ZnO Nanorod Array Modified PVDF Membrane with Superhydrophobic Surface for Vacuum Membrane Distillation Application

Fouling-Resistant Behavior of Hydrophobic Surfaces Based on Poly(dimethylsiloxane) Modified by Green rGO@ZnO Nanocomposites

In line with global goals to solve marine biofouling challenges, this study proposes an approach to developing a green synthesis inspired by natural resources for fouling-resistant behavior. A hybrid antifouling/foul release (HAF) coating based on poly(dimethylsiloxane) containing a green synthesized nanocomposite was developed as an environmentally friendly strategy. The nanocomposites based on graphene oxide (GO) and using marine sources, leaves, and stems of mangroves (Avicennia marina), brown algae (Polycladia myrica), and zinc oxide were compared. The effectiveness of this strategy was checked first in the laboratory and then in natural seawater. The performance stability of the coatings after immersion in natural seawater was also evaluated. With the lowest antifouling (17.95 ± 0.7%) and the highest defouling (51.2 ± 0.9%), the best fouling-resistant performance was for the coatings containing graphene oxide reduced with A. marina stem/zinc oxide (PrGZS) and graphene oxide reduced with A. marina leaves/zinc oxide with 50% multiwall carbon nanotubes (PrGZHC50), respectively. Therefore, the HAF coatings can be considered as developed and eco-friendly HAF coatings for the maritime industry.

Development of multifunctional membranes via plasma-assisted nonsolvent induced phase separation

Demands on superhydrophobic, self-cleaning and piezoelectric membranes have gained significantly due to their potential to overcome global shortages in clean water and energy. In this study, we have discovered a novel plasma-assisted nonsolvent induced phase separation (PANIPS) method to prepare superhydrophobic, self-cleaning and piezoelectric poly(vinylidene difluoride) (PVDF) membranes without additional chemical modifications or post-treatments. The PANIPS membranes exhibit water contact angles ranging from 151.2° to 166.4° and sliding angles between 6.7° and 29.7°. They also show a high piezoelectric coefficient (d33) of 10.5 pC N-1 and can generate a high output voltage of 10 Vpp. The PANIPS membranes can effectively recover pure water from various waste solutions containing Rose Bengal dye, humic acid, or sodium dodecyl sulfate via direct contact membrane distillation (DCMD). This study may provide valuable insights to fabricate PANIPS membranes and open up new avenues to molecularly design advanced superhydrophobic, self-cleaning, and piezoelectric membranes in the fields of clean water production, motion sensor, and piezoelectric nanogenerator.

Enhanced Anti-Wetting Methods of Hydrophobic Membrane for Membrane Distillation

Increasing issues of hydrophobic membrane wetting occur in the membrane distillation (MD) process, stimulating the research on enhanced anti-wetting methods for membrane materials. In recent years, surface structural construction (i.e., constructing reentrant-like structures), surface chemical modification (i.e., coating organofluorides), and their combination have significantly improved the anti-wetting properties of the hydrophobic membranes. Besides, these methods change the MD performance (i.e., increased/decreased vapor flux and increased salt rejection). This review first introduces the characterization parameters of wettability and the fundamental principles of membrane surface wetting. Then it summarizes the enhanced anti-wetting methods, the related principles, and most importantly, the anti-wetting properties of the resultant membranes. Next, the MD performance of hydrophobic membranes prepared by different enhanced anti-wetting methods is discussed in desalinating different feeds. Finally, facile and reproducible strategies are aspired for the robust MD membrane in the future.

