Antioxidation Properties and Surface Interactions of Polyvinylpyrrolidone-Capped Zerovalent Copper Nanoparticles Synthesized in Supercritical Water

Encapsulation of Copper Nanoparticles in Electrospun Nanofibers for Sustainable Removal of Pesticides

The excellent catalytic properties of copper nanoparticles (CuNPs) for the degradation of the highly toxic and recalcitrant chlorpyrifos pesticide are widely known. However, CuNPs generally present low stability caused by their high sensitivity to oxidation, which leads to a change of the catalytic response over time. In the current work, the immobilization of CuNPs into a polycaprolactone (PCL) matrix via electrospinning was demonstrated to be a very effective method to retard air and solvent oxidation and to ensure constant catalytic activity in the long term. CuNPs were successfully anchored into PCL electrospun fibers in the form of Cu₂O at different concentrations (from 1.25 wt % to 5 wt % with respect to the PCL), with no signs of loss by leaching out. The PCL mats loaded with 2.5 wt % Cu (PCL-2.5Cu) almost halved the initial concentration of pesticide (40 mg/L) after 96 h. This process was performed in two unprompted and continuous steps that consisted of adsorption, followed by degradation. Interestingly, the degradation process was independent of the light conditions (i.e., not photocatalytic), expanding the application environments (e.g., groundwaters). Moreover, the PCL-2.5Cu composite presents high reusability, retaining the high elimination capability for at least five cycles and eliminating a total of 100 mg/L of chlorpyrifos, without exhibiting any sign of morphological damages.

Band-Gap Engineering of Layered Perovskites by Cu Spacer Insertion as Photocatalysts for Depollution Reaction

A multi-step ion-exchange methodology was developed for the fabrication of Cu(LaTa2O7)2 lamellar architectures capable of wastewater depollution. The (001) diffraction line of RbLaTa2O7 depended on the guest species hosted by the starting material. SEM and TEM images confirmed the well-preserved lamellar structure for all intercalated layered perovskites. The UV–Vis, XPS, and photocurrent spectroscopies proved that Cu intercalation induces a red-shift band gap compared to the perovskite host. Moreover, the UV–Vis spectroscopy elucidated the copper ions environment in the Cu-modified layered perovskites. H2-TPR results confirmed that Cu species located on the surface are reduced at a lower temperature while those from the interlayer occur at higher temperature ranges. The photocatalytic degradation of phenol under simulated solar irradiation was used as a model reaction to assess the performances of the studied catalysts. Increased photocatalytic activity was observed for Cu-modified layered perovskites compared to RbLaTa2O7 pristine. This behavior resulted from the efficient separation of photogenerated charge carriers and light absorption induced by copper spacer insertion.

Investigation of the Characteristics and Antibacterial Activity of Polymer-Modified Copper Oxide Nanoparticles

The proliferation of drug-resistant pathogens continues to increase, giving rise to serious public health concerns. Many researchers have formulated metal oxide nanoparticles for use as novel antibacterial agents. In the present study, copper oxide (CuO) was synthesized by simple hydrothermal synthesis, and doping was performed to introduce different polymers onto the NP surface for bacteriostasis optimization. The polymer-modified CuO NPs were analyzed further with XRD, FTIR, TEM, DLS and zeta potential to study their morphology, size, and the charge of the substrate. The results indicate that polymer-modified CuO NPs had a significantly higher bacteriostatic rate than unmodified CuO NPs. In particular, polydopamine (PDA)-modified CuO (CuO-PDA) NPs, which carry a weakly negative surface charge, exhibited excellent antibacterial effects, with a bacteriostatic rate of up to 85.8 ± 0.2% within 3 h. When compared to other polymer-modified CuO NPs, CuO-PDA NPs exhibited superior bacteriostatic activity due to their smaller size, surface charge, and favorable van der Waals interactions. This may be attributed to the fact that the CuO-PDA NPs had relatively lipophilic structures at pH 7.4, which increased their affinity for the lipopolysaccharide-containing outer membrane of the Gram-negative bacterium Escherichia coli.

Catalytic performance promoted on Pt-based diesel oxidation catalyst assisted by polyvinyl alcohol

Eliminating vehicle emission is of importance due to the severe limit value. The work reports a convenient strategy of improving dispersion of platinum-based catalyst with the assistance of polyvinyl alcohol in a varied addition amount. Following the "two-step" annealing techniques, the catalytic performance of the polymer-assisted catalysts in diesel was obviously enhanced because of the improved dispersion of the platinum. Based on experimental results, the long chains of polymer resulting in the steric effect are presumed to isolate platinum ion, inhibiting the aggregation of platinum particles and then improving its dispersion. And the hydroxyl bonding between the polymers could convey electron to platinum species, leading to the lower platinum valence state. Both effects are positive resulting in an excellent NO maximum conversion of around 65% at the optimal introduction of 5 mass% of polymer, as the diesel oxidation catalyst (DOC), which could be inclined to a good purification in the diesel aftertreatment. Hopefully, the convenient research method could initiate the exploration and application of polymer-assisted catalysts for well-dispersed noble metal nanoparticles in eliminating exhaust emission.

