Hollow Au/Polypyrrole Capsules to Form Porous and Neural Network-Like Nanofibrous Film for Wearable, Super-Rapid, and Ultrasensitive NH3 Sensor at Room Temperature

High Sensitivity and Ultra-Broad-Range NH3 Sensor Arrays by Precise Control of Step Defects on The Surface of Cl2-Ndi Single Crystals

Vapor sensors with both high sensitivity and broad detection range are technically challenging yet highly desirable for widespread chemical sensing applications in diverse environments. Generally, an increased surface-to-volume ratio can effectively enhance the sensitivity to low concentrations, but often with the trade-off of a constrained sensing range. Here, an approach is demonstrated for NH3 sensor arrays with an unprecedentedly broad sensing range by introducing controllable steps on the surface of an n-type single crystal. Step edges, serving as adsorption sites with electron-deficient properties, are well-defined, discrete, and electronically active. NH3 molecules selectively adsorb at the step edges and nearly eliminate known trap-like character, which is demonstrated by surface potential imaging. Consequently, the strategy can significantly boost the sensitivity of two-terminal NH3 resistance sensors on thin crystals with a few steps while simultaneously enhancing the tolerance on thick crystals with dense steps. Incorporation of these crystals into parallel sensor arrays results in ppb-to-% level detection range and a convenient linear relation between sheet conductance and semi-log NH3 concentration, allowing for the precise localization of vapor leakage. In general, the results suggest new opportunities for defect engineering of organic semiconductor crystal surfaces for purposeful vapor or chemical sensing.

High-performance pyramid-SiNWs biosensor for NH3gas detection

NH3is widely existed in the environment and is closely associated with various health issues. Additionally, detecting the small amounts of NH3exhaled by patients with liver and kidney diseases offers potential opportunities for painless early disease diagnosis. Therefore, there is an urgent need for a convenient, rapid, and highly sensitive real-time NH3monitoring method. This work presents a high-performance NH3sensor based on olfactory receptor-derived peptides (ORPs) on a pyramid silicon nanowires (SiNWs) structure substrate. First, we successfully fabricated the pyramid-SiNWs structure on a silicon substrate using a chemical etching method. Subsequently, by dehydrative condensation reaction between the amino groups on APTES and the carboxyl groups of ORPs, ORPs were successfully immobilized onto the pyramid-SiNWs structure. This methodology allows the ORPs sensor on the pyramid-SiNWs substrate to detect NH3as low as 1 ppb, which was the reported lowest limit of detection, with a higher response rate compared to ORPs sensors on flat SiNWs substrates. The sensors also exhibit good sensitivity and stability for NH3gas detection. The results show the feasibility and potential applications of ORPs-pyramid-SiNWs structure sensors, in the fields of food safety, disease monitoring, and environmental protection, etc.

Wearable Nano-Based Gas Sensors for Environmental Monitoring and Encountered Challenges in Optimization

With a rising emphasis on public safety and quality of life, there is an urgent need to ensure optimal air quality, both indoors and outdoors. Detecting toxic gaseous compounds plays a pivotal role in shaping our sustainable future. This review aims to elucidate the advancements in smart wearable (nano)sensors for monitoring harmful gaseous pollutants, such as ammonia (NH3), nitric oxide (NO), nitrous oxide (N2O), nitrogen dioxide (NO2), carbon monoxide (CO), carbon dioxide (CO2), hydrogen sulfide (H2S), sulfur dioxide (SO2), ozone (O3), hydrocarbons (CxHy), and hydrogen fluoride (HF). Differentiating this review from its predecessors, we shed light on the challenges faced in enhancing sensor performance and offer a deep dive into the evolution of sensing materials, wearable substrates, electrodes, and types of sensors. Noteworthy materials for robust detection systems encompass 2D nanostructures, carbon nanomaterials, conducting polymers, nanohybrids, and metal oxide semiconductors. A dedicated section dissects the significance of circuit integration, miniaturization, real-time sensing, repeatability, reusability, power efficiency, gas-sensitive material deposition, selectivity, sensitivity, stability, and response/recovery time, pinpointing gaps in the current knowledge and offering avenues for further research. To conclude, we provide insights and suggestions for the prospective trajectory of smart wearable nanosensors in addressing the extant challenges.

