Surface Engineering of Metal-Organic Framework Prepared on Film Bulk Acoustic Resonator for Vapor Detection

Multi-DoF AlN-on-SOI BAW MEMS resonators with coated ZIF-8 for gas sensing application

This paper explored the practical utility of gas sensing applications based on the multi-degree-of-freedom (Multi-DoF) bulk acoustic wave (BAW) resonant sensors, including 1, 2, and 3-DoF devices, where piezoelectric actuation and sensing methods were adopted. Zeolitic imidazolate framework-8 (ZIF-8) was chosen for the adsorption and desorption of the ethanol vapor, thereby facilitating the gas sensing mechanism and introducing the external mass changes to the multi-DoF resonating system. Similar to conventional quartz crystal microbalance (QCM) gas sensors, the frequency shift of all the devices (1, 2, and 3-DoF devices) was tracked to characterize the sensitivity. Besides, for the 2 and 3-DoF devices, the amplitude ratio (AR) change was also recorded and observed with an enhancement in performance. Compared with the state-of-the-art gas sensor based on 2-DoFcapacitively coupled resonators, the presented devices achieved better Q factor in air, stability, and resolution in terms of both frequency shifts and AR changes. The dominant mass change (dominant stiffness change in the state-of-the-art) of the proposed resonant devices matched well with the theoretical mass sensing principle, which is both predictable and crucial for the accurate modeling of the practical mass sensor. Furthermore, a lower ethanol vapor concentration from 0.1% to 2% was successfully detected by the proposed 2-DoF device, demonstrating even better sensing performance than that of the state-of-the-art.

Utilizing Colorimetric Gas Sensors as a Selective Detector for Gas Chromatography

Colorimetric gas sensors show promise as selective detectors for gas chromatography (GC), but their application has been limited by the irreversibility of their responses. This study presents the successful hyphenation of colorimetric gas sensors with GC, overcoming this limitation through a novel approach that refreshes the sensor's reaction area with controlled movement, enabling the generation of reversible GC peaks. The sensors, based on acid-base indicators, such as chlorophenol red and bromocresol green, were integrated with a capillary GC column and evaluated for amine detection. Performance testing revealed satisfactory sensitivity, linearity, and reproducibility, with the colorimetric sensors demonstrating superior selectivity for amines compared to flame ionization detectors (FID). Moreover, a dual-sensor array, combined with a pattern recognition algorithm, enabled effective discrimination between various amine compounds. This work establishes a promising, cost-effective alternative for portable GC systems, enhancing selectivity and improving the capability of field vapor analysis.

Unveiling the scope and perspectives of MOF-derived materials for cutting-edge applications

Although synthesis and design of MOFs are crucial factors to the successful implementation of targeted applications, there is still lack of knowledge among researchers about the synthesis of MOFs and their derived composites for practical applications. For example, many researchers manipulate study results, and it has become quite difficult to quit this habit specifically among the young researchers Undoubtedly, MOFs have become an excellent class of compounds but there are many challenges associated with their improvement to attain diverse applications. It has been noted that MOF-derived materials have gained considerable interest owing to their unique chemical properties. These compounds have exhibited excellent potential in various sectors such as energy, catalysis, sensing and environmental applications. It is worth mentioning that most of the researchers rely on commercially available MOFs for use as precursor supports, but it is an unethical and wrong practice because it prevents the exploration of the hidden diversity of similar materials. The reported studies have significant gaps and flaws, they do not have enough details about the exact parameters used for the synthesis of MOFs and their derived materials. For example, many young researchers claim that MOF-based materials cannot be synthesized as per the reported instructions for large-scale implementation. In this regard, current article provides a comprehensive review of the most recent advancements in the design of MOF-derived materials. The methodologies and applications have been evaluated together with their advantages and drawbacks. Additionally, this review suggests important precautions and solutions to overcome the drawbacks associated with their preparation. Applications of MOF-derived materials in the fields of energy, catalysis, sensing and environment have been discussed. No doubt, these materials have become excellent class but there are still many challenges ahead to specify it for the targeted applications.