Fluoropolymer Membranes for Membrane Distillation and Membrane Crystallization

Fluoropolymer membranes are applied in membrane operations such as membrane distillation and membrane crystallization where hydrophobic porous membranes act as a physical barrier separating two phases. Due to their hydrophobic nature, only gaseous molecules are allowed to pass through the membrane and are collected on the permeate side, while the aqueous solution cannot penetrate. However, these two processes suffer problems such as membrane wetting, fouling or scaling. Membrane wetting is a common and undesired phenomenon, which is caused by the loss of hydrophobicity of the porous membrane employed. This greatly affects the mass transfer efficiency and separation efficiency. Simultaneously, membrane fouling occurs, along with membrane wetting and scaling, which greatly reduces the lifespan of the membranes. Therefore, strategies to improve the hydrophobicity of membranes have been widely investigated by researchers. In this direction, hydrophobic fluoropolymer membrane materials are employed more and more for membrane distillation and membrane crystallization thanks to their high chemical and thermal resistance. This paper summarizes different preparation methods of these fluoropolymer membrane, such as non-solvent-induced phase separation (NIPS), thermally-induced phase separation (TIPS), vapor-induced phase separation (VIPS), etc. Hydrophobic modification methods, including surface coating, surface grafting and blending, etc., are also introduced. Moreover, the research advances on the application of less toxic solvents for preparing these membranes are herein reviewed. This review aims to provide guidance to researchers for their future membrane development in membrane distillation and membrane crystallization, using fluoropolymer materials.

One-Step Preparation of PVDF/GO Electrospun Nanofibrous Membrane for High-Efficient Adsorption of Cr(VI)

Mass loading of functional particles on the surface of nanofibers is the key to efficient heavy metal treatment. However, it is still difficult to prepare nanofibers with a large number of functional particle loads on the surface simply and efficiently, which hinders the further improvement of performance and increases the cost. Here, a new one-step strategy was developed to maximize the adhesion of graphene oxide (GO) particle to the surface of polyvinylidene fluoride (PVDF) nanofibers, which was combined with coaxial surface modification technology and blended electrospinning. The oxygen content on the as-prepared fiber surface increased from 0.44% to 9.32%, showing the maximized GO load. The increased adsorption sites and improved hydrophilicity greatly promoted the adsorption effect of Cr(VI). The adsorption capacity for Cr(VI) was 271 mg/g, and 99% removal rate could be achieved within 2 h for 20 mL Cr(VI) (100 mg/L), which was highly efficient. After five adsorption-desorption tests, the adsorption removal efficiency of the Cr(VI) maintained more than 80%, exhibiting excellent recycling performance. This simple method achieved maximum loading of functional particles on the fiber surface, realizing the efficient adsorption of heavy metal ions, which may promote the development of heavy-metal-polluted water treatment.

Fabrication of ZnO/y-FeOOH nanoparticles embedded on the polyethylene terephthalate membrane: Evaluation of antifouling behavior and COD removal

Nanofiltration contributes to the development of advanced treatment of wastewater. An antifouling mixed matrix recycled polyethylene terephthalate (rPET) membrane modified by the hydrophilic ZnO/y-FeOOH nanoparticles (NPs) was fabricated via the electrospinning method. The effect of ZnO/y-FeOOH NP_S embedded in rPET as a modifier on the fabrication of nanocomposite membranes was investigated regarding water flux, membrane morphology, permeability, fouling resistance, and COD removal. The surface morphology of the rPET-ZnO/y-FeOOH membrane was evaluated by field emission scanning electron microscopy (FESEM), energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), water contact angle (WCA), and porosity and pore structure.Due to the embedding of NPs, the resulting rPET-ZnO/y-FeOOH membrane, with a low WCA of 53.404° angle, conforms significantly improved hydrophilicity and water permeation flux. The FESEM image displayed the distribution of cuboidal and needle-like ZnO and FeOOH NPs on the rPET membrane. The performance of the nanofiltration system related to the removal efficiency of COD was studied. It was deduced that the rPET-ZnO/y-FeOOH membrane had a superior COD removal capability (95.7%) at a pressure of 2 bar. Protein rejection tests were performed on antifouling behavior. The nanocomposite membrane with a high antifouling capability was related to 0.5 wt·% ZnO/y-FeOOH NPs (flux recovery ratio [FRR] = 96.2%, R_r = 90.21%, and R_ir = 3.001%). The modification procedure in this study (as a great improving technique) was proposed to fabricate the antifouling nanofiltration membrane.

