Electrochemical Exfoliation of Graphite in Aqueous Sodium Halide Electrolytes toward Low Oxygen Content Graphene for Energy and Environmental Applications

Promoting Li+-Solvents Desolvation by Engineering Nickel Single Atoms into Graphene Membrane toward Fast Sulfur Redox Kinetics

Lithium-sulfur (Li-S) batteries featuring high energy density are expected to be next-generation energy storage devices, but are severely impeded by the suppressive Li+-solvents desolvation process at the electrode/electrolyte interface. Herein, a novel electrochemical in situ doping coupled with a self-assembly strategy is proposed to fabricate the graphene membrane anchored by Ni single atoms (Ni-SA-G), aimed at promoting the dissociation kinetics of Li+-solvents complex by combining electrocatalysis and nanochannel sieving effect. Theoretical simulation and in situ Raman spectroscopy characterizations revealed that the Ni-O5 configuration within the Ni-SA-G membrane is capable of lowering the Li+-solvent dissociation energy barrier and promoting free Li+ migration, thereby delivering the fast sulfur redox kinetics. In addition, taking advantage of the Ni-SA-G membrane with a special transport channel, the large-sized solvent molecules and polysulfides were sieved and confined to a great degree. As a result, the Li-S batteries with the Ni-SA-G on separator as cathode front-faces exhibit a high capacity of 1169 mAh g-1 with a good rate performance and outstanding long-term cycling stability, where a capacity decay of only 0.024 % per cycle after 700 cycles can be achieved. Furthermore, the cell with a sulfur loading of 4.78 mg cm-2 delivers a high areal capacity of 4.0 mAh cm-2 at 0.2 C.

A High-Performance, Low Defected, and Binder-Free Graphene-Based Supercapacitor Obtained via Synergistic Electrochemical Exfoliation and Electrophoretic Deposition Process

An integrated electrochemical exfoliation and electrophoretic deposition (EPD) method is developed to achieve a high-performance graphene supercapacitor. The electrochemical delamination of graphite sheet has obtained a low-defected few-layer graphene adorned with oxygen-containing functional groups. Then, the EPD process produced a binder-free electrode to alleviate the graphene restacking problem. The electrode prepared using a deposition voltage of 5 V exhibits the highest specific capacitance of 145.95 F/g at 0.5 A/g from three-electrode measurement. Moreover, this EPD-prepared electrode also demonstrates superior electrochemical properties compared to electrodes fabricated using PVDF binder. In the real symmetrical cell, the EPD-prepared electrode also shows excellent performance with a high rate capability of 82.31 % (from 0.5 A/g to 10 A/g), high cycling stability of 95.00 % (at 5 A/g) after 10,000 cycles, and rapid frequency response with short relaxation time (τ 0 ${{\tau }_{0}}$ ) of 9.73 ms. These results indicate that this integration method is beneficial to construct a high performance binder-free supercapacitor electrode consisting of low-defected graphene materials, low electrode resistance, and less agglomeration of graphene sheets by utilizing an environmentally friendly process.

Electrochemically Exfoliated Graphene Additive-Free Inks for 3D Printing Customizable Monolithic Integrated Micro-Supercapacitors on a Large Scale

Three-dimensional (3D) printing technology with enhanced fidelity can achieve multiple functionalities and boost electrochemical performance of customizable planar micro-supercapacitors (MSCs), however, precise structural control of additive-free graphene-based macro-assembly electrode for monolithic integrated MSCs (MIMSCs) remains challenging. Here, the large-scale 3D printing fabrication of customizable planar MIMSCs is reported utilizing additive-free, high-quality electrochemically exfoliated graphene inks, which is not required the conventional cryogenic assistance during the printing process and any post-processing reduction. The resulting MSCs reveal an extremely small engineering footprint of 0.025 cm2, exceptionally high areal capacitance of 4900 mF cm-2, volumetric capacitance of 195.6 F cm-3, areal energy density of 2.1 mWh cm-2, and unprecedented volumetric energy density of 23 mWh cm-3 for a single cell, surpassing most previously reported 3D printed MSCs. The 3D printed MIMSC pack is further demonstrated, with the maximum areal cell count density of 16 cell cm-2, the highest output voltage of 192.5 V and the largest output voltage per unit area of 56 V cm-2 up to date are achieved. This work presents an innovative solution for processing high-performance additive-free graphene ink and realizing the large-scale production of 3D printed MIMSCs for planar energy storage.