Investigation of sorptive interactions between volatile organic compounds and supramolecules at dynamic oscillation using bulk acoustic wave resonator virtual sensor arrays

Supramolecules are considered as promising materials for volatile organic compounds (VOCs) sensing applications. The proper understanding of the sorption process taking place in host-guest interactions is critical in improving the pattern recognition of supramolecules-based sensing arrays. Here, we report a novel approach to investigate the dynamic host-guest recognition process by employing a bulk acoustic wave (BAW) resonator capable of producing multiple oscillation amplitudes and simultaneously recording multiple responses to VOCs. Self-assembled monolayers (SAMs) of β-cyclodextrin (β-CD) were modified on four BAW sensors to demonstrate the gas-surface interactions regarding oscillation amplitude and SAM length. Based on the method, a virtual sensor array (VSA) type electronic nose (e-nose) can be realized by pattern recognition of multiple responses at different oscillation amplitudes of a single sensor. VOCs analysis was realized respectively by using principal component analysis (PCA) for individual VOC identification and linear discriminant analysis (LDA) for VOCs mixtures classification.

Extrusion Printing of Surface-Functionalized Metal-Organic Framework Inks for a High-Performance Wearable Volatile Organic Compound Sensor

Wearable sensors hold immense potential for real-time and non-destructive sensing of volatile organic compounds (VOCs), requiring both efficient sensing performance and robust mechanical properties. However, conventional colorimetric sensor arrays, acting as artificial olfactory systems for highly selective VOC profiling, often fail to meet these requirements simultaneously. Here, a high-performance wearable sensor array for VOC visual detection is proposed by extrusion printing of hybrid inks containing surface-functionalized sensing materials. Surface-modified hydrophobic polydimethylsiloxane (PDMS) improves the humidity resistance and VOC sensitivity of PDMS-coated dye/metal-organic frameworks (MOFs) composites. It also enhances their dispersion within liquid PDMS matrix, thereby promoting the hybrid liquid as high-quality extrusion-printing inks. The inks enable direct and precise printing on diverse substrates, forming a uniform and high particle-loading (70 wt%) film. The printed film on a flexible PDMS substrate demonstrates satisfactory flexibility and stretchability while retaining excellent sensing performance from dye/MOFs@PDMS particles. Further, the printed sensor array exhibits enhanced sensitivity to sub-ppm VOC levels, remarkable resistance to high relative humidity (RH) of 90%, and the differentiation ability for eight distinct VOCs. Finally, the wearable sensor proves practical by in situ monitoring of wheat scab-related VOC biomarkers. This study presents a versatile strategy for designing effective wearable gas sensors with widespread applications.

Advances and Applications of Metal-Organic Frameworks (MOFs) in Emerging Technologies: A Comprehensive Review

Metal-organic frameworks (MOFs) that are the wonder material of the 21st century consist of metal ions/clusters coordinated to organic ligands to form one- or more-dimensional porous structures with unprecedented chemical and structural tunability, exceptional thermal stability, ultrahigh porosity, and a large surface area, making them an ideal candidate for numerous potential applications. In this work, the recent progress in the design and synthetic approaches of MOFs and explore their potential applications in the fields of gas storage and separation, catalysis, magnetism, drug delivery, chemical/biosensing, supercapacitors, rechargeable batteries and self-powered wearable sensors based on piezoelectric and triboelectric nanogenerators are summarized. Lastly, this work identifies present challenges and outlines future opportunities in this field, which can provide valuable references.