Plasmonic enhanced piezoelectric photoresponse with flexible PVDF@Ag-ZnO/Au composite nanofiber membranes

The coordination of piezoelectric and plasmonic effects to regulate the separation and migration of photo-generated carriers is still a significant method to improve the performance of visible-light photoresponse. Herein, we propose the PVDF@Ag-ZnO/Au composite nanofiber membranes utilizing the piezoelectric and plasmonic effects to promote the photocatalytic degradation of organic dyes. Here, ZnO nanorods can generate a built-in electric field under vibration to separate electron-hole pairs. The Schottky junction formed by noble metal/semiconductor can not only inhibit the recombination of photo-generated carriers and accelerate the migration of carriers, but also enhance the utilization of visible light. In addition, the structure has excellent flexibility and easy recycling characteristics. We demonstrate that the plasmonic effect of noble metal can enhance the light response of membranes and broaden light absorption from ultraviolet to visible light region. With the help of the surface-enhanced Raman scattering (SERS), modulation effects of the piezoelectric effect on light response is proved. For catalytic processes, rhodamine B (98.8%) can be almost completely degraded using PVDF@Ag-ZnO/Au within 120 minutes in the piezoelectric photocatalysis process, which is 2.2 and 2.8 times higher than photocatalysis and piezoelectric catalysis, respectively. This work provides a promising strategy for harnessing solar and mechanical energy.

The advent of thermoplasmonic membrane distillation

Freshwater scarcity is a vital societal challenge related to climate change, population pressure, and agricultural and industrial demands. Therefore, sustainable desalination/purification of salty/contaminated water for human uses is particularly relevant. Membrane distillation is an emerging hybrid thermal-membrane technology with the potential to overcome the drawbacks of conventional desalination by a synergic exploitation of the water-energy nexus. Although membrane distillation is considered a green technology, efficient heat management remains a critical concern affecting the cost of the process and hindering its viability at large scale. A multidisciplinary approach that involves materials chemistry, physical chemistry, chemical engineering, and materials and polymer science is required to solve this problem. The combination of solar energy with membrane distillation is considered a potentially feasible low-cost approach for providing high-quality freshwater with a low carbon footprint. In particular, recent discoveries about efficient light-to-heat conversion in nanomaterials have opened unprecedented perspectives for the implementation of sunlight-based renewable energy in membrane distillation. The integration of nanofillers enabling photothermal effects into membranes has been demonstrated to be able to significantly enhance the energy efficiency without impacting on economic costs. Here, we provide a comprehensive overview on the state of the art, the opportunities, open challenges and pitfalls of the emerging field of solar-driven membrane distillation. We also assess the peculiar physicochemical properties and synthesis scalability of photothermal materials, as well as the strategies for their integration into polymeric nanocomposite membranes enabling efficient light-to-heat conversion and freshwater.

Graphene-Coated PVDF Membranes: Effects of Multi-Scale Rough Structure on Membrane Distillation Performance

Graphene-coated membranes for membrane distillation have been fabricated by using a wet-filtration approach. Graphene nanoplatelets have been deposited onto PVDF membrane surfaces. Morphology and physicochemical properties have been explored to evaluate the changes in the surface topography and related effects on the membrane performance in water desalination. The membranes have been tested in membrane distillation plants by using mixtures of sodium chloride and humic acid. The multi-scale rough structure of the surface has been envisaged to amplify the wetting and fouling resistance of the graphene-coated membranes so that a better flux and full salt rejection have been achieved in comparison with pristine PVDF. Total salt rejection and an increase of 77% in flux have been observed for coated membrane with optimized graphene content when worked with NaCl 0.6 M (DCMD, ΔT ≈ 24 °C) over a test period of 6 h. The experimental findings suggest these novel graphene-coated membranes as promising materials to develop functional membranes for high-performing water desalination.

Evolution of and Disparity among Biomimetic Superhydrophobic Surfaces with Gecko, Petal, and Lotus Effect

It is desirable to turn one kind of superhydrophobic (SHPO) surfaces into another by changing surface topography alone and attaining solid surfaces with tunable properties. Herein, gecko-, petal-, and lotus-like SHPO surfaces, composed of ZnO tetrapods and polydimethylsiloxane, are realized by adjusting the roughness factor and length scale of roughness, while keeping the surface chemistry the same. Afterward, water droplet sliding and impacting are investigated. The surfaces behave similarly in spreading but deviate from each other in sliding, receding, jetting, and rebounding due to their different adhesive properties. Moreover, the disparity between surfaces with petal and lotus effects is well explained by Furmidge's and Young-Dupre equations. On the other hand, these formulas fail to elucidate the surface with gecko effect because of its inside sealed air that produces negative pressure upon droplet motion. This paper provides a facile topography evolution path and a manifest correlation between topography and performance in water droplet dynamics for SHPO surfaces with gecko, petal, and lotus effects.