Sub 1 nm Poly(acrylic acid)-Capped Copper Nanoparticles for the Synthesis of 1,2,3-Triazole Compounds

The stable, water-soluble, and fluorescent sub 1 nm sized poly(acrylic acid)-capped copper nanoparticles (PAACC NPs) were synthesized using a high-intensity ultrasound sonication (30 KHz) method. The reduction of copper NPs from copper(II) salt by mild reducing agent l-ascorbic acid in an aqueous medium was achieved in the presence of poly(acrylic acid). The PAACC NPs were characterized by DRS UV-visible, XPS, PL, FESEM, and HRTEM techniques. The resulting PAACC NPs show orange fluorescence with a peaking center at 560 nm. The PAACC NPs serve as effective catalysts for the synthesis of 1,2,3-triazoles via click reaction in good yields under mild reaction conditions.

Inorganic nanoparticle synthesis in flow reactors – applications and future directions

The use of flow technologies for obtaining nanoparticles can play an important role in the development of ecological and sustainable processes for obtaining inorganic nanomaterials, and the continuous methods are part of the Flow Chemistry trend.

Facile and scalable fabrication of self-assembled Cu architecture with superior antioxidative properties and improved sinterability as a conductive ink for flexible electronics

The inherent susceptibility to oxidation and poor sinterability significantly limit the practical application of Cu-based conductive inks. Most methodologies employed for the inks like organic polymer coatings and inorganic metal deposition are generally ineffective. Herein, we report the design of a novel hierarchical Cu architecture to simultaneously improve the antioxidative and sinterability via a self-passivation mechanism and loose interior structures. The hierarchical Cu architecture was prepared using copper hydroxide, L-ascorbic acid, and polyvinylpyrrolidone in aqueous solution; 40 g Cu were prepared in a scale-up experiment. A possible growth mechanism is proposed, involving the Cu₂O-templated and mediated nucleation and growth of Cu nanocrystals, followed by the PVP-directed electrostatic self-assembly of Cu nanocrystals. The synthesized Cu shows high oxidation resistance after stored in ambient environment for 90 d by self-passivation, wherein the dense oxidized external layer prevented further oxidation of Cu, unlike other antioxidative strategies. In addition, the structure became 2D flake after a simple ball-milling for 10 min of 2000r, thus forming a good conductive network at the temperature of 180 °C. Importantly, no obvious decline in the electrical performance after severe surface oxidation. Although the structure cannot offer excellent conductive performance, but it proposes a new solution for the balance of antioxidative capabilities and good sinterability in Cu nanomaterials, thus facilitating greater utilization of Cu-based conductive inks for emerging flexible electronic applications.

The direct-writing of low cost paper based flexible electrodes and touch pad devices using silver nano-ink and ZnO nanoparticles

We report a novel and simple approach for the synthesis of silver nanoparticles capped with inositol (Ag NPs/Ino) by the reduction of silver salt with ascorbic acid under basic conditions. UV-vis, TEM, FTIR and TGA techniques were used to characterize the Ag NPs/Ino to determine the size, shape and surface modification of the NPs. Stable silver nano-ink was prepared in aqueous solution containing 1% PVP (stabilizer) and glycerol (cosolvent) and was used for the direct-writing of a paper electrode with a roller ball-point pen for electrochemical applications. The solvent, stabilizing agents, concentration of NPs (10%), paper substrate, sintering temperature (40 °C) and sintering time (15 min) were optimized to obtain a uniform coating of Ag NPs on the paper substrate. Further, the synthesis and fabrication of ZnO NPs on a paper substrate was put forward to design a touch pad device based on the piezoelectric effect. The preparation of paper based devices suggests a direction for the development of a simple, low cost and compatible approach for the direct-writing of paper based flexible electrodes and electronics for future applications.