An optimization of fungal chitin grafted polyaniline for ammonia gas detection via Box Behnken design

In this work, chitin (Ch) was chemically extracted from wild mushrooms and then grafted to polyaniline (PANI) to form a composite (Ch-g-PANI) to detect ammonia (NH₃) gas. The Ch-g-PANI was comprehensively characterized using Scanning electron microscopy (SEM), elemental mapping, thermogravimetric analysis (TGA), and Fourier transform infrared spectroscopy (FTIR) and UV-Vis spectroscopy. The NH₃ gas detection optimization was evaluated using Box-Behnken Design. Typically, physical factors such as (A)film layer, (B)loading %, and (C)contact time were investigated and validated through the analysis of variance (ANOVA). The ANOVA revealed that dual interactions between (A)film layer - (C)contact time, and (B)loading % - (C)contact time are among the significant factors. By considering these significant interactions, the highest sensitivity was obtained when (A)film layer (3), (B)loading (5 %), and (C)contact time (10 min) in NH₃ gas detection. Then, the optimized Ch-g-PANI was tested in the linear range of NH₃ gas concentration from 10 to 50 ppm, which resulted in a linear calibration curve with R² = 0.994 and a detection limit of 15.03 ppm. Sensor performances showed that Ch-g-PANI films possess high selectivity for NH₃ gas among the common interfering gases and the film can be reused for up to 6 cycles. Therefore, the new mushroom-sourced Ch-g-PANI is an inexpensive and economical sensor in the NH₃ gas sensor field.

Electrospun Conducting Polymers: Approaches and Applications

Inherently conductive polymers (CPs) can generally be switched between two or more stable oxidation states, giving rise to changes in properties including conductivity, color, and volume. The ability to prepare CP nanofibers could lead to applications including water purification, sensors, separations, nerve regeneration, wound healing, wearable electronic devices, and flexible energy storage. Electrospinning is a relatively inexpensive, simple process that is used to produce polymer nanofibers from solution. The nanofibers have many desirable qualities including high surface area per unit mass, high porosity, and low weight. Unfortunately, the low molecular weight and rigid rod nature of most CPs cannot yield enough chain entanglement for electrospinning, instead yielding polymer nanoparticles via an electrospraying process. Common workarounds include co-extruding with an insulating carrier polymer, coaxial electrospinning, and coating insulating electrospun polymer nanofibers with CPs. This review explores the benefits and drawbacks of these methods, as well as the use of these materials in sensing, biomedical, electronic, separation, purification, and energy conversion and storage applications.

Mesoporous cellulose nanofibers-interlaced PEDOT:PSS hybrids for chemiresistive ammonia detection

Chemiresistive ammonia (NH₃) detection at room temperature is highly desired due to the unique merits of easy miniaturization, low cost, and minor energy consumption especially for portable and wearable electronics. In this regard, poly(3,4-ethylenedioxythiophene):polystyrenesulfonate (PEDOT:PSS) has sparked considerable attention due to the benign room-temperature conductivity and environmental stability, but it is undesirably impeded by limited sensitivity and sluggish reaction kinetics. To overcome these, we incorporated cellulose nanofibers (CNF) into PEDOT:PSS via a facile blending. The constituent-optimized composite sensor displayed sensitive (sensitivity of ∼7.46%/ppm in the range of 0.2-3 ppm), selective, and stable NH₃ sensing at 25 °C at 55% RH, with higher response and less baseline drift than pure PEDOT:PSS counterparts. Additionally, the response/recovery times (4.9 s/5.2 s toward 1 ppm NH₃) ranked the best cases of conducting polymers based NH₃ sensors. The humidity involved more than twofold response enhancement indicated a huge potential in exhaled breath monitoring. Furthermore, we observed an excellent flexible NH₃-sensing performance with bending-tolerant features. This work provides an alternative strategy for trace NH₃ sensing with low power consumption, superfast reaction, and high sensitivity.