Recent advancement in Bi5O7I-based nanocomposites for high performance photocatalysts

Bi₅O₇I belongs to the family of bismuth oxyhalides (BiOX, X = Cl, Br, I), having a unique layered structure with an internal electrostatic field that promotes the separation and transfer of photo-generated charge carriers. Interestingly, Bi₅O₇I exhibits higher thermal stability compared to its other BiOX member compounds and absorption spectrum extended to the visible region. Bi₅O₇I has demonstrated applications in diverse fields such as photocatalytic degradation of various organic pollutants, marine antifouling, etc. Unfortunately, owing to its wide band gap of ∼2.9 eV, its absorption lies mainly in the ultraviolet region, and a tiny portion of absorption lies in the visible region. Due to limited absorption, the photocatalytic performance of pure Bi₅O₇I is still facing challenges. In order to reduce the band gap and increase the light absorption capability of Bi₅O₇I, doping and formation of heterostructure strategies have been employed, which showed promising results in the photocatalytic performance. In addition, the plasmonic heterostructures of Bi₅O₇I were also developed to further boost the efficiency of Bi₅O₇I as a photocatalyst. Here, in this review article, we present such recent efforts made for the advanced development of Bi₅O₇I regarding its synthesis, properties and applications. The strategies for photocatalytic performance enhancement have been discussed in detail. Moreover, in the conclusion section, we have presented the current challenges and discussed possible prospective developments in this field.

Membrane Distillation: Recent Configurations, Membrane Surface Engineering, and Applications

Membrane distillation (MD) is a developing membrane separation technology for water treatment that involves a vapor transport driven by the vapor pressure gradient across the hydrophobic membrane. MD has gained wide attention in the last decade for various separation applications, including the separation of salts, toxic heavy metals, oil, and organic compounds from aqueous solutions. Compared with other conventional separation technologies such as reverse osmosis, nanofiltration, or thermal distillation, MD is very attractive due to mild operating conditions such as low temperature and atmospheric pressure, and 100% theoretical salt rejection. In this review, membrane distillation’s principles, recent MD configurations with their advantages and limitations, membrane materials, fabrication of membranes, and their surface engineering for enhanced hydrophobicity are reviewed. Moreover, different types of membrane fouling and their control methods are discussed. The various applications of standalone MD and hybrid MD configurations reported in the literature are detailed. Furthermore, studies on the MD-based pilot plants installed around the world are covered. The review also highlights challenges in MD performance and future directions.

Multifunctional Switchable Nanocoated Membranes for Efficient Integrated Purification of Oil/Water Emulsions

Surfaces with unusual under-liquid dual superlyophobicity are attractive on account of their widespread applications, but their development remains difficult due to thermodynamic contradiction. Additionally, these surfaces may suffer from limited antifouling ability, which has restricted their practical applications. Herein, we report a successful in situ growth of a hybrid zeolitic imidazolate framework-8 and zinc oxide nanorod on a porous poly(vinylidene fluoride) membrane (ZIF-8@ZnO-PPVDF) and its application as a self-cleaning switchable barrier material in rapid filtration for emulsified oily wastewater. The novel ZIF-8@ZnO-PPVDF exhibits superior mechanical strength, reversible under-liquid dual superlyophobicity, photocatalytic self-cleaning property, and an effective alternate separation capacity toward both oil-in-water (O/W) and water-in-oil (W/O) emulsions with ultrahigh fluxes and efficiencies (>99%). By simply using a "bait-hook-eliminate" method to separate the O/W emulsions containing soluble organic pollutants, we demonstrate that the ZIF-8@ZnO-PPVDF can achieve stable separation fluxes over 600 L m^-2 h^-1 with high efficiencies and be completely/nondestructively regenerated by visible-light irradiation after each cycle. This study would demonstrate a new approach to prepare an under-liquid dual superlyophobic revivable membrane for various applications.