Graphene in 3D Bioprinting

Three-dimensional (3D) bioprinting is a fast prototyping fabrication approach that allows the development of new implants for tissue restoration. Although various materials have been utilized for this process, they lack mechanical, electrical, chemical, and biological properties. To overcome those limitations, graphene-based materials demonstrate unique mechanical and electrical properties, morphology, and impermeability, making them excellent candidates for 3D bioprinting. This review summarizes the latest developments in graphene-based materials in 3D printing and their application in tissue engineering and regenerative medicine. Over the years, different 3D printing approaches have utilized graphene-based materials, such as graphene, graphene oxide (GO), reduced GO (rGO), and functional GO (fGO). This process involves controlling multiple factors, such as graphene dispersion, viscosity, and post-curing, which impact the properties of the 3D-printed graphene-based constructs. To this end, those materials combined with 3D printing approaches have demonstrated prominent regeneration potential for bone, neural, cardiac, and skin tissues. Overall, graphene in 3D bioprinting may pave the way for new regenerative strategies with translational implications in orthopedics, neurology, and cardiovascular areas.

A bio-inspired approach for the synthesis of few-layer graphene using beetle defensive gland extract

Graphene exhibits remarkable properties and holds substantial promise for diverse applications. Its unique combination of thermal, chemical, physical, and biological properties makes it an appealing material for a wide range of uses. But, the lack of an economical and environmentally friendly approach to synthesize good-quality graphene represents an immense challenge for the scientific community. What makes this research unique is the utilization of the defensive gland extract from the beetle species Luprops tristis (Order: Coleoptera, Family: Tenebrionidae) to synthesize a few layers of graphene (FLG). This innovative incorporation of natural resources and exploration of biologically inspired methods provides an eco-friendly and cost-effective alternative to conventional graphene production techniques. The exfoliated graphene displayed antimicrobial effects against both Gram-positive (Staphylococcus aureus) and Gram-negative (Escherichia coli) bacteria, with particularly potent bactericidal activity. Additionally, the cytotoxicity assay demonstrated the anti-cancer properties of biosynthesized graphene against Daltons Lymphoma Acetic (DLA) cells.

Recent Trends in Graphene-Based Sorbents for LC Analysis of Food and Environmental Water Samples

This review provides an overview of recent advancements in applying graphene-based materials as sorbents for liquid chromatography (LC) analysis. Graphene-based materials are promising for analytical chemistry, including applications as sorbents in liquid chromatography. These sorbents can be functionalized to produce unique extraction or stationary phases. Additionally, graphene-based sorbents can be supported in various materials and have consequently been applied to produce various devices for sample preparation. Graphene-based sorbents are employed in diverse applications, including food and environmental LC analysis. This review summarizes the application of graphene-based materials in food and environmental water analysis in the last five years (2019 to 2023). Offline and online sample preparation methods, such as dispersive solid phase microextraction, stir bar sorptive extraction, pipette tip solid phase extraction, in-tube solid-phase microextraction, and others, are reviewed. The review also summarizes the application of the columns produced with graphene-based materials in separating food and water components and contaminants. Graphene-based materials have been reported as stationary phases for LC columns. Graphene-based stationary phases have been reported in packed, monolithic, and open tubular columns and have been used in LC and capillary electrochromatography modes.

Insights into the Conductive Network of Electrochemical Exfoliation with Graphite Powder as Starting Raw Material for Graphene Production

Electrochemical exfoliation starting with graphite powder as the raw material for graphene production shows superiority in cost effectiveness over the popular bulk graphite. However, the crucial conductive network inside the graphite powder electrode along with its formation and influence mechanisms remains blank. Here, an adjustable-pressure graphite powder electrode with a sandwich structure was designed for this. Appropriate encapsulation pressure is necessary and conducive to constructing a continuous and stable conductive network, but overloaded encapsulation pressure is detrimental to the exfoliation and graphene quality. With an initial encapsulation pressure (IEP) of 4 kPa, the graphite powders expand rapidly to a final stable expansion pressure of 49 kPa with a final graphene yield of 46.3%, where 84% of the graphene sheets are less than 4 layers with I_D/I_G values between 0.22 and 1.24. Increasing the IEP to 52 kPa, the expansion pressure increases to 73 kPa, but the graphene yield decreases to 39.3% with a worse graphene quality including higher layers and I_D/I_G values of 1.68-2.13. In addition, small-size graphite powders are not suitable for the electrochemical exfoliation. With the particle size decreasing from 50 to 325 mesh, the graphene yield decreases almost linearly from 46.3% to 5.5%. Conductive network and electrolyte migration synergize and constrain each other, codetermining the electrochemical exfoliation. Within an encapsulated structure, the electrochemical exfoliation of the graphite powder electrode proceeds from the outside to the inside. The insights revealed here will provide direction for further development of electrochemical exfoliation of graphite powder to produce graphene.