Degradable NIR-PTT Nanoagents with a Potential Cu@Cu2O@Polymer Structure

Cu@Cu₂O@PSMA polymer nanoparticles (Cu@Cu₂O@polymer NPs) with near-infrared (NIR) absorption were successfully synthesized in a single-step oxidation reaction of Cu@PSMA polymer NPs at 100 °C for 20 min. The shape, structure, and optical properties of the Cu@Cu₂O@polymer NPs were tailorable by controlling the reaction parameters, for example, using the initial Cu@PSMA polymer NP as a template and varying the halide ion content, heating temperature, and reaction time. The Cu@Cu₂O@polymer NPs exhibited robust NIR absorption between 650 and 710 nm and possessed superior oxidation resistance in water and culture media. In vitro assays demonstrated the low cytotoxicity of the Cu@Cu₂O@PSMA polymer NPs to HeLa cells through an improved cell viability, high IC₅₀, low injury incidence from the supernatant of the partly dissociated Cu@Cu₂O@PSMA polymer NPs, and minor generation of reactive oxygen species. More importantly, we demonstrated that the inorganic Cu-based nanocomposite [+0.34 V vs normal hydrogen electrode (NHE)] was degradable in an endogenous H₂O₂ (+1.78 V vs NHE) environment. Cu ions were detected in the urine of mice, which illustrates the possibility of extraction after the degradation of the Cu-based particles. 'After an treatment of the HeLa cells with the Cu@Cu₂O@polymer NPs and a 660 nm light-emitting diode, the photoablation of 50 and 90% cells was observed at NP doses of 20 and 50 ppm, respectively. These results demonstrate that NIR-functional and moderate redox-active Cu@Cu₂O@polymer NPs are potential next-generation photothermal therapy (PTT) nanoagents because of combined features of degradation resistance in the physiological environment, enabling the delivery of efficient PTT, a possibly improved ability to selectively harm cancer cells by releasing Cu ions under high-H₂O₂ and/or low-pH conditions, and ability to be extracted from the body after biodegradation.

Size and surface effects on chemically-induced joining of Ag conductive inks

The underlying roles of particle size effects and ionic salts are uncovered for optimal chemically-induced sintering as a scalable approach to join metallic nanomaterials to create efficient sensors.

Continuous Hydrothermal Synthesis of Inorganic Nanoparticles: Applications and Future Directions

Nanomaterials are at the leading edge of the emerging field of nanotechnology. Their unique and tunable size-dependent properties (in the range 1-100 nm) make these materials indispensable in many modern technological applications. In this Review, we summarize the state-of-art in the manufacture and applications of inorganic nanoparticles made using continuous hydrothermal flow synthesis (CHFS) processes. First, we introduce ideal requirements of any flow process for nanoceramics production, outline different approaches to CHFS, and introduce the pertinent properties of supercritical water and issues around mixing in flow, to generate nanoparticles. This Review then gives comprehensive coverage of the current application space for CHFS-made nanomaterials including optical, healthcare, electronics (including sensors, information, and communication technologies), catalysis, devices (including energy harvesting/conversion/fuels), and energy storage applications. Thereafter, topics of precursor chemistry and products, as well as materials or structures, are discussed (surface-functionalized hybrids, nanocomposites, nanograined coatings and monoliths, and metal-organic frameworks). Later, this Review focuses on some of the key apparatus innovations in the field, such as in situ flow/rapid heating systems (to investigate kinetics and mechanisms), approaches to high throughput flow syntheses (for nanomaterials discovery), as well as recent developments in scale-up of hydrothermal flow processes. Finally, this Review covers environmental considerations, future directions and capabilities, along with the conclusions and outlook.

Palladium nanoparticles exposure: Evaluation of permeation through damaged and intact human skin

The intensified use of palladium nanoparticles (PdNPs) in many chemical reactions, jewellery, electronic devices, in car catalytic converters and in biomedical applications lead to a significant increase in palladium exposure. Pd can cause allergic contact dermatitis when in contact with the skin. However, there is still a lack of toxicological data related to nano-structured palladium and information on human cutaneous absorption. In fact, PdNPs, can be absorbed through the skin in higher amounts than bulk Pd because NPs can release more ions. In our study, we evaluated the absorption of PdNPs, with a size of 10.7 ± 2.8 nm, using intact and damaged human skin in Franz cells. 0.60 mg cm(-2) of PdNPs were applied on skin surface for 24 h. Pd concentrations in the receiving solutions at the end of experiments were 0.098 ± 0.067 μg cm(-2) and 1.06 ± 0.44 μg cm(-2) in intact skin and damaged skin, respectively. Pd flux permeation after 24 h was 0.005 ± 0.003 μg cm(-2) h(-1) and 0.057 ± 0.030 μg cm(-2) h(-1) and lag time 4.8 ± 1.7 and 4.2 ± 3.6 h, for intact and damaged skin respectively. This study indicates that Pd can penetrate human skin.