Metal oxide and carbon nanomaterial based membranes for reverse osmosis and membrane distillation: A comparative review

Commercial membranes typically suffer from fouling and wetting during membrane distillation (MD). In contrast, reverse osmosis (RO) can be subject to the fouling issue if applied for highly saline feed solutions containing foulants (e.g., organics, oils, and surfactants). Among the diverse treatment options, the nanomaterial-based membranes have recently gained great interest due to their advantageous properties (e.g., enhanced flux and roughness, better pore size distribution, and higher conductivity). This review focuses on recent advances in the mechanical properties, anti-fouling capabilities, salt rejection, and economic viability of metal oxide (SiO₂, TiO₂, and ZnO) and carbon nanomaterial (graphene oxide/carbon nanotube)-based membranes. Current challenges in applying nanomaterial-based membranes are also discussed. The study further describes the preparation methods, mechanisms, commercial applications, and economical feasibility of metal oxide- and carbon nanomaterial-based membrane technologies.

Multifunctional superhydrophobic adsorbents by mixed-dimensional particles assembly for polymorphic and highly efficient oil-water separation

Supra-wetting materials, especially superhydrophobic absorption materials, as an emerging advanced oil-water separation material have attracted extensive concern in the treatment of oil spillage and industrial oily wastewater. However, it is still a challenge to fabricate robust and multifunctional superhydrophobic materials for the multitasking oil-water separation and fast clean-up of the viscous crude oil by an environment-friendly and scalable method. Herein, a solid-solid phase ball-milling strategy without chemical reagent-free modification was proposed to construct heterogeneous superhydrophobic composites by using waste soot as the solid-phase superhydrophobic modifier. A series of covalent bond restricted soot-graphene (S-GN) or soot-Fe₃O₄ (S-Fe₃O₄) composite materials with a peculiar micro-nano structure are prepared. Through "glue+superhydrophobic particles" method, the prepared soot-based composite particles are facilely loaded on the porous skeleton of the sponge to obtain multifunctional superhydrophobic adsorbents. The reported superhydrophobic adsorbents exhibited robust chemical and mechanical stability, convenient magnetic collection, the high oil absorption capacity of 60-142 g g^-1, durable recyclability (>250 cycles), efficient separation efficiency (>99.5%) and outstanding self-heated performance, which enable them to be competent for oil-water separation in multitasking and complex environment (floating oils, continuous oil collection, oil-in-water emulsion, and viscous oil-spills).

Numerical Calculation of Apparent Contact Angles on the Hierarchical Surface with Array Microstructures by Wire Electrical Discharge Machining

It is necessary to theoretically research wettability in superhydrophobic surface fabrication. Here, a numerical calculation approach is proposed for determining the contact angle of the water droplets on array micropillars by wire electrical discharge machining (WEDM). A hierarchical model is employed for these array microstructures, including mechanical analysis for a water droplet placed on a smooth array and wettability evaluation on the morphology of the WEDM surface. On pillars, equations are listed to solve the apparent contact angle according to force balance of gravity, tension, and pressure. As for the WEDM morphology, temperature simulation and measurement are carried out, and then the effect of roughness on surface wettability is studied. Constructed formulas predict the contact angle, and then the effect of geometric dimensions is obtained. In order to verify the assumption, array micropillars with different cross-profiles are prepared using high-speed WEDM on the Al alloy surface. Through the results of contact angle determination, the numerical calculation is carried out. This theoretical prediction is beneficial for improving the fabrication of the superhydrophobic surface by WEDM.