Laser Cutting Coupled with Electro-Exfoliation to Prepare Versatile Planar Graphene Electrodes for Energy Storage

The study of planar energy storage devices, characterized by low-cost, high capacity, and satisfactory flexibility, is becoming a valuable research hotspot. Graphene, monolayer sp2 hybrid carbon atoms with a large surface area, always acts as its active component, yet there is a tension between its high conductivity and ease of implementation. Although the difficult-to-assemble graphene can easily achieve planar assemblies in its highly oxidized form (GO), the undesirable conductivity, even after proper reduction, still restricts its further applications. Here, a facile “Top-down” method has been proposed to prepare the graphene planar electrode via in situ electro-exfoliation of graphite supported on a piece of laser-cutting patterned scotch tape. Detailed characterizations have been performed to study its physiochemical property evolution during electro-exfoliation. The obtained flexible graphene planar electrodes show decent energy storage performance, e.g., 40.8 mF cm−2 at a current density of 0.5 mA cm−2 and an 81% capacity retention at a current density of 8 mA cm−2 for the optimized sample G-240. Their high conductivity also makes it possible to couple them with other redox-active materials through electrodeposition to improve their performance, e.g., ferrocene-functionalized mesoporous silica film (Fc-MS), MnO2, and polyaniline (PANI). The highest capacity was achieved with the PANI functionalized sample, which achieved a 22-fold capacity increase. In a word, the versatility, practicality, and adaptability of the protocol to prepare the planar graphene electrode proposed in this work make it a potential candidate to meet the continuously growing energy storage demands.

Recent advances in carbon-based materials for high-performance perovskite solar cells: gaps, challenges and fulfillment

Presently, carbon-based nanomaterials have shown tremendous potential for energy conversion applications. Especially, carbon-based materials have emerged as excellent candidates for the fabrication of halide perovskite-based solar cells, which may lead to their commercialization. In the last decade, PSCs have rapidly developed, and these hybrid devices demonstrate a comparable performance to silicon-based solar cells in terms of power conversion efficiency (PCE). However, PSCs lag behind silicon-based solar cells due to their poor stability and durability. Generally, noble metals such gold and silver are employed as back electrode materials during the fabrication of PSCs. However, the use of these expensive rare metals is associated with some issues, urgently necessitating the search for cost-effective materials, which can realize the commercial applications of PSCs due to their interesting properties. Thus, the present review shows how carbon-based materials can become the main candidates for the development of highly efficient and stable PSCs. Carbon-based materials such as carbon black, graphite, graphene nanosheets (2D/3D), carbon nanotubes (CNTs), carbon dots, graphene quantum dots (GQDs) and carbon nanosheets show potential for the laboratory and large-scale fabrication of solar cells and modules. Carbon-based PSCs can achieve efficient and long-term stability for both rigid and flexible substrates because of their high conductivity and excellent hydrophobicity, thus showing good results in comparison to metal electrode-based PSCs. Thus, the present review also demonstrates and discusses the latest state-of-the-art and recent advances for carbon-based PSCs. Furthermore, we present perspectives on the cost-effective synthesis of carbon-based materials for the broader view of the future sustainability of carbon-based PSCs.

