Thioether Bond Modification Enables Boosted Photovoltaic Performance of Nonfullerene Polymer Solar Cells

Recent Progress in the Design of Fused-Ring Non-Fullerene Acceptors-Relations between Molecular Structure and Optical, Electronic, and Photovoltaic Properties

Organic solar cells are on the dawn of the next era. The change of focus toward non-fullerene acceptors has introduced an enormous amount of organic n-type materials and has drastically increased the power conversion efficiencies of organic photovoltaics, now exceeding 18%, a value that was believed to be unreachable some years ago. In this Review, we summarize the recent progress in the design of ladder-type fused-ring non-fullerene acceptors in the years 2018-2020. We thereby concentrate on single layer heterojunction solar cells and omit tandem architectures as well as ternary solar cells. By analyzing more than 700 structures, we highlight the basic design principles and their influence on the optical and electrical structure of the acceptor molecules and review their photovoltaic performance obtained so far. This Review should give an extensive overview of the plenitude of acceptor motifs but will also help to understand which structures and strategies are beneficial for designing materials for highly efficient non-fullerene organic solar cells.

High-Performance Ternary Polymer Solar Cells Enabled by a New Narrow Bandgap Nonfullerene Small Molecule Acceptor with a Higher LUMO Level

Obtaining a large open-circuit voltage (V_OC ) and high short-circuit current density (J_SC ) simultaneously is important in improving power conversion efficiency (PCE) of organic photovoltaics. The ternary strategy with using a higher lowest unoccupied molecular orbital (LUMO) level nonfullerene acceptor (NFA) guest can achieve increased V_OC , yet J_SC is decreased or maintained, so it's still a challenge to offer increased V_OC and J_SC values concurrently via the newly presented V_OC -increased ternary strategy. To overcome this issue, a new narrow bandgap NFA TT-S-4F is reported by introducing 3,6-dimethoxylthieno[3,2-b]thiophene (TT) as π-spacers to connect electron-rich core with terminal groups, so as to upshift the LUMO level and extend π-system. When adding 10% TT-S-4F into binary system based on PTB7-Th:IEICO-4F, the higher-LUMO-level of TT-S-4F, the increased charge mobilities, the reduced trap-assisted combination loss, and a finer nanofiber structure and increased phase separation size are obtained, which simultaneously promotes J_SC , V_OC , and fill factor (FF), thus obtaining an optimal PCE (12.5% vs 11.5%). This work illustrates that an extending conjugated backbone with large π-spacers and inclusion of alkylthiophenyl side-chains is a concept to synthesize NFA guests for use on the V_OC -increased ternary strategy that enables to realize simultaneously increased J_SC , V_OC , and FF.

Subtle Morphology Control with Binary Additives for High-Efficiency Non-Fullerene Acceptor Organic Solar Cells

Adding an additive is one of the effective strategies to fine-tune active layer morphology and improve performance of organic solar cells. In this work, a binary additive 1,8-diiodooctane (DIO) and 2,6-dimethoxynaphthalene (DMON) to optimize the morphology of PBDB-T:TTC8-O1-4F-based devices is reported. With the binary additive, a power conversion efficiency (PCE) of 13.22% was achieved, which is higher than those of devices using DIO (12.05%) or DMON (11.19%) individually. Comparison studies demonstrate that DIO can induce the acceptor TTC8-O1-4F to form ordered packing, while DMON can inhibit excessive aggregation of the donor and acceptor. With the synergistic effect of these two additives, the PBDB-T:TTC8-O1-4F blend film with DIO and DMON exhibits a suitable phase separation and crystallite size, leading to a high short-circuit current density (J_sc) of 23.04 mA·cm^-2 and a fill factor of 0.703 and thus improved PCE.