Investigation of the Effects of Component Ratios on the Properties of Superhydrophobic Polyurethane/Fluorinated Acrylic Co-Polymer/SiO2 Nanocomposite Coatings

In this work, polyurethane/fluorinated acrylic co-polymer/silicon dioxide (PU/FAP/SiO2) hybrid superhydrophobic coatings were fabricated on glass substrates via a simple one-step coating process. The effects of each coating component on the coating properties were systematically investigated. The optimized coating exhibits a water contact angle (WCA) of 159° and a rolling angle of 3°. Meanwhile, the coating has an optical light transmittance of 88%, indicating the good transparency of the coating. Besides, the coating demonstrates an adequate level of abrasion resistance. After a total abrasion distance of 300 cm against a piece of 800 mesh sand paper, the sample still kept a water contact angle of about 110°, showing its high abrasion resistance. Therefore, the optimized coating has a great potential for practical application.

A Critical Review of Membrane Wettability in Membrane Distillation from the Perspective of Interfacial Interactions

Hydrophobic membranes used in membrane distillation (MD) systems are often subject to wetting during long-term operation. Thus, it is of great importance to fully understand factors that influence the wettability of hydrophobic membranes and their impact on the overall separation efficiency that can be achieved in MD systems. This Critical Review summarizes both fundamental and applied aspects of membrane wetting with particular emphasis on interfacial interaction between the membrane and solutes in the feed solution. First, the theoretical background of surface wetting, including the relationship between wettability and interfacial interaction, definition and measurement of contact angle, surface tension, surface free energy, adhesion force, and liquid entry pressure, is described. Second, the nature of wettability, membrane wetting mechanisms, influence of membrane properties, feed characteristics and operating conditions on membrane wetting, and evolution of membrane wetting are reviewed in the context of an MD process. Third, specific membrane features that increase resistance to wetting (e.g., superhydrophobic, omniphobic, and Janus membranes) are discussed briefly followed by the comparison of various cleaning approaches to restore membrane hydrophobicity. Finally, challenges with the prevention of membrane wetting are summarized, and future work is proposed to improve the use of MD technology in a variety of applications.

Fabrication and Potential Applications of Highly Durable Superhydrophobic Polyethylene Terephthalate Fabrics Produced by In-Situ Zinc Oxide (ZnO) Nanowires Deposition and Polydimethylsiloxane (PDMS) Packaging

Considerable attention has been devoted to the in-situ deposition of zinc oxide (ZnO) nanowires (ZnO-NWs) on the surface of organic supports, due to their very wide applications in superhydrophobicity, UV shielding, and nanogenerators. However, the poor interfacial bond strength between ZnO-NWs and its support limits their applications. Herein, we developed a facile process to grow robust ZnO-NWs on a polyethylene terephthalate (PET) fabric surface through simultaneous radiation-induced graft polymerization, hydrothermal processing, and in-situ nano-packaging; the obtained materials were denoted as PDMS@ZnO-NWs@PET. The introduction of an adhesion and stress relief layer greatly improved the attachment of the ZnO-NWs to the support, especially when the material was subjected to extreme environment conditions of external friction forces, strong acidic or alkaline solutions, UV-irradiation and even washing with detergent for a long time. The PDMS@ZnO-NWs@PET material exhibited excellent UV resistance, superhydrophobicity, and durability. The ZnO-NWs retained on the fabric surface even after 30 cycles of accelerated washing. Therefore, this process can be widely applied as a universal approach to overcome the challenges associated with growing inorganic nanowires on polymeric support surfaces.

Elucidating the Trade-off between Membrane Wetting Resistance and Water Vapor Flux in Membrane Distillation

Membrane distillation (MD) has been receiving considerable attention as a promising technology for desalinating industrial wastewaters. While hydrophobic membranes are essential for the process, increasing membrane surface hydrophobicity generally leads to the reduction of water vapor flux. In this study, we investigate the mechanisms responsible for this trade-off relation in MD. We prepared hydrophobic membranes with different degrees of wetting resistance through coating quartz fiber membranes with a series of alkylsilane molecules while preserving the fiber structures. A trade-off between wetting resistance and water vapor flux was observed in direct-contact MD experiments, with the least-wetting-resistant membrane exhibiting twice as high vapor flux as the most wetting-resistant membrane. Electrochemical impedance analysis, combined with fluorescence microscopy, elucidated that a lower wetting resistance (still water-repelling) allows deeper penetration of the liquid-air interfaces into the membrane, resulting in an increased interfacial area and therefore a larger evaporative vapor flux. Finally, we performed osmotic distillation experiments employing anodized alumina membranes that possess straight nanopores with different degrees of wetting resistance, observed no trade-off, and substantiated this proposed mechanism. Our study provides a guideline to tailor the membrane surface wettability to ensure stable MD operations while maximizing the water recovery rate.