Preparation of multi-function graphene materials through electrode-distance controlled electrochemical exfoliation

Preparation of graphene materials with different microstructures is of great significance for the specific applications in various areas. Here, a modified electrochemical exfoliation method with controlled electrode distance is proposed to prepare exfoliated graphene, graphene quantum dots, and graphene oxide (EGr, EGQD, and EGO). Compared with electrolysis at a fixed location, the modified electrode distance can effectively tune the insertion speed and direction, as well as the kinetic rates of exfoliation processes. Specifically, at a short electrode distance of 3 cm, it produced high-quality EGr with the size above 5μm and thickness below 5 layers; when the electrode distance increased to 30 cm, EGQD with the size below 5 nm was produced. Further, the distance between 3 and 30 cm facilitates producing EGO with ca. 15% O content. In addition, it is found that the reaction temperature, optimized electrolyte, and controlled potential can further optimize the exfoliation processes, which can achieve a high exfoliation rate of ca. 2000, 140, and 1500 g h^-1for EGr, EGQD, and EGO preparation in an industrial-scale system, respectively. These modified graphene materials can be directly applied in various areas. For example, EGr can act as an effective component to increase one order of the dielectric property of PVDF; EGQD can effectively generate a PL spectrum at ca. 550 nm; EGO can facilely form a conductive and flexible film through self-assembly.

Graphene Synthesis: Method, Exfoliation Mechanism and Large-Scale Production

Graphene is a unique attractive material owing to its characteristic structure and excellent properties. To improve the preparation efficiency of graphene, reduce defects and costs, and meet the growing market demand, it is crucial to explore the improved and innovative production methods and process for graphene. This review summarizes recent advanced graphene synthesis methods including “bottom-up” and “top-down” processes, and their influence on the structure, cost, and preparation efficiency of graphene, as well as its peeling mechanism. The viability and practicality of preparing graphene using polymers peeling flake graphite or graphite filling polymer was discussed. Based on the comparative study, it is potential to mass produce graphene with large size and high quality using the viscoelasticity of polymers and their affinity to the graphite surface.

A Simple and Expeditious Route to Phosphate-Functionalized, Water-Processable Graphene for Capacitive Energy Storage

Phosphate-functionalized carbon-based nanomaterials have attracted significant attention in recent years owing to their outstanding behavior in electrochemical energy-storage devices. In this work, we report a simple approach to obtain phosphate-functionalized graphene (PFG) via anodic exfoliation of graphite at room temperature with a high yield. The graphene nanosheets were obtained via anodic exfoliation of graphite foil using aqueous solutions of H3PO4 or Na3PO4 in the dual role of phosphate sources and electrolytes, and the underlying exfoliation/functionalization mechanisms are proposed. The effect of electrolyte concentration was studied, as low concentrations do not lead to a favorable graphite exfoliation and high concentrations produce fast graphite expansion but poor layer-by-layer delamination. The optimal concentrations are 0.25 M H3PO4 and 0.05 M Na3PO4, which also exhibited the highest phosphorus contents of 2.2 and 1.4 at. %, respectively. Furthermore, when PFG-acid at 0.25 M and PFG-salt at 0.05 M were tested as an electrode material for capacitive energy storage in a three-electrode cell, they achieved a competitive performance of ∼375 F/g (540 F/cm3) and 356 F/g (500 F/cm3), respectively. Finally, devices made up of symmetric electrode cells obtained using PFG-acid at 0.25 M possess energy and power densities up to 17.6 Wh·kg-1 (25.3 Wh·L-1) and 10,200 W/kg; meanwhile, PFG-salt at 0.05 M achieved values of 14.9 Wh·kg-1 (21.3 Wh·L-1) and 9400 W/kg, with 98 and 99% of capacitance retention after 10,000 cycles, respectively. The methodology proposed here also promotes a circular-synthesis process to successfully achieve a more sustainable and greener energy-storage device.

Electrochemical approach toward reduced graphene oxide-based electrodes for environmental applications: A review

Graphene has shown great potential in various application fields due to its excellent carrier transportation, ultra-high specific surface area, good mechanical properties, and light transmittance. However, pure graphene still exhibits some insurmountable defects, such as difficulty in simple and large-scale preparation, and limitations in application. The electrochemical method is a simple, clean, and environmentally friendly method. The rapid and simple preparation of graphene and its derivatives by electrochemical methods has important environmental significance. Moreover, rGO-based nanohybrids can be prepared by convenient and quick electrodeposition or cyclic voltammetry (CV), or to change the morphology and structure of graphene and its derivatives to achieve the purpose of improving material properties. This work mainly summarizes electrochemically related graphene from four aspects: (i) the method of electrochemical exfoliation of graphene; (ii) types of electrodeposition rGO-based nanohybrids; (iii) electrochemical regulation of the structure of rGO-based mixtures; (iv) environmental applications of rGO-based nanohybrids prepared by electrodeposition. This article critically discusses the advantages and disadvantages of electrochemical-related graphene, outlines future challenges, and provides insightful views and references for other researchers.

