Reactive Janus Particle Compatibilizer with Adjustable Structure and Optimal Interface Location for Compatibilization of Highly Immiscible Polymer Blends

Fluorination Modification of Methyl Vinyl Silicone Rubber and Its Compatibilization Effect on Fluorine/Silicone Rubber Composites

Among numerous rubbers, high-performance rubber composites can be obtained by mixing fluororubber (FKM) with excellent oil resistance and silicone rubber (SiR) with excellent low-temperature resistance. While the difference in polarity between these two kinds of rubbers leads to a reduction in the properties of the composites. To solve the compatibility problem between the two-phase interfaces in FKM/SiR composites, in this research, fluorinated silicone rubbers (MVQ-g-PFDT) of methyl vinyl silicone rubber (MVQ) grafted with 1H,1H,2H,2H-perfluorodecanethiol (PFDT) were prepared via a facile and efficient thiol-ene click reaction, which was then added into FKM/SiR composites. The results showed that the fluorine-containing side chains could effectively inhibit the low-temperature crystallization phenomenon of silicone rubber and further broaden its application ranges in low-temperature environments. The properties of FKM/SiR composites with the addition of MVQ-g-PFDT were significantly improved, with the highest tensile strength of 14.1 MPa and the lowest mass change rate of 6.71% after 48h immersion at 200 °C in IRM903 oil. Additionally, the hydroxyl groups between the fluorine-containing side chains of MVQ-g-PFDT and the surface of silica facilitate the enhancement of the uniform dispersion of fillers. Atomic force microscopy (AFM) characterization results showed a distinct enhancement of the compatibility between the two phases of FKM and SiR. This work would provide further insight into efforts to improve compatibility between rubbers with widely different polarities.

Compatibilization of Immiscible Polypropylene/Poly(methyl methacrylate) Blends by Silica Particles with Janus and Random Component-Selective Grafts

Introducing component-selective polymer chains onto the surface of a particle is an effective approach to improve the compatibilization efficiency of a particle-based compatibilizer. In this study, two particles with different kinds of component-selective polymer chains that have the same length and similar density but different graft locations were synthesized and their compatibilization effects were comparatively investigated. It was found that compared with the particle with homogeneous PMMA and PP grafts (R-P), the particle with a hemisphere of poly(methyl methacrylate) (PMMA) grafts and other hemisphere of polypropylene (PP) chains (J-P) showed a better compatibilization effect under equal loadings, although both particles exhibited high efficiency. The better compatibilization effect of particles with Janus grafts may be attributed to the stronger entanglements between grafted polymer chains and selective individual components. This work suggests that optimizing the graft location of a particle is an effective strategy for improving its compatibilization efficiency and helpful for the design of advanced particle compatibilizers.

In-situ self-crosslinking strategy for super-tough polylactic acid/ bio-based polyurethane blends

As a bio-based degradable plastic, polylactic acid (PLA) is highly commercialized, but its inherent brittleness limits its widespread use. In-situ polymerization techniques are effective in improving the toughness of PLA. However, the enhancement of the toughening effect in polyurethanes (PUs) through in-situ self-crosslinking still requires improvement and heavily relies on petroleum-derived feedstocks in certain approaches. In this paper, 1,3-polypropanediol (PO3G) of bio-based origin rather than conventional polyols like polyethylene glycol (PEG) and poly propylene glycol (PPG) was used. PLA/PO3G-PU blends were prepared via an in-situ self-crosslinking strategy. With a notch impact and tensile strength of 55.95 kJ/m2 and 47.77 MPa (a retention rate of 68.9 % compared with pure PLA), respectively, PLA/PO3G-PU blends achieved a better balance between stiffness and toughness. This work provides a new option for PLA to achieve a stiffness-toughness balance and get rid of dependence on petrochemical resources.

Biodegradable reactive compatibilizers for efficient in-situ compatibilization of poly (lactic acid)/poly (butylene adipate-terephthalate) blends

The wide application of fully biodegradable polylactic acid/polybutylene terephthalate (PLA/PBAT) blends in environmentally friendly packaging were limited because of poor compatibility. Normal compatibilizers suffer from poor thermal stability and non-biodegradability. In this work, epoxy copolymer (MDOG) with different molecular structures were made of 2-methylene-1, 3-dioxoheptane, and glycidyl methacrylate as raw materials by free radical copolymerization. MDOG copolymers have good biodegradability and a high thermal decomposition temperature of 361 °C. The chemical reaction of the epoxy groups in MDOG with PLA and PBAT during the melting reaction improved the interfacial bonding by decreasing the particle size of PBAT. Compared to the PLA/PBAT blends, the tensile strength and fracture toughness of PLA/PBAT/MDOG blends were enhanced to 34.6 MPa and 115.8 MJ/m3, which are 25 % and 81 % higher, respectively. As a result, this work offers new methods for developing thermally stable and biodegradable compatibilizers, which will hopefully promote the development of packaging industry.