Hierarchical Ti3C2Tx MXene/Ni Chain/ZnO Array Hybrid Nanostructures on Cotton Fabric for Durable Self-Cleaning and Enhanced Microwave Absorption

The increasing demand for wearable electronics and the intensification of electromagnetic pollution have boosted the exploration of high-performance flexible microwave absorption (MA) materials. Herein, the hierarchical Ti₃C₂T_x MXene/Ni chain/ZnO array hybrid nanostructures are rationally constructed on cotton fabric for acquiring enhanced MA performance and durable self-cleaning ability. Based on the high dielectric loss capacity of MXenes and ZnO arrays, by controlling dip-coating numbers of Ni chains, the magnetic loss can be manipulated to modulate the impedance matching, reflection loss (RL), and effective absorption bandwidth (EAB, the bandwidth of RL < -10 dB). The minimum RL value of the designed fabric can reach -35.1 dB at 8.3 GHz with a thickness of 2.8 mm, and its EAB can cover the whole X-band with only a 2.2 mm thickness. In addition, the designed fabric also exhibits superior liquid repellency and durable self-cleaning ability due to the combination of the hybrid nanostructures and a superhydrophobic coating. This work provides an insight for rational design of textile-based MA materials, showing potential applications in flexible and wearable functional electronics.

Mechanism of a Self-Assembling Smart and Electrically Responsive PVDF-Graphene Membrane for Controlled Gas Separation

The development of science and technology is accompanied by a complex composition of multiple pollutants. Conventional passive separation processes are not sufficient for current industrial applications. The advent of active or responsive separation methods has become highly essential for future applications. In this work, we demonstrate the preparation of a smart electrically responsive membrane, a poly(vinylidene difluoride) (PVDF)-graphene composite membrane. The high graphene content induces the self-assembly of PVDF with a high β-phase content, which displays a unique self-piezoelectric property. Additionally, the membrane exhibits excellent electrical conductivity and unique capacitive properties, and the resultant nanochannels in the membrane can be reversibly adjusted by external voltage applications, resulting in the tailored gas selectivity of a single membrane. After the application of voltage to the membrane, the permeability and selectivity toward carbon dioxide increase simultaneously. Moreover, atomic-level positron annihilation spectroscopic studies reveal the piezoelectric effect on the free volume of the membrane, which helps us to formulate a gas permeation mechanism for the electrically responsive membrane. Overall, the novel active membrane separation process proposed in this work opens new avenues for the development of a new generation of responsive membranes.

Omniphobic Nanofibrous Membrane with Pine-Needle-Like Hierarchical Nanostructures: Toward Enhanced Performance for Membrane Distillation

Wetting and fouling phenomena are the main concerns for membrane distillation (MD) in treating high-salinity industrial wastewater. This work developed an omniphobic membrane by growing titanium dioxide (TiO₂) nanorods on polyvinylidene fluoride-co-hexafluoropropylene (PVDF-HFP) nanofibers using a hydrothermal technique. The TiO₂ nanorods form a uniform pine-needle-like hierarchical nanostructure on PVDF-HFP fibers. A further fluorination treatment provides the membrane with a low-surface-energy omniphobic surface, displaying contact angles of 168° and 153° for water and mineral oil, respectively. Direct contact MD experiments demonstrated that the resulting membrane shows a high and stable salt rejection of >99.9%, while the pristine PVDF-HFP nanofibrous membrane suffers a rejection decline caused by intense pore wetting and oil fouling in the desalination process in the presence of surfactant and mineral oil. The superior antiwetting and antifouling behaviors were ascribed to a nonwetting Cassie-Baxter state established by the accumulation of a great deal of air in the hydrophobized hierarchical re-entrant structures. The development of omniphobic membranes with pine-needle-like hierarchical nanostructures provides an approach to mitigate membrane wetting and fouling in the MD process for the water reclamation from industrial wastewater.