Preparation of hybrid paper electrode based on hexagonal boron nitride integrated graphene nanocomposite for free-standing flexible supercapacitors

Flexible energy storage devices have received great interest due to the increasing demand for wearable and flexible electronic devices with high-power energy sources. Herein, a novel hybrid flexible hexagonal boron nitride integrated graphene paper (BN/GrP) is fabricated from 2D hexagonal boron nitride (h-BN) nanosheets integrated with graphene sheets dispersion via a simple vacuum filtration method. FE-SEM indicated that layered graphene nanosheets tightly confined with h-BN nanosheets. Further, the Raman spectroscopy confirmed successful integration of BN with graphene. As-prepared BN/GrP free-standing flexible conductive paper showed high electrical conductivity of 5.36 × 104 S m-1 with the sheet resistance of 8.87 Ω sq-1. However, after 1000 continuous bending cycles, the BN/GrP sheet resistance increased just about 8.7% which indicated good flexibility of the paper. Furthermore, as-prepared BN/GrP showed excellent specific capacitance of 321.95 F g-1 at current density of 0.5 A g-1. In addition, the power and energy densities were obtained as 3588.3 W kg-1, and 44.7 W h kg-1, respectively. The stability of the prepared flexible electrode was tested in galvanostatic charge/discharge cycles, where the results showed the 96.3% retention even after 6000 cycles. These results exhibited that the proposed BN/GrP may be useful to prepare flexible energy-storage systems.

In situ exfoliation and modification of graphite foil in supercapacitor devices: a facile strategy to fabricate high-performance supercapacitors

Graphite foils (GFs) are emerging as a new class of electrodes in supercapacitors (SCs) based on their light weight, and high electrical conductivity, although the surface area remains low. A novel method of, in situ electrochemical exfoliation and modification of GF in the assembled SCs, showed high energy density and power density of the SC devices.

Simple fabrication for high performance supercapacitors.

Direct Laser Writing of Transparent Polyimide Film for Supercapacitor

Direct laser writing (DLW) is a convenient approach for fabricating graphene-based flexible electronic devices. In this paper, laser-induced graphene was successfully prepared on a thin and transparent polyimide film through the DLW process. Experiments have demonstrated that interdigital thin film capacitor prepared by the DLW method has a high specific capacitance of 8.11 mF/cm² and volume capacitance density of 3.16 F/cm³ (0.05 mA/cm²) due to the doped fluoride in the laser-induced graphene. The capacitance is about 20 times larger than the super-capacitor based non-transparent polyimide film of the same thickness. Owing to its thin, flexible, higher electrochemical characteristics, the transparent polyimide film is promising for integrating and powering portable and wearable electronics.

Ultrafast Construction of Oxygen-Containing Scaffold over Graphite for Trapping Ni2+ into Single Atom Catalysts

Ultrafast construction of oxygen-containing scaffold over graphite for trapping Ni²⁺ into single atom catalysts (SACs) was developed and presented by a one-step electrochemical activation technique. The present method for Ni SACs starts with graphite foil and is capable of achieving ultrafast preparation (1.5 min) and mass production. The defective oxygen featuring the strong electronegativity enables primarily attracting Ni²⁺ ions and stabilizing Ni atoms via Ni-O₆ coordination instead of conventional metal-C or metal-N. In addition, the oxygen defects for trapping are tunable through altering the applied voltage or electrolyte, further altering the loading of Ni atoms, indicative of enhanced oxygen evolution activity. This simple and ultrafast electrochemical synthesis is promising for the mass and controllable production of oxygen-coordinated Ni SACs, which exhibit good performance for oxygen evolution reaction.

Nitrogen-Doped Graphene via In-situ Alternating Voltage Electrochemical Exfoliation for Supercapacitor Application

Doping heteroatom, an effective way to enhance the electrochemical performances of graphene, has received wide attention, especially related to nitrogen. Alternating voltage electrochemical exfoliation, as a low cost and green electrochemical approach, has been developed to construct in-situ N-doped graphene (N-Gh) material. The N-Gh presents a much higher capacity than that of pure graphene prepared via the same method, which might be attributed to the introduction of nitrogen, which has much more effects and a disordered structure. As-prepared N-Gh exhibits a low O/C ratio that is helpful in maintaining high electrical conductivity. And the effects and disorder structure are also conductive to reduce the overlaps of graphene layers. A symmetric supercapacitor assembled with N-Gh electrodes displays a satisfactory rate behavior and long cycling stability (92.3% retention after 5,000 cycles).