DFT insights into the selective NH3sensing mechanism of two dimensional ZnTe monolayer

Exploring novel NH₃sensing materials is crucial in chemical industries, fertilizing plants and medical fields. Herein, for the first time, the NH₃sensing behaviors and sensing mechanisms of two dimensional (2D) ZnTe monolayer are systematically investigated by density functional theory calculations. It is shown that 2D ZnTe monolayer exhibits excellent selective NH₃sensing properties. (220) crystal facet of ZnTe possesses a higher NH₃adsorption energy (-1.59 eV) and a larger charge transfer (0.195e) than (111) and (311) crystal facets. The positive charges could enhance NH₃sensing while the negative charges could reduce NH₃sensing. The NH₃adsorption strengths are significantly improved in O₂atmosphere while it is negligibly affected by N₂atmosphere and H₂O atmosphere. Moreover, the presence of Zn vacancy and Fe, Co, Ni doping could improve the NH₃sensing of ZnTe. Additionally, the experimental results confirms that ZnTe possesses a low detection limit of 0.1 ppm NH₃. These theoretical predictions and experimental results present a wide range of possibilities for the further development of ZnTe monolayer in NH₃sensing fields.

Advanced polymeric/inorganic nanohybrids: An integrated platform for gas sensing applications

Rapid industrial development, vehicles, domestic activities and mishandling of garbage are the main sources of pollutants, which are destroying the atmosphere. There is a need to continuously monitor these pollutants for the safety of the environment and human beings. Conventional instruments for monitoring of toxic gases are expensive, bigger in size and time-consuming. Hybrid materials containing organic and inorganic components are considered potential candidates for diverse applications, including gas sensing. Gas sensors convert the information regarding the analyte into signals. Various polymeric/inorganic nanohybrids have been used for the sensing of toxic gases. Composites of different polymeric materials like polyaniline (PANI), poly (4-styrene sulfonate) (PSS), poly (3,4-ethylene dioxythiophene) (PEDOT), etc. with various metal/metal oxide nanoparticles have been reported as sensing materials for gas sensors because of their unique redox features, conductivity and facile operation at room temperature. Polymeric nanohybrids showed better performance because of the larger surface area of nanohybrids and the synergistic effect between polymeric and inorganic materials. This review article focuses on the recent developments of emerging polymeric/inorganic nanohybrids for sensing various toxic gases including ammonia, hydrogen, nitrogen dioxide, carbon oxides and liquefied petroleum gas. Advantages, disadvantages, operating conditions and prospects of hybrid composites have also been discussed.

NiWO4 Microflowers on Multi-Walled Carbon Nanotubes for High-Performance NH3 Detection

NiWO4 microflowers with a large surface area up to 79.77 m2·g-1 are synthesized in situ via a facile coprecipitation method. The NiWO4 microflowers are further decorated with multi-walled carbon nanotubes (MWCNTs) and assembled to form composites for NH3 detection. The as-fabricated composite exhibits an excellent NH3 sensing response/recovery time (53 s/177 s) at a temperature of 460 °C, which is a 10-fold enhancement compared to that of pristine NiWO4. It also demonstrates a low detection limit of 50 ppm; the improved sensing performance is attributed to the porous structure of the material, the large specific surface area, and the p-n heterojunction formed between the MWNTs and NiWO4. The gas sensitivity of the sensor based on daisy-like NiWO4/MWCNTs shows that the sensor based on 10 mol % (MWN10) has the best gas sensitivity, with a sensitivity of 13.07 to 50 ppm NH3 at room temperature and a detection lower limit of 20 ppm. NH3, CO2, NO2, SO2, CO, and CH4 are used as typical target gases to construct the NiWO4/MWCNTs gas-sensitive material and study the research method combining density functional theory calculations and experiments. By calculating the morphology and structure of the gas-sensitive material NiWO4(110), the MWCNT load samples, the vacancy defects, and the influence law and internal mechanism of gas sensitivity were described.