Microgravimetric Modeling-A New Method for Extracting Adsorption Parameters of Functionalized MIL-101(Cr)

As a volatile air pollutant, formaldehyde can enter people's living environment through interior decoration, furniture and paint, causing serious harm to human health. Therefore, it is necessary to develop a sensor for the real-time detection of formaldehyde in low concentrations. According to the chemical interaction between amino groups and formaldehyde, a MIL-101(Cr) aminated-material-based formaldehyde cantilever sensor was prepared, of which ethylenediamine- functionalized MIL-101(Cr) named ED-MIL-101(Cr)) showed the best gas sensing performance. Using quasi-in situ infrared spectroscopy, ED-MIL-101(Cr) was found bound to formaldehyde through a Schiff base. The adsorption enthalpy of formaldehyde-bound ED-MIL-101(Cr) was -52.6 kJ/mol, which corresponds to weak chemical adsorption, so the material showed good selectivity. In addition, ED-MIL-101(Cr) has the most active sites, so its response value to formaldehyde is larger and it takes longer to reach saturation adsorption than bare MIL-101(Cr). Through the research on the gas sensing performance of functionalized MIL-101(Cr) material, we found that it has a strong application potential in the field of formaldehyde monitoring, and the material performance can be quantitatively and accurately evaluated through combining calculation and experimentation for understanding the gas sensing mechanism.

Nanoscale carbon dot-embedded metal-organic framework for turn-on fluorescence detection of water in organic solvents

An easy-to-use, highly selective, and real-time organic solvent quality assessment is desirable to detect water contamination in organic solvents. Herein, a one-step procedure using ultrasound irradiation was used for encapsulating nanoscale carbon dots (CDs) into metal-organic framework-199 (HKUST-1) to form CDs@HKUST-1 composite. The CDs@HKUST-1 exhibited very weak fluorescence due to photo-induced electron transfer (PET) from the CDs to the Cu²⁺ centers, acting as a fluorescent sensor in its off-state. The designed material can detect and discriminate water from other organic solvents, driven by turn-on fluorescence. This highly sensitive sensing platform could be applied for the detection of water in ethanol, acetonitrile, and acetone with wide linear detection ranges of 0-70% v/v, 2-12% v/v, and 10-50% v/v and limits of detection of 0.70% v/v, 0.59% v/v, and 1.08% v/v, respectively. The detection mechanism is attributed to the interruption of the PET process due to the release of fluorescent CDs after treatment with water. A smartphone-based quantitative test was successfully developed to monitor the water content in organic solvents utilizing CDs@HKUST-1 and a phone color processing application, thus making it possible to develop an on-site, real time and easy-to-use sensor for water detection.

A review of piezoelectric MEMS sensors and actuators for gas detection application

Piezoelectric microelectromechanical system (piezo-MEMS)-based mass sensors including the piezoelectric microcantilevers, surface acoustic waves (SAW), quartz crystal microbalance (QCM), piezoelectric micromachined ultrasonic transducer (PMUT), and film bulk acoustic wave resonators (FBAR) are highlighted as suitable candidates for highly sensitive gas detection application. This paper presents the piezo-MEMS gas sensors' characteristics such as their miniaturized structure, the capability of integration with readout circuit, and fabrication feasibility using multiuser technologies. The development of the piezoelectric MEMS gas sensors is investigated for the application of low-level concentration gas molecules detection. In this work, the various types of gas sensors based on piezoelectricity are investigated extensively including their operating principle, besides their material parameters as well as the critical design parameters, the device structures, and their sensing materials including the polymers, carbon, metal-organic framework, and graphene.

Two-Dimensional Nitrogen-Doped Carbon Nanosheets Derived from g-C3N4 /ZIF-8 for Solid-Phase Microextraction in Exhalation of Esophageal Cancer Patients

Here, two-dimensional (2D) nitrogen-doped carbon nanosheets (CNSs) were prepared through carbonizing MOFs (ZIF-8) in-situ grown using graphitic carbon nitride (g-C₃N₄) as a template. The developed ZIF-8 CNS was then used as solid-phase microextraction (SPME) fiber coating for beneficiation of five biomarkers in exhalation of patients with esophageal cancer and in gas chromatography-mass spectrometry (GC-MS) for determination. The ZIF-8 CNS fiber exhibits satisfactory enrichment factors (3490-5631), wide linearity (5-1000 μg L^-1), and low detection limits (0.26-0.96 μg L^-1). The relative standard deviations (RSDs) for six replicate extractions of the same ZIF-8 CNS fiber were between 2.0-3.9% (intra-day) and 2.8-5.2% (inter-day). The reproducibility of three fibers prepared by the same approach was in the range 6.8-12.3% (RSD). The developed ZIF-8 CNS fiber can persist in 120 SPME cycles with no prominent loss of extraction efficiency and precision. The high enrichment factors of the 2D ZIF-8 CNS coatings are attributed to the high specific surface area, ultrathin thickness, and nano-pore or interlayer channels; moreover, nitrogen doping also endows the π system with a strong electron absorption ability, which will enhance the π-π interaction between the ZIF-8 CNS and the aromatic ring. Ultimately, the self-made ZIF-8 CNS-coated SPME fiber was applied to the analysis of exhaled breath samples. The recoveries of spiked analytes are between 84 and 105%.