A Review on Nano-/Microstructured Materials Constructed by Electrochemical Technologies for Supercapacitors

The article reviews the recent progress of electrochemical techniques on synthesizing nano-/microstructures as supercapacitor electrodes. With a history of more than a century, electrochemical techniques have evolved from metal plating since their inception to versatile synthesis tools for electrochemically active materials of diverse morphologies, compositions, and functions. The review begins with tutorials on the operating mechanisms of five commonly used electrochemical techniques, including cyclic voltammetry, potentiostatic deposition, galvanostatic deposition, pulse deposition, and electrophoretic deposition, followed by thorough surveys of the nano-/microstructured materials synthesized electrochemically. Specifically, representative synthesis mechanisms and the state-of-the-art electrochemical performances of exfoliated graphene, conducting polymers, metal oxides, metal sulfides, and their composites are surveyed. The article concludes with summaries of the unique merits, potential challenges, and associated opportunities of electrochemical synthesis techniques for electrode materials in supercapacitors.

Emerging 2D Materials Produced via Electrochemistry

2D materials are important building blocks for the upcoming generation of nanostructured electronics and multifunctional devices due to their distinct chemical and physical characteristics. To this end, large-scale production of 2D materials with high purity or with specific functionalities represents a key to advancing fundamental studies as well as industrial applications. Among the state-of-the-art synthetic protocols, electrochemical exfoliation of layered materials is a very promising approach that offers high yield, great efficiency, low cost, simple instrumentation, and excellent up-scalability. Remarkably, playing with electrochemical parameters not only enables tunable material properties but also increases the material diversities from graphene to a wide spectrum of 2D semiconductors. Here, a succinct and critical survey of the recent progress in this research direction is presented, comprising the strategic design, exfoliation principles, underlying mechanisms, processing techniques, and potential applications of 2D materials. At the end of the discussion, the emerging trends, challenges, and opportunities in real practice are also highlighted.

Coordinating capillary infiltration with anodic oxidation: a multi-functional strategy for electrochemical fabrication of graphene

Coordinating the capillarity infiltration with anodic oxidation enables electrochemical fabrication of various graphene materials at different temperatures.

Dispersed graphene materials of biomedical interest and their toxicological consequences

Graphene is one-atom thick nanocarbon displaying a unique honeycomb structure and extensive conjugation. In addition to high surface area to mass ratio, it displays unique optical, thermal, electronic and mechanical properties. Atomic scale tunability of graphene has attracted immense research interest with a prospective utility in electronics, desalination, energy sectors, and beyond. Its intrinsic opto-thermal properties are appealing from the standpoint of multimodal drug delivery, imaging and biosensing applications. Hydrophobic basal plane of sheets can be efficiently loaded with aromatic molecules via non-specific forces. With intense biomedical interest, methods are evolving to produce defect-free and dispersion stable sheets. This review summarizes advancements in synthetic approaches and strategies of stabilizing graphene derivatives in aqueous medium. We have described the interaction of colloidal graphene with cellular and sub-cellular components, and subsequent physiological signaling. Finally, a systematic discussion is provided covering toxicological challenges and possible solutions on utilizing graphene formulations for high-end biomedical applications.

Micro-Nano Carbon Structures with Platelet, Glassy and Tube-Like Morphologies

Carbon source precursors for high-grade, clean, and low-carbon refractories were obtained by in situ exfoliation of flake graphite (FG) and phenol–formaldehyde resin (PF) composites with three-roll milling (TRM) for the fabrication of graphite nanoplatelets. In addition, by using Ni(NO₃)₂·6H₂O as a catalyst in the pyrolysis process, multidimensional carbon nanostructures were obtained with coexisting graphite nanoplatelets (GNPs), glassy carbon (GC), and carbon nanotubes (CNTs). The resulting GNPs (exfoliated 16 times) had sizes of 10–30 μm, thicknesses of 30–50 nm, and could be uniformly dispersed in GC from the PF pyrolysis. Moreover, Ni(NO₃)₂·6H₂O played a key role in the formation and growth of CNTs from a catalytic pyrolysis of partial PF with the V–S/tip growth mechanisms. The resulting multidimensional carbon nanostructures with GNPs/GC/CNTs are attributed to the shear force of the TRM process, pyrolysis, and catalytic action of nitrates. This method reduced the production costs of carbon source precursors for low-carbon refractories, and the precursors exhibited excellent performances when fabricated on large scales.

