halide Salt Composites as Potential Long-Term Hosts for Radioiodine: Evaluating Halmets, Polyhalmets, and Halcermets

This paper presents composite waste form concepts for radioiodine immobilization including halide-metal (halmet) composites, polymer-halide-metal (polyhalmet) composites, and halide-ceramic-metal (halcermet) composites with data from experiments to evaluate these ideas. The encapsulant metal of choice for the pellets was Bi0, and a cold-press-and-sinter approach was used for creating the pellets. A polymer (i.e., polyacrylonitrile or PAN) phase was included in some composite forms because this porous, passive polymer is used as a host matrix for active chemisorption-based getters. Metals of Ag0, Bi0, and Cu0 were separately embedded into PAN beads, which were loaded with iodine in static tests. Included are details of experiments where PAN removal from the iodine-loaded composite beads was evaluated to reduce the overall volume of the final waste requiring immobilization and to improve the thermal stability of the final composite form. While these experiments demonstrate new concepts for radioiodine immobilization, more work is needed to fully understand the limitations of these approaches and further optimizations are needed before implementation at larger scales is feasible.

Fabrication of Ni−MOF−74@PA−PEI for Radon Removal under Ambient Conditions

Radon is one of the 19 carcinogenic substances identified by the World Health Organization, posing a significant threat to human health and the environment. Properly removing radon under ambient conditions remains challenging. Compared with traditional radon−adsorbent materials such as activated carbon and zeolite, metal–organic framework (MOF) materials provide a high specific surface area, rich structure, and designability. However, MOF material powders demonstrate complications regarding practical use, such as easy accumulation, deactivation, and difficult recovery. Ni−MOF−74 was in situ grown on a porous polyacrylic acid (PA) spherical substrate via stepwise negative pressure impregnation. Ni−MOF−74 was structured as one−dimensional rod−shaped crystals (200–300 nm) in large−pore PA microspheres, whose porous structure increased the diffusion of radon gas. The radon adsorption coefficient of a Ni−MOF−74@PA−polyethyleneimine composite material was 0.49 L/g (293 K, relative humidity of 20%, air carrier). In comparison with pristine Ni−MOF−74 powder, our composite material exhibited enhanced adsorption and longer penetration time. The radon adsorption coefficient of the composite material was found to be from one to two orders of magnitude higher than that of zeolite and silica gel. The proposed material can be used for radon adsorption while overcoming the formation problem of MOF powders. Our preparation approach can provide a reference for the composite process of MOFs and polymers.

MOFs-alginate/polyacrylic acid/poly (ethylene imine) heparin-mimicking beads as a novel hemoadsorbent for bilirubin removal in vitro and vivo models

Metal-organic frameworks (MOFs) have a potential application in blood purification, but their microcrystalline nature has hampered their industrial application. Here, novel MOFs-polymer beads based on UiO, sodium alginate, polyacrylic acid, and poly (ethylene imine) were prepared and applied as a whole blood hemoadsorbent for the first time. The amidation among polymers immobilized UiO66-NH₂ into the network of the optimal product (SAP-3), and the NH₂ of UiO66-NH₂ significantly increased the removal rate (70 % within 5 min) of SAP-3 on bilirubin. The adsorption of SAP-3 on bilirubin mainly obeyed the pseudo-second-order kinetic, Langmuir isotherm and Thomas models with a maximum adsorption capacity (q_m) of 63.97 mg·g^-1. Experimental and density functional theory simulation results show that bilirubin was mainly adsorbed by UiO66-NH₂via electrostatic force, hydrogen bonding, and π-π interactions. Notably, the adsorption in vivo show that the total bilirubin removal rate in the whole blood of the rabbit model was up to 42 % after 1 h of adsorption. Given its excellent stability, cytotoxicity, and hemocompatibility, SAP-3 has a great potential in hemoperfusion therapy. This study proposes an effective strategy for settling the powder property of MOFs and could provide experimental and theoretical references for application of MOFs in blood purification.

Polymeric Fiber Sorbents Embedded with Porous Organic Cages

The synthesis and functionalization of porous organic cages (POCs) for separation have attracted growing interest over the past decade. However, the potential of solid-phase POCs for practical, large-scale separations will require incorporation into appropriate gas-solid or liquid-solid contactors. Contactors with more effective mass transfer properties and lower pressure drops than pelletized systems are preferred. Here, we prepared and characterized fiber sorbents with POCs throughout a cellulose acetate (CA) polymer matrix, which were then deployed in model separations. The POC CC3 was shown to be stable after exposure to spinning solvents, as confirmed by NMR, powder X-ray diffraction, and gas sorption experiments. CC3-CA fibers were spun using the dry-jet wet-quench spinning method. Spun fibers retained the adsorptive properties of CC3 powders, as confirmed by CO₂ and N₂ physisorption and TGA, reaching upward of 60 wt % adsorbent loading, whereas the pelletized CC3 counterparts suffered significant losses in textural properties. The separation capabilities of the CC3-CA fibers are tested with both simulated postcombustion flue gas and with Xe/Kr mixtures. Fixed bed breakthrough experiments performed on fibers samples show that CC3 embedded in polymeric fibers can effectively perform these proof-of-concept gas separations. The development of fiber sorbents embedded with POCs provides an alternative to traditional pelletization for the incorporation of these materials into adsorptive separation systems.