A prototype portable instrument employing micro-preconcentrator and FBAR sensor for the detection of chemical warfare agents

The presence of chemical warfare agents (CWAs) in the environment is a serious threat to human safety, but there are many problems with the currently available detection methods for CWAs. For example, gas chromatography–mass spectrometry cannot be used for in-field detection owing to the rather large size of the equipment required, while commercial sensors have the disadvantages of low sensitivity and poor selectivity. Here, we develop a portable gas sensing instrument for CWA detection that consists of a MEMS-fabricated micro-preconcentrator (μPC) and a film bulk acoustic resonator (FBAR) gas sensor. The μPC is coated with a nanoporous metal–organic framework material to enrich the target, while the FBAR provides rapid detection without the need for extra carrier gas. Dimethyl methylphosphonate (DMMP), a simulant of the chemical warfare agent sarin, is used to test the performance of the instrument. Experimental results show that the μPC provides effective sample pretreatment, while the FBAR gas sensor has good sensitivity to DMMP vapor. The combination of μPC and FBAR in one instrument gives full play to their respective advantages, reducing the limit of detection of the analyte. Moreover, both the μPC and the FBAR are fabricated using a CMOS-compatible approach, and the prototype instrument is compact in size with high portability and thus has potential for application to in-field detection of CWAs.

Metal-Organic Framework Based Gas Sensors

The ever-increasing concerns over indoor/outdoor air quality, industrial gas leakage, food freshness, and medical diagnosis require miniaturized gas sensors with excellent sensitivity, selectivity, stability, low power consumption, cost-effectiveness, and long lifetime. Metal-organic frameworks (MOFs), featuring structural diversity, large specific surface area, controllable pore size/geometry, and host-guest interactions, hold great promises for fabricating various MOF-based devices for diverse applications including gas sensing. Tremendous progress has been made in the past decade on the fabrication of MOF-based sensors with elevated sensitivity and selectivity toward various analytes due to their preconcentrating and molecule-sieving effects. Although several reviews have recently summarized different aspects of this field, a comprehensive review focusing on MOF-based gas sensors is absent. In this review, the latest advance of MOF-based gas sensors relying on different transduction mechanisms, for example, chemiresistive, capacitive/impedimetric, field-effect transistor or Kelvin probe-based, mass-sensitive, and optical ones are comprehensively summarized. The latest progress for making large-area MOF films essential to the mass-production of relevant gas sensors is also included. The structural and compositional features of MOFs are intentionally correlated with the sensing performance. Challenges and opportunities for the further development and practical applications of MOF-based gas sensors are also given.

The synthesis of metal-organic frameworks with template strategies

The synthesis of metal-organic frameworks (MOFs) with a template strategy is still fascinating and has received considerable attention from structural chemists. In this review, developments in tuning MOF hosts or pore structures with a template strategy in the past decades are summarized. By adding templates into MOF precursors, novel template@MOF materials can always be obtained, which cannot be accessed by traditional synthesis procedures. Template@MOF materials can be structurally characterized to help understand the interactions between host frameworks and guest templates. On the other hand, changing the species or amount of template may lead to a pore structure change that can be used as a molecular container to load functional guest molecules with matching sizes for specific applications. It is hoped that this review will provide future researchers with new insight into the design and synthesis of MOF materials by applying suitable templates.