2D/2D Heterojunctions for Catalysis

2D layered materials with atomic thickness have attracted extensive research interest due to their unique physicochemical and electronic properties, which are usually very different from those of their bulk counterparts. Heterojunctions or heterostructures based on ultrathin 2D materials have attracted increasing attention due to the integrated merits of 2D ultrathin components and the heterojunction effect on the separation and transfer of charges, resulting in important potential values for catalytic applications. Furthermore, 2D/2D heterostructures with face-to-face contact are believed to be a preferable dimensionality design due to their large interface area, which would contribute to enhanced heterojunction effect. Here, the cutting-edge research progress in 2D/2D heterojunctions and heterostructures is highlighted with a specific emphasis on synthetic strategies, reaction mechanism, and applications in catalysis (photocatalysis, electrocatalysis, and organic synthesis). Finally, the key issues and development perspectives in the applications of 2D/2D layered heterojunctions and heterostructures in catalysis are also discussed.

Programmed electrochemical exfoliation of graphite to high quality graphene

We propose programed potential modulation strategies to balance the ion intercalation/deintercalation, surface tailoring and bubbling dispersion processes in the electrochemical exfoliation of graphite, resulting in high-quality graphene with high crystallinity, low oxidation degree, uniform size distribution and few layers.

Green and facile synthesis of few-layer graphene via liquid exfoliation process for Lithium-ion batteries

A green and facile method using jet cavitation (JC) was utilized to prepare few layer graphene (FLG) derived from artificial graphite delamination without adding any strong acids and oxidants. The JC method not only provides high quality FLG with high yield but also demonstrate excellent electrochemical performance as anode materials for Li-ion batteries. Raman spectroscopy, scanning electron microscopy (SEM), and transmission electron microscopy (TEM) as well as BET isotherms and XPS are carried out in this study. The results of atomic force microscopy (AFM) further revealed that up to 85% of the prepared FLG were less than 10 layers. This exfoliation process happened mainly due to the cavitation-induced intensive tensile stress acting on the layered materials. Electrochemical measurements demonstrate that graphite anode delivered only 240 mAh/g while FLG anode achieved more than 322 mAh/g at 5C rate test. These results indicate that JC method not only paves the way for cheaper and safer production of graphene but also holds great potential applications in energy-related technology.

Robust and Antibacterial Polymer/Mechanically Exfoliated Graphene Nanocomposite Fibers for Biomedical Applications

With the increasing demand for composites of multifunctional and integrated performance, graphene-based nanocomposites have been attracting increasing attention in biomedical applications because of their outstanding physicochemical properties and biocompatibility. High product yields and dispersion of graphene in the preparation process of graphene-based nanocomposites have long been a challenge. Further, the mechanical properties and biosafety of final nanocomposites are very important for real usage in biomedical applications. Here, we presented a novel high-throughput method of graphene on mechanical exfoliation in a natural honey medium, and a yield of ∼91% of graphene nanoflakes can be easily achieved with 97.76% of single-layer graphenes. The mechanically exfoliated graphene (MEG) can be well-dispersed in the poly(vinyl alcohol) (PVA) matrix. The PVA/MEG nanocomposite fibers are obtained by gel spinning and stretched 20 times. As a candidate for monofilament sutures, the PVA/MEG nanocomposite fibers with 0.3 wt % of MEG have an ultrahigh ultimate tensile strength of 2.1 GPa, which is far higher than that of the neat PVA fiber (0.75 GPa). In addition, the PVA/MEG nanocomposite fibers also have antibacterial property, low cytotoxicity, and other properties. On the basis of the above-mentioned properties, the effects of a common surgical suture and PVA/MEG nanocomposite fibers on wound healing are evaluated. As a result, the wounds treated with PVA/MEG nanocomposite fibers with 0.3 wt % of MEG show the best healing after 5 days of surgery. It is possible that this novel surgical suture will be available in the market relying on the gentle, inexpensive method of obtaining nonoxidized graphene and the simple process of obtaining nanocomposite fibers.